HLG-185H-C Series Constant Current Mode LED Driver
“
Product Specifications
- Model: HLG-185H-C500, HLG-185H-C700,
HLG-185H-C1050, HLG-185H-C1400 - Rated Current: 500mA, 700mA, 1050mA,
1400mA - Rated Power: 200W
- Constant Current Region: 200V ~ 400V, 143V ~
286V, 95V ~ 190V, 71V ~ 143V - Output Current Adj. Range: Can be adjusted by
internal potentiometer (A/AB type only) - Input Voltage Range: 90 ~ 305VAC, 127 ~
431VDC - Frequency Range: 47 ~ 63Hz
- Efficiency (Typ.): 94%
Product Usage Instructions
Installation
1. Ensure the power source matches the input voltage range
specified for the LED driver.
2. Connect the driver to the LED module following the correct
polarity.
Adjusting Output Current
1. For HLG-185H-C500, adjust the output current between 250mA
and 500mA using the internal potentiometer.
2. Repeat the same process for other models within their
specified current ranges.
Dimming Operation
1. Use the DIM+ and DIM- terminals for dimming functionality.
Apply one of the three methodologies: 1 ~ 10VDC, 10V PWM signal, or
resistance.
Frequently Asked Questions (FAQ)
1. How do I know if there are compatibility issues with my LED
system?
If you encounter any compatibility issues with your LED system,
please contact MEAN WELL for assistance.
2. Can I adjust the output current for all models?
The output current can be adjusted using the internal
potentiometer, but this feature is available only for A/AB type
drivers.
3. What is the dimming function of the HLG-185H-C series?
The HLG-185H-C series offers a 3-in-1 dimming function that
allows adjustment of the constant current level through various
methodologies.
“`
200W Constant Current Mode LED Driver
HLG-185H-C series
User’s Manual
IP65 IP67
~
A
Downloaded from Arrow.com.
File Name:HLG-185H-C-SPEC 2025-01-09
200W Constant Current Mode LED Driver
HLG-185H-C series
SPECIFICATION
MODEL
HLG-185H-C500
HLG-185H-C700
HLG-185H-C1050
HLG-185H-C1400
RATED CURRENT
500mA
700mA
1050mA
1400mA
RATED POWER
200W
200.2W
199.5W
200.2W
CONSTANT CURRENT REGION Note.2 200V ~ 400V
143V ~ 286V
95V ~ 190V
71V ~ 143V
OUTPUT CURRENT ADJ. RANGE
Can be adjusted by internal potentiometer (A/AB type only)
250 ~ 500mA
350 ~ 700mA
525 ~ 1050mA
700 ~ 1400mA
CURRENT RIPPLE CURRENT TOLERANCE
5.0% max. @rated current ±5%
SET UP TIME
Note.4 1000ms/115VAC 500ms/230VAC
VOLTAGE RANGE
90 ~ 305VAC 127 ~ 431VDC Note.3 (Please refer to “STATIC CHARACTERISTIC” section)
FREQUENCY RANGE
47 ~ 63Hz
POWER FACTOR (Typ.)
PF0.98/115VAC or PF0.96/230VAC or PF0.93/277VAC @full load (Please refer to “POWER FACTOR (PF) CHARACTERISTIC” section)
INPUT
TOTAL HARMONIC DISTORTION
THD< 20%@50% load/115VAC, or 230VAC, or @75% load/277VAC (Please refer to “TOTAL HARMONIC DISTORTION” section)
EFFICIENCY (Typ.)
94%
94%
94%
94%
AC CURRENT (Typ.) INRUSH CURRENT(Typ.)
2A / 115VAC
1A / 230VAC
0.85A / 277VAC
COLD START 55A(twidth=900s measured at 50% Ipeak) at 230VAC; Per NEMA 410
MAX. No. of PSUs on 16A CIRCUIT BREAKER
2 units (circuit breaker of type B) / 3 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT
<0.75mA / 277VAC
SHORT CIRCUIT
Constant current limiting, recovers automatically after fault condition is removed
PROTECTION OVER VOLTAGE
450 ~ 470V
320 ~ 340V
210 ~ 225V
Shut down o/p voltage with auto-recovery or re-power on to recovery
160 ~ 170V
OVER TEMPERATURE Note.7 Shut down o/p voltage, recovers automatically after temperature goes down
WORKING TEMP. MAX. CASE TEMP.
Tcase=-40 ~ +90(Refer to “Derating Curve”) Tcase=+90
ENVIRONMENT WORKING HUMIDITY STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT
10 ~ 95% RH non-condensing -40 ~ +80, 10 ~ 95% RH ±0.03%/ (0 ~ 50)
VIBRATION
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes;
SAFETY STANDARDS
SAFETY & EMC
WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION
EMC IMMUNITY MTBF
UL8750, CSA C22.2 No. 250.13-12, BS EN/EN/AS/NZS 61347-1, BS EN/EN/AS/NZS 61347-2-13, BS EN/EN62384 independent, GB19510.1,GB19510.14;IP65 or IP67, J61347-1, J61347-2-13, EAC TP TC 004 approved
I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25/ 70% RH Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C (50% load) ; BS EN/EN61000-3-3,GB/T 17743 , GB17625.1, EAC TP TC 020
Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN61547, heavy industry level (surge immunity Line-Earth 4KV, Line-Line 2KV), EAC TP TC 020
2458.6K hrs min. Telcordia SR-332 (Bellcore) ; 191.9K hrs min. MIL-HDBK-217F (25)
OTHERS DIMENSION
228*68*38.8mm (L*W*H)
NOTE
PACKING
1.15Kg; 12pcs/14.8Kg/0.8CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25 of ambient temperature.
2. Please refer to “DRIVING METHODS OF LED MODULE”.
3. De-rating may be needed under low input voltages. Please refer to “STATIC CHARACTERISTIC” sections for details.
4. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time. 5. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
(as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf)
6. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED driver can only be used behind a switch without permanently
connected to the mains.
7. For OTP which triggered at light load/no load condition, proceed AC repower on to recovery. 8. This series meets the typical life expectancy of >62,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 75 or less.
9. Please refer to the warranty statement on MEAN WELL’s website at http://www.meanwell.com. 10. The ambient temperature derating of 3.5/1000m with fanless models and of 5/1000m with fan models for operating altitude higher than 2000m(6500ft).
11. For any application note and IP water proof function installation caution, please refer our user manual before using.
https://www.meanwell.com/Upload/PDF/LED_EN.pdf
Product Liability DisclaimerFor detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx
File Name:HLG-185H-C-SPEC 2025-01-09
Downloaded from Arrow.com.
200W Constant Current Mode LED Driver
BLOCK DIAGRAM
EMI FILTER
I/P
&
RECTIFIERS
FG
PFC CIRCUIT
POWER SWITCHING
O.T.P.
O.L.P.
PWM & PFC CONTROL
HLG-185H-C series
PFC fosc : 70KHz PWM fosc : 60KHz
RECTIFIERS &
FILTER
O.L.P.
DETECTION CIRCUIT
O.V.P.
+V
-V
DIM+ DIM(B Type)
DRIVING METHODS OF LED MODULE
This series works in constant current mode to directly drive the LEDs.
In the constant current region, the highest voltage at the output of the driver
100
depends on the configuration of the end systems.
Should there be any compatibility issues, please contact MEAN WELL.
Constant Current area
50
Vo(%)
50
100
Io (%)
Typical output current normalized by rated current (%)
Downloaded from Arrow.com.
File Name:HLG-185H-C-SPEC 2025-01-09
200W Constant Current Mode LED Driver
HLG-185H-C series
DIMMING OPERATION
FG (Green/Yellow)
AC/L(Brown) AC/N(Blue)
HLG-185H-C
DIM+(Purple) DIM-(Pink)
-V(Blue) +V(Brown)
3 in 1 dimming function (for B/AB-Type)
Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 1 ~ 10VDC, or 10V PWM signal or resistance.
Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: 100A (typ.)
Applying additive 1 ~ 10VDC
100%
+V +
90%
+
80%
Output current (%)
-V
70%
–
60%
DIM+ +
50%
Additive Voltage
40%
–
30%
DIM-
20%
“DO NOT connect “DIM- to -V”
10% 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V
Dimming input: Additive voltage
Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz):
+V +
+
-V
–
DIM+
Additive PWM signal DIM-
“DO NOT connect “DIM- to -V”
Output current (%)
100% 90% 80% 70% 60% 50% 40% 30% 20% 10%
10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input
Applying additive resistance:
+V +
+
-V
–
DIM+
Additive Resistance DIM-
“DO NOT connect “DIM- to -V”
Output current (%)
100% 90% 80% 70% 60% 50% 40% 30% 20% 10%
10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N (N=driver quantity for synchronized dimming operation) Dimming input: Additive resistance
Downloaded from Arrow.com.
File Name:HLG-185H-C-SPEC 2025-01-09
200W Constant Current Mode LED Driver
HLG-185H-C series
Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options.
N FG L
Relay
Switch
Adjuster
10K/N~100K/N Ohms resistance 1~10V DC Voltage 10V PWM Signal
Green/ Yellow
Brown
Blue
AC/L AC/N
HLG-185H-C B-Type
DIM+ DIM-
V(-) V(+)
Purple Pink
Blue Brown
LED Lighting Fixture
Using a switch and relay can turn ON/OFF the lighting fixture.
Downloaded from Arrow.com.
File Name:HLG-185H-C-SPEC 2025-01-09
LOAD (%)
200W Constant Current Mode LED Driver
OUTPUT LOAD vs TEMPERATURE(Note.8)
HLG-185H-C series
100
100
80
80
LOAD (%)
60
60
40
40
20
20
-40 -20 -10
0
15
30
50
60
AMBIENT TEMPERATURE,Ta ()
70 (HORIZONTAL)
-40 -20
0
20
45
55
65
75
90 (HORIZONTAL)
Tcase ()
STATIC CHARACTERISTIC
100 90 80 70 60 50 40
90 100 125 135 145 155 165 175 180 200 230 305
INPUT VOLTAGE (V) 60Hz
PF
POWER FACTOR (PF) CHARACTERISTIC
Tcase at 80
1 0 .9 8 0 .9 6 0 .9 4 0 .9 2
0 .9 0 .8 8 0 .8 6
50%
60%
70%
80%
LOAD
277V 230V 115V
90%
100% (200W()250W)
TOTAL HARMONIC DISTORTION (THD)
700mA Model, Tcase at 80
25
20
15
277VAC
10
230VAC
115VAC 5
0
50%
60%
70%
80%
90%
100%
LOAD
EFFICIENCY(%)
EFFICIENCY vs LOAD
HLG-185H-C series possess superior working efficiency that up to 94% can be reached in field applications. 700mA Model, Tcase at 80
95 93 91 89 87 85 83 81 79 77
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
LOAD
277V 230V 115V
LOAD (%)
THD(%)
Downloaded from Arrow.com.
File Name:HLG-185H-C-SPEC 2025-01-09
200W Constant Current Mode LED Driver
HLG-185H-C series
LIFE TIME
LIFETIME(Kh)
120
100
80
60
40
20
0
20
30
40
50
60
70
80
90
Tcase ( )
Downloaded from Arrow.com.
File Name:HLG-185H-C-SPEC 2025-01-09
200W Constant Current Mode LED Driver
MECHANICAL SPECIFICATION
A-Type
228
12
204
9.6
300±20
FG (Green/Yellow)
AC/L(Brown)
tc
AC/N(Blue)
SJOW 17AWG&H05RN-F 1.0mm²x3C
9.4 34.2 9.4 68
34
tc : Max. Case Temperature
HLG-185H-C series
Case No.994D Unit:mm Tolerance:±1
Io ADJ.
102
300±20
-V(Blue)
SOOW 17AWG&H07RN-F 1.0mm²x2C +V(Brown) (for HLG-185H-C500)
SJ4O.2W×147PALWG&H05RN-F 1.0mm²x2C(for others)
38.8
9.4 34.2 9.4 68
34
B-Type
12 9.6
300±20
FG (Green/Yellow)
AC/L(Brown)
AC/N(Blue)
SJOW 17AWG&H05RN-F 1.0mm²x3C
228 204
tc
102
tc : Max. Case Temperature
300±20
SJOW 17AWG&H05RN-F 1.0mm²x2C
DIM+(Purple) DIM-(Pink)
-V(Blue)
SOOW 17AWG&H07RN-F 1.0mm²x2C +V(Brown) (for HLG-185H-C500)
S4J.O2×W41P7LAWG&H05RN-F 1.0mm²x2C(for others)
38.8
Downloaded from Arrow.com.
File Name:HLG-185H-C-SPEC 2025-01-09
200W Constant Current Mode LED Driver
HLG-185H-C series
AB-Type
228
12
204
9.6
300±20
FG (Green/Yellow)
AC/L(Brown)
tc
AC/N(Blue)
SJOW 17AWG&H05RN-F 1.0mm²x3C
9.4 34.2 9.4 68
34
tc : Max. Case Temperature
300±20
Io ADJ.
SJOW 17AWG&H05RN-F 1.0mm²x2C
DIM+(Purple)
102
DIM-(Pink)
-V(Blue)
SOOW 17AWG&H07RN-F 1.0mm²x2C +V(Brown) (for HLG-185H-C500)
S4J.O2×W41P7LAWG&H05RN-F 1.0mm²x2C(for others)
38.8
D-Type
FG (Green/Yellow)
AC/L(Brown) AC/N(Blue)
12 9.6 300±20
SJOW 17AWGx3C
228 204
T case tc
102
9.4 34.2 9.4 68
34
tc : Max. Case Temperature
300±20
-V(Blue) +V(Brown)
SOOW 17AWG&H07RN-F 1.0mm²x2C (for HLG-185H-C500)
SJ4O.2W×147PALWG&H05RN-F 1.0mm²x2C(for others)
38.8
Downloaded from Arrow.com.
File Name:HLG-185H-C-SPEC 2025-01-09
200W Constant Current Mode LED Driver
HLG-185H-C series
WATERPROOF CONNECTION
Waterproof connector Waterproof connector can be assembled on the output cable of HLG-185H-C to operate in dry/wet/damp or outdoor environment.
AC source
I/P
HLG-185H-C
O/P
Size
Pin Configuration (Female)
Size
Pin Configuration (Female)
M12
Order No. Suitable Current
4-PIN 5A/PIN M12-04 10A max.
Cable Joiner
66 26 20
5-PIN 5A/PIN M12-05 10A max.
M15
Order No. Suitable Current
2-PIN 12A/PIN M15-02 12A max.
CJ04-1 suitable for 14AWG~16AWG CJ04-2 suitable for 18AWG~22AWG
LED Lamp
25
Up to four wires can be connected through this cable joiner by soldering or clamping by tools.
HLG-185H-C
O/P Wires
CJ04 cable joiner can be purchased independently for user’s own assembly. MEAN WELL order No. : CJ04-1, CJ04-2.
INSTALLATION MANUAL
Please refer to : http://www.meanwell.com/manual.html
LED Lamp
Downloaded from Arrow.com.
File Name:HLG-185H-C-SPEC 2025-01-09
Documents / Resources
 |
MEAN-WELL HLG-185H-C Series Constant Current Mode LED Driver [pdf] Owner's Manual HLG-185H-C500, HLG-185H-C700, HLG-185H-C1050, HLG-185H-C1400, HLG-185H-C Series Constant Current Mode LED Driver, HLG-185H-C Series, Constant Current Mode LED Driver, Current Mode LED Driver, Mode LED Driver, LED Driver |