MEAN-logo

MEAN WELL NPF-90D Series Single Output LED Driver

MEAN-WELL-NPF-90D-Series-Single-Output-LED-Driver-product

90W Single Output LED Driver
NPF-90D seriesMEAN-WELL-NPF-90D-Series-Single-Output-LED-Driver- (1)

MEAN-WELL-NPF-90D-Series-Single-Output-LED-Driver- (2)

Features

  • Plastic housing with class || design
  • Built-in active PFC function
  • Class 2 power unit (except NPF-90D-12/15)
  • Standby power consumption <0.5W
  • IP67 rating for indoor or outdoor installations
  • Function: 3 in 1 dimming (dim-to-off)
  • Typical lifetime >50000hours
  • 5 years warranty

Applications

  • LED panel lighting
  • LED downlight
  • LED decorative lighting
  • LED tunnel lighting
  • Moving sign

GTIN CODE
MW Search: https://www.meanwell.com/serviceGTIN.aspx

Description
NPF-90D series is a 90W AC/DC LED driver featuring the constant current mode output. NPF-90D operates from 90~305VAC and offers models with different rated voltage ranging between 12V and 54V. Thanks to the high efficiency up to 90%, with the fanless design, the entire series is able to operate for -40~+85°C case temperature under free air convection. The entire series is rated with IP67 ingress protection level and is suitable to work for a variety of applications at dry, damp or wet locations. NPF-90D is equipped with the 3 in 1 dimming function so as to provide the design flexibility for LED lighting system.

Model Encoding

MEAN-WELL-NPF-90D-Series-Single-Output-LED-Driver- (3)

SPECIFICATION

MODEL NPF-90D-12 NPF-90D-15 NPF-90D-20 NPF-90D-24 NPF-90D-30 NPF-90D-36 NPF-90D-42 NPF-90D-48 NPF-90D-54
 

 

OUTPUT

RATED CURRENT 7.5A 6A 4.5A 3.75A 3A 2.5A 2.15A 1.88A 1.67A
RATED POWER 90W 90W 90W 90W 90W 90W 90.3W 90.24W 90.18W
CONSTANT CURRENT REGION 7.2 ~ 12V 9 ~ 15V 12 ~ 20V 14.4 ~ 24V 18 ~ 30V 21.6 ~ 36V 25.2 ~ 42V 28.8 ~ 48V 32.4 ~ 54V
CURRENT RIPPLE 5.0% max. @rated current
CURRENT TOLERANCE ±5.0%
SET UP TIME Note.3 500ms/115VAC, 230VAC
 

 

 

 

 

 

INPUT

VOLTAGE RANGE Note.2 90 ~ 305VAC           127 ~ 431VDC

(Please refer to “STATIC CHARACTERISTIC” section)

FREQUENCY RANGE 47 ~ 63Hz
POWER FACTOR (Typ.) PF≧0.98/115VAC, PF≧0.96/230VAC, PF≧0.94/277VAC@full load

(Please refer to “POWER FACTOR (PF) CHARACTERISTIC” section)

TOTAL HARMONIC DISTORTION THD< 20%(@load≧60%/115VC, 230VAC; @load≧75%/277VAC)

(Please refer to “TOTAL HARMONIC DISTORTION(THD)” section)

EFFICIENCY(Typ.) 88% 89% 90% 90% 89% 90% 90% 90% 90%
AC CURRENT (Typ.) 0.95A / 115VAC 0.5A / 230VAC 0.4A / 277VAC        
INRUSH CURRENT(Typ.) COLD START 60A(twidth=550μs measured at 50% Ipeak) at 230VAC; Per NEMA 410
MAX. NO. of PSUs on 16A CIRCUIT BREAKER 3 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT <0.25mA / 277VAC
STANDBY POWER CONSUMPTION <0.5W
 

 

PROTECTION

OVER CURRENT 95 ~ 108%
Constant current limiting, recovers automatically after fault condition is removed
SHORT CIRCUIT Hiccup mode, recovers automatically after fault condition is removed
 

OVER VOLTAGE

15 ~ 17V 17.5 ~ 21V 23 ~ 27V 28 ~ 34V 34 ~ 40V 41 ~ 46V 46 ~ 54V 54 ~ 60V 59 ~ 66V
Shut down o/p voltage, re-power on to recover
OVER TEMPERATURE Shut down o/p voltage, re-power on to recover
 

 

ENVIRONMENT

WORKING TEMP. Tcase=-40 ~ +85℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)
MAX. CASE TEMP. Tcase=+85℃
WORKING HUMIDITY 20 ~ 95% RH non-condensing
STORAGE TEMP., HUMIDITY -40 ~ +80℃, 10 ~ 95% RH
TEMP. COEFFICIENT ±0.03%/℃ (0 ~ 50℃)
VIBRATION 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
 

 

SAFETY & EMC

SAFETY STANDARDS UL8750, CSA C22.2 No. 250.13-12, ENEC BS EN/EN61347-1, BS EN/EN61347-2-13, BS EN/EN62384

independent,EAC TP TC 004, GB19510.1,GB19510.14, IP67 approved ;Design refer to BS EN/EN60335-1

WITHSTAND VOLTAGE I/P-O/P:3.75KVAC
ISOLATION RESISTANCE I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
EMC EMISSION Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C (@ load≧60%) ; BS EN/EN61000-3-3; GB/T 17743, GB17625.1,EAC TP TC 020
EMC IMMUNITY Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN61547, light industry level(surge immunity Line-Line 2KV);EAC TP TC 020
 

OTHERS

MTBF 2749.1K hrs min.       Telcordia SR-332 (Bellcore) ;   231.2K hrs min.       MIL-HDBK-217F (25℃)
DIMENSION 171*63*37.5mm (L*W*H)
PACKING 0.77Kg; 18pcs/14.9Kg/0.82CUFT
NOTE
  1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature.
  2. De-rating may be needed under low input voltages. Please refer to “STATIC CHARACTERISTIC” sections for details.
  3. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time.
  4. The standby power consumption is specified for 230VAC.
  5. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. (as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf)
  6. This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 75℃ or less.
  7. Please refer to the warranty statement on MEAN WELL’s website at http://www.meanwell.com
  8. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft).
  9. For any application note and IP water proof function installation caution, please refer our user manual before using. https://www.meanwell.com/Upload/PDF/LED_EN.pdf
  10. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently connected to the mains.

※ Product Liability Disclaimer:For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx

BLOCK DIAGRAM

MEAN-WELL-NPF-90D-Series-Single-Output-LED-Driver- (4)

DRIVING METHODS OF LED MODULE

This series works in constant current mode to directly drive the LEDs.

  • In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems.
  • Should there be any compatibility issues, please contact MEAN WELL.

MEAN-WELL-NPF-90D-Series-Single-Output-LED-Driver- (5)

DIMMING OPERATION

MEAN-WELL-NPF-90D-Series-Single-Output-LED-Driver- (6)

3 in 1 dimming function

  • Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 0 ~ 10VDC, or 10V PWM signal or resistance.
  • Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers.
  • Dimming source current from power supply: 100μA (typ.)

Applying additive 0 ~ 10VDC

MEAN-WELL-NPF-90D-Series-Single-Output-LED-Driver- (7) MEAN-WELL-NPF-90D-Series-Single-Output-LED-Driver- (8)

Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz):

MEAN-WELL-NPF-90D-Series-Single-Output-LED-Driver- (9) MEAN-WELL-NPF-90D-Series-Single-Output-LED-Driver- (10)

Applying additive resistance

MEAN-WELL-NPF-90D-Series-Single-Output-LED-Driver- (11) MEAN-WELL-NPF-90D-Series-Single-Output-LED-Driver- (12)

Note 

  1. Min. dimming level is about 6% and the output current is not defined when 0%< Iout<6%.
  2. The output current could drop down to 0% when dimming input is about 0kΩ or 0Vdc, or 10V PWM signal with 0% duty cycle.

OUTPUT LOAD vs TEMPERATURE

MEAN-WELL-NPF-90D-Series-Single-Output-LED-Driver- (13)

STATIC CHARACTERISTIC

MEAN-WELL-NPF-90D-Series-Single-Output-LED-Driver- (14)

De-rating is needed under low input voltage.

POWER FACTOR (PF) CHARACTERISTIC

MEAN-WELL-NPF-90D-Series-Single-Output-LED-Driver- (15)

TOTAL HARMONIC DISTORTION (THD)

48V Model, Tcase at 75℃

MEAN-WELL-NPF-90D-Series-Single-Output-LED-Driver- (16) EFFICIENCY vs LOAD
NPF-90D series possess superior working efficiency that up to 90.5% can be reached in field applications.
48V Model, Tcase at 75℃MEAN-WELL-NPF-90D-Series-Single-Output-LED-Driver- (17)

LIFE TIME

MEAN-WELL-NPF-90D-Series-Single-Output-LED-Driver- (18)

MECHANICAL SPECIFICATION

MEAN-WELL-NPF-90D-Series-Single-Output-LED-Driver- (19)

Recommend Mounting Direction

MEAN-WELL-NPF-90D-Series-Single-Output-LED-Driver- (20)

 

INSTALLATION MANUAL

Please refer to : http://www.meanwell.com/manual.html

File Name: NPF-90D-SPEC 2024-03-01

Documents / Resources

MEAN WELL NPF-90D Series Single Output LED Driver [pdf] Owner's Manual
NPF-90D-12, NPF-90D-15, NPF-90D-20, NPF-90D-24, NPF-90D-30, NPF-90D-36, NPF-90D-42, NPF-90D-48, NPF-90D-54, NPF-90D Series Single Output LED Driver, NPF-90D Series, Single Output LED Driver, Output LED Driver, LED Driver

References

Leave a comment

Your email address will not be published. Required fields are marked *