HVGC-100 Series 100W Constant Current Mode LED Driver
“
Specifications
- Model: HVGC-100-350, HVGC-100-700
- Output:
- Rated Current: 350mA, 700mA
- Rated Power: 99.75W, 99.4W
- Constant Current Region: 29 ~ 285V
- Current Adjustment Range: 210 ~ 350mA, 420 ~ 700mA
- Voltage Range: 180 ~ 528VAC, 254VDC ~ 747VDC
- Input:
- Frequency Range: 47 ~ 63Hz
- Power Factor (Typ.): PF0.98/230VAC, PF0.98/277VAC,
PF0.97/347VAC, PF0.93/480VAC @ full load
- Efficiency (Typ.): 91%
- Working Temperature: Refer to the warranty statement on MEAN
WELL’s website
Product Usage Instructions
Installation
- Ensure input power is within specified voltage range.
- Connect AC/L to Brown wire, AC/N to Blue wire, DIM+ to Purple
wire, DIM- to Pink wire, -V to Black wire, and +V to Red wire. - Refer to the block diagram for correct wiring.
Operation
- This LED driver operates in constant current mode to drive LEDs
directly. - The output voltage depends on the end system configuration
within the constant current region. - Contact MEAN WELL for compatibility issues.
FAQ
Q: What is the maximum number of units that can be connected to
a 16A circuit breaker?
A: At 480VAC, you can connect up to 5 units with a circuit
breaker of type B or up to 8 units with a circuit breaker of type
C.
Q: Is the LED driver suitable for dimming operation?
A: Yes, the HVGC-100 series features a 3-in-1 dimming function
for B/AB-Type LEDs.
“`
100W Constant Current Mode LED Driver
HVGC-100 series
User’s Manual
IP65 IP67
Bauart gepruft Sicherheit
egelma ge od o s be wac g www.tuv.com ID 2000000000
~
A
D
File Name:HVGC-100-SPEC 2024-07-19
100W Constant Current Mode LED Driver
HVGC-100 series
SPECIFICATION
MODEL
HVGC-100-350
HVGC-100-700
OUTPUT
RATED CURRENT
350mA
RATED POWER
99.75W
CONSTANT CURRENT REGION Note.2 29 ~ 285V
CURRENT ADJ. RANGE
Adjustable for A/AB-Type only (via built-in potentiometer) 210 ~ 350mA
CURRENT RIPPLE Note.5 5.0% max. @rated current
CURRENT TOLERANCE
±5.0%
SET UP TIME
Note.4 500ms, 80ms /230VAC, 347VAC, 480VAC
700mA 99.4W 15 ~ 142V
420 ~ 700mA
VOLTAGE RANGE
180 ~ 528VAC 254VDC ~ 747VDC Note.3 (Please refer to “STATIC CHARACTERISTIC” section)
FREQUENCY RANGE POWER FACTOR (Typ.)
47 ~ 63Hz PF0.98/230VAC, PF0.98/277VAC, PF0.97/347VAC, PF0.93/480VAC @full load (Please refer to “POWER FACTOR (PF) CHARACTERISTIC” section)
INPUT
TOTAL HARMONIC DISTORTION
THD< 20%(@ load50%/230VAC, 277VAC, 347VAC; @ load75%/480VAC) (Please refer to “TOTAL HARMONIC DISTORTION (THD)” section)
EFFICIENCY (Typ.)
91%
91%
AC CURRENT (Typ.)
0.38A / 347VAC 0.28A / 480VAC
INRUSH CURRENT (Typ.)
COLD START 25A(twidth=900s measured at 50% Ipeak) at 480VAC; Per NEMA 410
MAX. No. of PSUs on 16A CIRCUIT BREAKER
5 units (circuit breaker of type B) / 8 units (circuit breaker of type C) at 480VAC
LEAKAGE CURRENT SHORT CIRCUIT
PROTECTION OVER VOLTAGE
OVER TEMPERATURE
WORKING TEMP.
MAX. CASE TEMP.
ENVIRONMENT
WORKING HUMIDITY STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
<0.75mA / 480VAC
Constant current limiting, recovers automatically after fault condition is removed
300 ~ 320V
150 ~ 160V
Shut down o/p voltage with auto-recovery or re-power on to recovery
Shut down o/p voltage, recovers automatically after temperature goes down
Tcase=-40 ~ +90(Please refer to “OUTPUT LOAD vs TEMPERATURE” section)
Tcase=+90
20 ~ 95% RH non-condensing
-40 ~ +80, 10 ~ 95% RH
±0.03%/ (0 ~ 60)
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
SAFETY STANDARDS
UL8750, CSA C22.2 No. 250.0-08, TUV BS EN/EN61347-1, BS EN/EN61347-2-13, EAC TP TC 004, IP65 or IP67 approved; design refer to UL60950-1
SAFETY & WITHSTAND VOLTAGE
EMC
ISOLATION RESISTANCE
EMC EMISSION
I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25/ 70% RH Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C (@ load50%) ; BS EN/EN61000-3-3, FCC Part 15 Subpart, EAC TP TC 020
EMC IMMUNITY
Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN61547, light industry level (surge immunity Line-Earth 4KV, Line-Line 2KV), EAC TP TC 020
OTHERS NOTE
MTBF
745.0K hrs min. Telcordia SR-332 (Bellcore) ; 186.1K hrs min. MIL-HDBK-217F (25)
DIMENSION
236*68*38.8mm (L*W*H)
PACKING
1.18Kg; 12pcs/15.2Kg/0.74CUFT
1. All parameters NOT specially mentioned are measured at 347VAC input, rated current and 25 of ambient temperature.
2. Please refer to “DRIVING METHODS OF LED MODULE”.
3. De-rating may be needed under low input voltages. Please refer to “STATIC CHARACTERISTIC” sections for details.
4. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time.
5. It is measured 50% ~ 100% of maximum voltage under rated power delivery.
6. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
(as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf)
7. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED driver can only be used behind a switch without permanently
connected to the mains.
8. This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 80 or less.
9. Please refer to the warranty statement on MEAN WELL’s website at http://www.meanwell.com.
10. The ambient temperature derating of 3.5/1000m with fanless models and of 5/1000m with fan models for operating altitude higher than 2000m(6500ft).
11. For any application note and IP water proof function installation caution, please refer our user manual before using.
https://www.meanwell.com/Upload/PDF/LED_EN.pdf
Product Liability DisclaimerFor detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx
File Name:HVGC-100-SPEC 2024-07-19
100W Constant Current Mode LED Driver
Block Diagram
EMI FILTER
I/P
&
RECTIFIERS
FG
PFC CIRCUIT
POWER SWITCHING
PFC CONTROL
O.L.P. O.T.P.
PWM & PFC CONTROL
HVGC-100 series
fosc : 80KHz
RECTIFIERS &
FILTER
O.L.P.
DETECTION CIRCUIT
O.V.P.
+V
-V
DIM+ DIM(B Type)
DRIVING METHODS OF LED MODULE
This series works in constant current mode to directly drive the LEDs.
In the constant current region, the highest voltage at the output of the driver
100
depends on the configuration of the end systems.
Should there be any compatibility issues, please contact MEAN WELL.
Vo(%)
Constant Current region
50
100
Io (%)
Typical output current normalized by rated current (%)
File Name:HVGC-100-SPEC 2024-07-19
100W Constant Current Mode LED Driver
DIMMING OPERATION
FG (Green/Yellow)
AC/L(Brown) AC/N(Blue)
HVGC-100
HVGC-100 series
DIM+(Purple) DIM-(Pink) -V(Black) +V(Red)
3 in 1 dimming function (for B/AB-Type)
Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-:
0 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: 100A (typ.)
Applying additive 0 ~ 10VDC
100%
90%
+V +
80%
+
70%
Output current (%)
-V
60%
–
50%
DIM+ +
40%
Additive Voltage
30%
–
20%
DIM-
10%
“DO NOT connect “DIM- to -V”
0% 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V
Dimming input: Additive voltage
Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz):
+V +
+
-V
–
DIM+
Additive PWM signal DIM-
“DO NOT connect “DIM- to -V”
Output current (%)
100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0%
0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input
Applying additive resistance:
100%
Output current (%)
+V +
-V DIM+
90%
+
80%
70%
–
60%
50%
40%
Additive Resistance
30%
DIM-
20%
“DO NOT connect “DIM- to -V”
10%
0% Short 10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N
(N=driver quantity for synchronized dimming operation)
Dimming input: Additive resistance
Note : 1. Min. dimming level is about 8% and the output current is not defined when 0%< Iout<8%. 2. The output current could drop down to 0% when dimming input is about 0k or 0Vdc, or 10V PWM signal with 0% duty cycle.
File Name:HVGC-100-SPEC 2024-07-19
100W Constant Current Mode LED Driver
OUTPUT LOAD vs TEMPERATURE(Note.9)
HVGC-100 series
LOAD (%)
LOAD (%)
100
100
80
80
LOAD (%)
60
60
40
40
20
20
-40 -25 -10
0
15
30
50
60
AMBIENT TEMPERATURE,Ta ()
70 (HORIZONTAL)
-40 -25 0
20
45
55
65
75
90 (HORIZONTAL)
Tcase ()
STATIC CHARACTERISTIC
100 90 80 70 60 50 40
180 200
347
440
480
528
INPUT VOLTAGE (V) 60Hz
De-rating is needed under low input voltage.
TOTAL HARMONIC DISTORTION (THD)
700mA Model, Tcase at 80
20.00 18.00 16.00 14.00 12.00 10.00
8.00 6.00 4.00 2.00 0.00
50% 60% 70% 80%
LOAD
347VAC 480VAC 277VAC 230VAC
90% 100%
EFFICIENCY(%)
PF
POWER FACTOR (PF) CHARACTERISTIC
Tcase at 80
1 .0 0
0 .9 8
0 .9 6
0 .9 4
0 .9 2
0 .9 0
0 .8 8
0 .8 6
0 .8 4
0 .8 2
0 .8 0
50%
60%
70%
80%
LOAD
90%
100% (100W)
480V 347V 277V 230V
EFFICIENCY vs LOAD
HVGC-100 series possess superior working efficiency that up to 91% can be reached in field applications. 700mA Model, Tcase at 80
0.94 0.90 0.86 0.82 0.78 0.74 0.70 0.66 0.62 0.58
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
480V 347V 277V 230V
LOAD
File Name:HVGC-100-SPEC 2024-07-19
THD(%)
100W Constant Current Mode LED Driver
HVGC-100 series
LIFETIME
LIFETIME(Kh)
120
100
80
60
40
20
0
20
30
40
50
60
70
80
90
Tcase( )
File Name:HVGC-100-SPEC 2024-07-19
100W Constant Current Mode LED Driver
HVGC-100 series
MECHANICAL SPECIFICATION
A-Type
Case No. 994 Unit:mm Tolerance:±1
FG (Green/Yellow)
AC/L(Brown) AC/N(Blue)
9.4 34.2 9.4 68
34
12 9.6
300±20 STW 18AWG×3C
236 212
T case tc
tc : Max. Case Temperature
104.4
Io
ADJ.
300±20
SJTW 18AWG×2C
4.2×4PL
-V(Black) +V(Red)
38.8
B-Type
FG (Green/Yellow) AC/L(Brown) AC/N(Blue)
12 9.6
300±20 STW 18AWG×3C
236 212
T case tc
104.4
9.4 34.2 9.4 68
34
tc : Max. Case Temperature
300±20 UL2517 18AWG×2C
SJTW 18AWG×2C
4.2×4PL
DIM+(Purple) DIM-(Pink)
-V(Black) +V(Red)
38.8
File Name:HVGC-100-SPEC 2024-07-19
100W Constant Current Mode LED Driver
HVGC-100 series
AB-Type
FG (Green/Yellow)
AC/L(Brown) AC/N(Blue)
9.4 34.2 9.4 68
34
12 9.6
300±20 STW 18AWG×3C
236 212
T case tc
tc : Max. Case Temperature
104.4
Io
300±20
ADJ.
UL2517 18AWG×2C
SJTW 18AWG×2C
4.2×4PL
DIM+(Purple) DIM-(Pink)
-V(Black) +V(Red)
38.8
D-Type
FG (Green/Yellow) AC/L(Brown) AC/N(Blue)
9.4 34.2 9.4 68
34
12 9.6
300±20 STW 18AWG×3C
236 212
T case tc
104.4
tc : Max. Case Temperature
300±20 SJTW 18AWG×2C 4.2×4PL
-V(Black) +V(Red)
38.8
File Name:HVGC-100-SPEC 2024-07-19
100W Constant Current Mode LED Driver
HVGC-100 series
WATERPROOF CONNECTION
Waterproof connector Waterproof connector can be assembled on the output cable of HVGC-100 to operate in dry/wet/damp or outdoor environment.
AC
source
I/P
HVGC-100
O/P
Size
Pin Configuration (Female)
Size
Pin Configuration (Female)
M12
Order No. Suitable Current
4-PIN 5A/PIN M12-04 10A max.
Cable Joiner
66 26 20
5-PIN 5A/PIN M12-05 10A max.
M15
Order No. Suitable Current
2-PIN 12A/PIN M15-02 12A max.
CJ04-1 suitable for 14AWG~16AWG CJ04-2 suitable for 18AWG~22AWG
LED Lamp
Up to four wires can be connected through this cable joiner by soldering or clamping by tools.
25 68 61 8.5 32 8.5 6 35 38.8
HVGC-100
O/P Wires
CJ04 cable joiner can be purchased independently for user’s own assembly. MEAN WELL order No. : CJ04-1, CJ04-2.
Junction Box Option
212 374
FG (Green/Yellow) AC/L(Brown) AC/N(Blue)
STW 18AWG×3C
3- PF 1/2″ 150±20
Junction box option is available for A – Type. Please contact MEAW WELL for details.
INSTALLATION MANUAL
Please refer to : http://www.meanwell.com/manual.html
LED Lamp
76
10
5
3- PF 1/2″ 150±20
-V(Black) +V(Red) SVT 18AWG×2C
2-5
86
File Name:HVGC-100-SPEC 2024-07-19
Documents / Resources
 |
MEAN WELL HVGC-100 Series 100W Constant Current Mode LED Driver [pdf] Owner's Manual HVGC-100-350, HVGC-100-700, HVGC-100 Series 100W Constant Current Mode LED Driver, HVGC-100 Series, 100W Constant Current Mode LED Driver, Constant Current Mode LED Driver, Current Mode LED Driver, Mode LED Driver, LED Driver, Driver |