LPF-16D Series 16W Constant Current Mode LED Driver
16W Constant Current Mode LED Driver
LPF-16D series
User’s Manual
IP30
File Name:LPF-16D-SPEC 2024-10-16
16W Constant Current Mode LED Driver
LPF-16D series
SPECIFICATION
MODEL
LPF-16D-12 LPF-16D-15 LPF-16D-20 LPF-16D-24 LPF-16D-30 LPF-16D-36 LPF-16D-42 LPF-16D-48 LPF-16D-54
DC VOLTAGE RATED CURRENT
12V
15V
20V
1.34A
1.07A
0.8A
24V
30V
36V
42V
48V
54V
0.67A
0.54A
0.45A
0.39A
0.34A
0.3A
OUTPUT
RATED POWER
Note.5 16.08W
16.05W
CONSTANT CURRENT REGION Note.2 6.6 ~12V 8.25 ~ 15V
CURRENT RIPPLE
5.0% max. @rated current
CURRENT TOLERANCE
±5.0%
16W 11 ~ 20V
16.08W
16.2W
16.2W
16.38W
16.32W
16.2W
13.2 ~ 24V 16.5 ~ 30V 19.8 ~ 36V 23.1 ~ 42V 26.4 ~ 48V 29.7 ~ 54V
SETUP, RISE TIME Note.6 1500ms, 80ms / 115VAC 500ms, 80ms / 230VAC
HOLD UP TIME (Typ.)
16ms/230VAC 16ms/115VAC
VOLTAGE RANGE
90 ~ 305VAC 127 ~ 431VDC Note.5 (Please refer to “STATIC CHARACTERISTIC” section)
FREQUENCY RANGE
47 ~ 63Hz
POWER FACTOR
PF0.97/115VAC, PF0.95/230VAC, PF0.92/277VAC@full load (Please refer to “POWER FACTOR (PF) CHARACTERISTIC” section)
TOTAL HARMONIC DISTORTION
THD< 20%(@load60%/115VC,230VAC; @load75%/277VAC) (Please refer to “TOTAL HARMONIC DISTORTION(THD)” section)
INPUT
EFFICIENCY (Typ.)
83%
83%
84.5%
84.5%
84.5%
85%
85%
85%
84.5%
AC CURRENT
0.4A / 115VAC 0.25A / 230VAC 0.2A/277VAC
INRUSH CURRENT(Typ.)
COLD START 45A(twidth=200s measured at 50% Ipeak) at 230VAC; Per NEMA 410
MAX. No. of PSUs on 16A CIRCUIT BREAKER
14 units (circuit breaker of type B) / 24 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT
<0.75mA / 240VAC
OVER CURRENT
SHORT CIRCUIT PROTECTION
OVER VOLTAGE
OVER TEMPERATURE
95 ~ 108% Constant current limiting, recovers automatically after fault condition is removed Hiccup mode, recovers automatically after fault condition is removed. 15 ~ 18V 17.5 ~ 21V 23 ~ 27V 28 ~ 35V 34 ~ 40V 41 ~ 49V Shut down and latch off o/p voltage, re-power on to recover Shut down o/p voltage, recovers automatically after temperature goes down
46 ~ 54V
54 ~ 63V
59 ~ 66V
WORKING TEMP. MAX. CASE TEMP.
WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
Tcase=-35 ~ +70 (Please refer to ” OUTPUT LOAD vs TEMPERATURE” section) Tcase=+70 20 ~ 95% RH non-condensing -40 ~ +80, 10 ~ 95% RH ±0.03%/ (0 ~ 50)
VIBRATION
10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes
SAFETY STANDARDS Note.8
UL8750, CSA C22.2 No. 250.0-08, ENEC BS EN/EN61347-1, BS EN/EN61347-2-13 independent,BS EN/EN62384, EAC TP TC 004,GB19510.1,GB19510.14 approved, IP67(optional); Design refer to UL60950-1
SAFETY & WITHSTAND VOLTAGE
EMC
ISOLATION RESISTANCE
EMC EMISSION Note.8
I/P-O/P:3.75KVAC
I/P-O/P:100M Ohms / 500VDC / 25/ 70% RH Compliance to BS EN/EN55015,BS EN/EN61000-3-2 Class C (@load55%) ; BS EN/EN61000-3-3,GB/T 17743 , GB17625.1, EAC TP TC 020
OTHERS NOTE
EMC IMMUNITY
Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN61547, light industry level (surge immunity Line-Line 2KV),EAC TP TC 020
MTBF
3572.8K hrs min. Telcordia SR-332 (Bellcore) ; 391.6Khrs min. MIL-HDBK-217F (25)
DIMENSION
148*40*32mm (L*W*H)
PACKING
0.21Kg;40pcs/9.4Kg/ 1.02CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25 of ambient temperature.
2. Please refer to “DRIVING METHODS OF LED MODULE”.
3. Ripple & noise are measured at 20MHz of bandwidth by using a 12″ twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
4. Tolerance : includes set up tolerance, line regulation and load regulation.
5. De-rating may be needed under low input voltages. Please refer to “STATIC CHARACTERISTIC” sections for details.
6. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time. 7. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
(as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf)
8. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED driver can only be used behind a switch
without permanently connected to the mains. 9. This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 70 or less.
10. Please refer to the warranty statement on MEAN WELL’s website at http://www.meanwell.com 11. The ambient temperature derating of 3.5/1000m with fanless models and of 5/1000m with fan models for operating altitude higher than 2000m(6500ft).
12. For any application note and IP water proof function installation caution, please refer our user manual before using.
https://www.meanwell.com/Upload/PDF/LED_EN.pdf
Product Liability DisclaimerFor detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx
File Name:LPF-16D-SPEC 2024-10-16
16W Constant Current Mode LED Driver
BLOCK DIAGRAM
LPF-16D series
fosc : 100KHz
EMI FILTER
I/P
&
RECTIFIERS
PFC CIRCUIT
POWER SWITCHING
O.L.P.
PWM & PFC CONTROL
RECTIFIERS &
FILTER
O.L.P.
DETECTION CIRCUIT
O.V.P.
+V -V DIM+ DIM-
DRIVING METHODS OF LED MODULE
This series works in constant current mode to directly drive the LEDs.
Vo(%)
100
60 (min.)
Constant Current area
In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN WELL.
Hiccup Protection
50
100
Io(%)
Typical output current normalized by rated current (%)
File Name:LPF-16D-SPEC 2024-10-16
16W Constant Current Mode LED Driver
DIMMING OPERATION
3 in 1 dimming function
LPF-16D series
AC/N(Blue) AC/L(Brown)
LPF-16D
+V(Red) -V(Black) DIM+(Purple) DIM-(Pink)
Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 1 ~ 10VDC, or 10V PWM signal or resistance.
Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: 100A (typ.)
Applying additive 1 ~ 10VDC
100%
+V +
90%
+
80%
Output current (%)
-V
70%
–
60%
DIM+ +
50%
Additive Voltage
40%
–
30%
DIM-
20%
“DO NOT connect “DIM- to -V”
10% 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V
Dimming input: Additive voltage
Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz):
+V +
+
-V
–
–
DIM+
Additive PWM signal
DIM-
“DO NOT connect “DIM- to -V”
Output current (%)
100% 90% 80% 70% 60% 50% 40% 30% 20% 10%
10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input
Applying additive resistance:
+V +
+
-V –
–
DIM+
Additive Resistance
DIM-
“DO NOT connect “DIM- to -V”
Output current (%)
100% 90% 80% 70% 60% 50% 40% 30% 20% 10%
10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N (N=driver quantity forsynchronizeddimmingoperation ) Dimming input: Additive resistance
File Name:LPF-16D-SPEC 2024-10-16
16W Constant Current Mode LED Driver
LPF-16D series
Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options.
N
L
Relay
Switch
Adjuster
10K/N~100K/N Ohms resistance 1~10V DC Voltage 10V PWM Signal
Brown Blue
AC/L AC/N
LPF-16D
DIM+ DIM-
V(-) V(+)
Purple Pink
Black Red
LED Lighting Fixture
Using a switch and relay can turn ON/OFF the lighting fixture.
File Name:LPF-16D-SPEC 2024-10-16
16W Constant Current Mode LED Driver
OUTPUT LOAD vs TEMPERATURE
LPF-16D series
LOAD (%)
THD LOAD (%)
100 80 60 40 20
-35 -30 -15
0
15
30
50
60
AMBIENT TEMPERATURE,Ta ()
70 (HORIZONTAL)
LOAD (%)
100 80 60 40 20
-35 -30 -15
0
15
30
50
65
70 (HORIZONTAL)
Tcase ()
STATIC CHARACTERISTIC
100 90 80 70 60 50 40
90 100 125 135 145 155 165 175 180 200 230 305
INPUT VOLTAGE (V) 60Hz De-rating is needed under low input voltage.
PF
POWER FACTOR (PF) CHARACTERISTIC
Tcase at 60
1.02 1
0.98
0.96
0.94 277V
0.92
0.9
230V
0.88
110V
0.86
0.84
0.82
50%
60%
70%
80%
90%
100%
(16W)
LOAD
TOTAL HARMONIC DISTORTION (THD)
48V Model, Tcase at 60
20%
18%
16%
14%
12%
10%
8%
6%
4%
2%
0%
50%
60%
70%
80%
90%
100%
LOAD
277VAC 230VAC 115VAC
EFFICIENCY(%)
EFFICIENCY vs LOAD
LPF-16D series possess superior working efficiency that up to 85% can be reached in field applications. 48V Model, Tcase at 60
100 90 80 70 60 50 40 30 20 10 0 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
LOAD
277V 230V 110V
File Name:LPF-16D-SPEC 2024-10-16
16W Constant Current Mode LED Driver
LIFE TIME
LPF-16D series
LIFETIME(Kh)
120
100
80
60
40
20
0
20
30
40
50
60
70
Tcase ( )
File Name:LPF-16D-SPEC 2024-10-16
16W Constant Current Mode LED Driver
MECHANICAL SPECIFICATION
LPF-16D series
CASE NO.: LPF-16A Unit:mm Tolerance:±1
AC/N(Blue) AC/L(Brown)
300±20 SJOW 17AWG×2C & H05RN-F 2×1.0mm2
148 3.5
3.6
3.6
tc
60
3.5
tc : Max. Case Temperature
300±20 SJTW 18AWG*4C
+V(Red) -V(Black) DIM+(Purple) DIM-(Pink)
3.5 40
13 3.5
32
Recommend Mounting Direction
INSTALLATION MANUAL
Please refer to:http://www.meanwell.com/manual.html
File Name:LPF-16D-SPEC 2024-10-16
Documents / Resources
 |
MEAN WELL LPF-16D Series 16W Constant Current Mode LED Driver [pdf] Owner's Manual LPF-16D Series 16W Constant Current Mode LED Driver, LPF-16D Series, 16W Constant Current Mode LED Driver, Current Mode LED Driver, LED Driver, Driver |
