PWM-120-12 Constant Voltage PWM Output KNX LED Driver
“
Product Specifications
| MODEL | DC VOLTAGE | RATED CURRENT | RATED POWER | DIMMING RANGE | OUTPUT |
|---|---|---|---|---|---|
| PWM-120-12 | 12V | 10A | 120W | 0 ~ 100% | PWM Output KNX LED Driver |
| PWM-120-24 | 24V | 5A | 120W | 0 ~ 100% | PWM Output KNX LED Driver |
Product Usage Instructions
Installation
1. Ensure the input power is within the specified voltage range
(90-305VAC, 127-431VDC).
2. Connect the driver to the LED lighting system following the
correct polarity.
Dimming Settings
1. Use the ETS software to adjust the PWM frequency within the
range of 200-4000Hz.
2. Dimming range can be set from 0% to 100% as per your lighting
requirements.
Power Management
1. The driver has a power factor of PF>0.97/115VAC,
PF>0.96/230VAC, PF>0.94/277VAC at full load.
2. Total harmonic distortion is maintained below 20% under
specified load conditions.
Safety Precautions
1. Do not exceed the maximum number of PSUs allowed on a circuit
breaker to prevent overload.
2. Follow proper grounding and wiring practices during
installation to avoid electric shock hazards.
Frequently Asked Questions (FAQ)
Q: Can the dimming range be adjusted on the PWM-120-KN LED
driver?
A: Yes, the dimming range can be adjusted from 0% to 100% using
compatible software.
Q: What is the typical efficiency of the PWM-120-KN
driver?
A: The typical efficiency is 88.5% for the 12V model and 90% for
the 24V model.
Q: How many units of PWM-120-KN drivers can be connected to a
circuit breaker?
A: You can connect up to 4 units with a circuit breaker of type
B or up to 6 units with a circuit breaker of type C at 230VAC.
“`
PWM-120-KN 120W Constant Voltage PWM Output KNX LED Driver
series
User’s Manual
05
.%
File Name:PWM-120-KN-SPEC 2024-03-12
120W PWM Output KNX LED Driver
PWM-120-KN series
SPECIFICATION
MODEL
PWM-120-12
PWM-120-24
DC VOLTAGE
12V
24V
RATED CURRENT
10A
5A
RATED POWER
120W
120W
DIMMING RANGE
0 ~ 100%
OUTPUT
PWM FREQUENCY (Typ.) 200~4000Hz user changable via ETS
SETUP, RISE TIME Note.2 500ms, 80ms/ 230VAC or 115VAC
HOLD UP TIME (Typ.) 16ms/230VAC or 115VAC
VOLTAGE RANGE Note.3
90 ~ 305VAC 127 ~ 431VDC (Please refer to “STATIC CHARACTERISTIC” section)
FREQUENCY RANGE 47 ~ 63Hz
POWER FACTOR (Typ.)
PF>0.97/115VAC, PF>0.96/230VAC, PF>0.94/277VAC @ full load (Please refer to “POWER FACTOR (PF) CHARACTERISTIC” section)
TOTAL HARMONIC DISTORTION
THD< 20%(@load60%/115VAC, 230VAC; @load75%/277VAC) (Please refer to “TOTAL HARMONIC DISTORTION” section)
INPUT
EFFICIENCY (Typ.)
88.5%
90%
AC CURRENT (Typ.)
1.3A / 115VAC 0.65A / 230VAC 0.55A / 277VAC
INRUSH CURRENT (Typ.) COLD START 60A(twidth=520s measured at 50% Ipeak) at 230VAC; Per NEMA 410
MAX. NO. of PSUs on 16A CIRCUIT BREAKER
4 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT
<0.25mA / 277VAC
STANDY POWER CONSUMPTION <0.5W
OVERLOAD
108 ~ 130% rated output power Hiccup mode, recovers automatically after fault condition is removed
SHORT CIRCUIT
Shut down o/p voltage, re-power on to recover
PROTECTION OVER VOLTAGE
15 ~ 17V Shut down o/p voltage, re-power on to recover
28 ~ 34V
OVER TEMPERATURE Shut down o/p voltage, re-power on to recover
WORKING TEMP.
Tcase=-40 ~ +90 (Please refer to ” OUTPUT LOAD vs TEMPERATURE” section)
MAX. CASE TEMP.
Tcase=+90
WORKING HUMIDITY
20 ~ 95% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +80, 10 ~ 95% RH
TEMP. COEFFICIENT
±0.03%/ (0 ~ 45,except 0 ~ 40 for 12V)
VIBRATION
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
SAFETY STANDARDS
Note.5
ENEC BS EN/EN61347-1, BS EN/EN61347-2-13, BS EN/EN62384 independent, GB19510.14,GB19510.1, EAC TP TC 004 approved
KNX STANDARDS
Certified protocol
WITHSTAND VOLTAGE
SAFETY &
EMC
ISOLATION RESISTANCE
EMC EMISSION Note.6
EMC IMMUNITY
MTBF
I/P-O/P:3.75KVAC
I/P-O/P:100M Ohms / 500VDC / 25/ 70% RH
Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C (@load60%) ; BS EN/EN61000-3-3, GB/T 17743, GB17625.1;EAC TP TC 020
Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN61547, light industry level (surge immunity Line-Line 2KV),EAC TP TC 020 1915.2K hrs min. Telcordia SR-332 (Bellcore) ; 205.8K hrs min. MIL-HDBK-217F (25)
OTHERS DIMENSION
191*63*37.5mm (L*W*H)
NOTE
PACKING
0.80Kg; 15pcs/13.0Kg/0.87CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25 of ambient temperature. 2. De-rating may be needed under low input voltages. Please refer to “STATIC CHARACTERISTIC” sections for details. 3. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time. 4. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected
by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. (as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf) 5. This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 75or less. 6. Please refer to the warranty statement on MEAN WELL’s website at http://www.meanwell.com 7. The ambient temperature derating of 3.5/1000m with fanless models and of 5/1000m with fan models for operating altitude higher than 2000m(6500ft). 8. For any application note and IP water proof function installation caution, please refer our user manual before using. https://www.meanwell.com/Upload/PDF/LED_EN.pdf
Product Liability DisclaimerFor detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx
File Name:PWM-120-KN-SPEC 2024-03-12
120W PWM Output KNX LED Driver
DIMMING OPERATION
AC/L(Brown) AC/N(Blue)
PWM-120-KN
PWM-120-KN series
KNX+(Red) KNX-(Black) +V(Red) -V(Black)
Dimming principle for PWM style output Dimming is achieved by varying the duty cycle of the output current.
Output DC current ON
Io=0A
OFF TON
T
TON Duty cycle(%) =
×100%
T
Output PWM frequency up to 4KHz
KNXInterface Apply KNX signal between KNX+ and KNX-. The application program(database) can be downloaded via Online Catalogs from ETS or via http://www.meanwell.com/productCatalog.aspx
File Name:PWM-120-KN-SPEC 2024-03-12
LOAD (%)
120W PWM Output KNX LED Driver
OUTPUT LOAD vs TEMPERATURE
PWM-120-KN series
100
80 230VAC Input only
60 50 40
20
12V only
-40 -25
0
15
30
40 45 50
60
AMBIENT TEMPERATURE,Ta ()
70 (HORIZONTAL)
LOAD (%)
100
80 230VAC Input only
60
40
20
-40 -25 0
20
45
65
75
85
90 (HORIZONTAL)
Tcase ()
STATIC CHARACTERISTIC
100 90 80 70 60 50 40
90 100 125 135 145 155 165 175 180 200 230 305
INPUT VOLTAGE (V) 60Hz De-rating is needed under low input voltage.
TOTAL HARMONIC DISTORTION (THD)
24V Model, Tcase at 80
25
20
15
10
5
0
50%
60%
70%
80%
90%
100%
LOAD
115VAC 230VAC 277VAC
EFFICIENCY(%)
PF
POWER FACTOR (PF) CHARACTERISTIC
Tcase at 80
1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1
0 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
LOAD
115V 230V 277V
EFFICIENCY vs LOAD
PWM-120-KN series possess superior working efficiency that up to 90% can be reached in field applications. 24V Model, Tcase at 80
100 90 80 70 60 50 40 30 20 10
0 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
LOAD
115V 230V 277V
THD LOAD (%)
File Name:PWM-120-KN-SPEC 2024-03-12
120W PWM Output KNX LED Driver
PWM-120-KN series
LIFETIME
LIFETIME(Kh)
120
100
80
60
40
20
0
20
30
40
50
60
70
80
90
Tcase( )
File Name:PWM-120-KN-SPEC 2024-03-12
120W PWM Output KNX LED Driver
PWM-120-KN series
Block Diagram
EMI FILTER
I/P
&
RECTIFIERS
PFC CIRCUIT
POWER SWITCHING
O.T.P.
O.L.P.
PWM & PFC CONTROL
RECTIFIERS &
FILTER
PFC fosc : 50~120KHz PWM fosc : 60~130KHz
O.L.P.
DIMMING CIRCUIT
DETECTION CIRCUIT
+V -V KNX+ KNX-
O.V.P.
Note: PWM fosc here is not related to ouput PWM dimming
Mechanical Specification
300±20
AC/L(Brown) AC/N(Blue)
50±3 SJTW 18AWG×2C
5
191 KNX programming button & LED
5
63 31.5
2-4.5
T case tc
95.5
5
tc : Max. Case Temperature
5
Case No. PWM-120-KN
Unit:mm
350±10
UL2464 20AWG×2C
SJOW 17AWG×2C 50±3 300±10
KNX+(Red) KNX-(Black) +V(Red) -V(Black)
KNX connector is included in the box
37.5
3
Mechanical view of by request
AC/L(Brown) AC/N(Blue)
KNX+(Red) KNX-(Black) +V(Red) -V(Black)
File Name:PWM-120-KN-SPEC 2024-03-12
120W PWM Output KNX LED Driver
Recommend Mounting Direction
Installation Manual Connection for KNX-type
PWM-120-KN series
AC/L(BROWN) AC/N(BLUE)
Vo+(RED)
+
–
Vo-(BLACK)
KNX+(RED)
LED strip or constant voltage LED bulb
KNX-(BLACK) PWM KN series can be ETS adressing/programming WITHOUT connecting to AC mains
KNX Bus
Cautions Before commencing any installation or maintenance work, please disconnect the power supply from the utility. Ensure that it cannot be re-connected inadvertently! Keep proper ventilation around the unit and do not stack any object on it. Also a 10-15 cm clearance must be kept when the adjacent device is a heat source. Mounting orientations other than standard orientation or operate under high ambient temperature may increase the internal component temperature and will require a de-rating in output current. Current rating of an approved primary /secondary cable should be greater than or equal to that of the unit. Please refer to its specification. Tc max. is identified on the product label. Please make sure that temperature of Tc point will not exceed limit. DO NOT connect “KNX- to Vo-“. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
File Name:PWM-120-KN-SPEC 2024-03-12
Documents / Resources
 |
MEAN WELL PWM-120-12 Constant Voltage PWM Output KNX LED Driver [pdf] Owner's Manual PWM-120-12, PWM-120-24, PWM-120-12 Constant Voltage PWM Output KNX LED Driver, PWM-120-12, Constant Voltage PWM Output KNX LED Driver, PWM Output KNX LED Driver, LED Driver |