MEAN WELL HBG-200 Series Constant Voltage Constant Current LED Driver Owner's Manual

HBG-200 series is a 200W AC/DC LED driver featuring the circular shape design. It operates from 90~305VAC and offers the dual modes constant voltage and constant current output models with different rated voltage between 36Vand 60V. Thanks to the high efficiency up to 93.5%,with the fanless design, the entire series is able to operate for -40°C ~ +85°C case temperature under free air convection. The design of metal housing and IP67/1P65 ingress protection level allows this series to fit both indoor and outdoor applications. HBG-200 is equipped with various function options, such as dimming methodologies, so as to provide the optimal design flexibility for LED lighting system.

Model Encoding

Function mode option

Rated output voltage(36/48/60V)
Rated wattage

Series name

Type	IP Level	Function	Note
Blank	IP67	lo fixed.	In Stock
A	IP65	lo adjustable through built-in potentiometer.	In Stock
B	IP67	3 in 1 dimming function (0-10Vdc, 10V PWM signal and resistance)	In Stock
AB	IP65	lo adjustable through built-in potentiometer with 3 in 1 dimming function	In Stock
DA	IP67	DALI control technology.	In Stock

SPECIFICATION

MODEL		HBG-200-36	HBG-200-48	HBG-200-60
OUTPUT	DC VOLTAGE	36V	48V	60V
	CONSTANT CURRENT REGION Note.2	21.6 ~ 36V	28.8 ~ 48V	36 ~ 60V
	RATED CURRENT	5.5A	4.1A	3.3A
	RATED POWER	198W	196.8W	198W
	RIPPLE & NOISE (max.) Note.3	250mVp-p	250mVp-p	350mVp-p
	CURRENT ADJ. RANGE	Adjustable for A-Type and AB-Type (via built-in potentiometer)
		3.3 ~ 5.5A	2.46 ~ 4.1A	1.98 ~ 3.3A
	VOLTAGE TOLERANCE Note.4	±2.0%
	LINE REGULATION	±0.5%
	LOAD REGULATION	±1.0%
	SETUP, RISE TIME Note.6	2500ms,200ms /115VAC 500ms,200ms /230VAC
	HOLD UP TIME (Typ.)	12ms /115VAC, 230VAC
INPUT	VOLTAGE RANGE Note.5	90 ~ 305VAC 127~417VDC (Please refer to “STATIC CHARACTERISTIC” section)
	FREQUENCY RANGE	47 ~ 63Hz
	POWER FACTOR	PF>0.98/115VAC, PF>0.95/230VAC, PF>0.92/277VAC@full load (Please refer to “POWER FACTOR (PF) CHARACTERISTIC” section)
	TOTAL HARMONIC DISTORTION	THD< 20%(@load≧60%/115VC,230VAC; @load≧75%/277VAC) (Please refer to “TOTAL HARMONIC DISTORTION(THD)” section)
	EFFICIENCY (Typ.)	92%	93%	93.5%
	AC CURRENT (Typ.)	1.9A / 115VAC 1A / 230VAC 0.9A / 277VAC
	INRUSH CURRENT (Typ.)	COLD START 85A(twidth=600μs measured at 50% Ipeak) at 230VAC; Per NEMA 410
	MAX. No. of PSUs on 16A CIRCUIT BREAKER	4 units (circuit breaker of type B) / 7 units (circuit breaker of type C) at 230VAC
	LEAKAGE CURRENT	<0.75mA / 277VAC
	NO LOAD / STANDBY POWER CONSUMPTION	Standby power consumption <0.5W for B/AB/DA-Type Blank/A-Type please refer to Note.8
PROTECTION	OVER CURRENT	95~108%
		Constant current limiting, recovers automatically after fault condition is removed
	SHORT CIRCUIT	Hiccup mode or constant current limiting, recovers automatically after fault condition is removed
	OVER VOLTAGE	41 ~ 47V	54 ~ 62V	65 ~ 75V
		Shut down o/p voltage with auto-recovery or re-power on to recovery
	OVER TEMPERATURE	Shut down o/p voltage, recovers automatically after temperature goes down
ENVIRONMENT	WORKING TEMP.	Tcase=-40 ~ +85℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)
	MAX. CASE TEMP.	Tcase=+85℃
	WORKING HUMIDITY	20 ~ 95% RH non-condensing
	STORAGE TEMP., HUMIDITY	-40 ~ +80℃, 10 ~ 95% RH
	TEMP. COEFFICIENT	±0.03%/℃ (0 ~ 50℃)
	VIBRATION	10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
SAFETY & EMC	SAFETY STANDARDS	UL8750(type”HL”),CSA C22.2 No.250.13-12,ENEC BS EN/EN61347-1,BS EN/EN61347-2-13 independent, BS EN/EN62384; GB19510.14, GB19510.1; EAC TP TC 004,IP65 or IP67 approved
	DALI STANDARDS	Compliance to IEC62386-101, 102, 207 for DA type only
	WITHSTAND VOLTAGE	I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
	ISOLATION RESISTANCE	I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH
	EMC EMISSION	Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C (@load≧60%) ; BS EN/EN61000-3-3; GB17625.1, GB17743,EAC TP TC 020
	EMC IMMUNITY	Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN61547,light industry level (surge immunity:Line-Earth:4KV,Line-Line:2KV),EAC TP TC 020
OTHERS	MTBF	2042.7K hrs min. Telcordia SR-332 (Bellcore) ;207.4K hrs min. MIL-HDBK-217F (25℃)
	DIMENSION	Refer to mechanical specification
	PACKING	1.53Kg; 8pcs/13.8Kg/1.61CUFT
NOTE	All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25°C of ambient temperature. Please refer to “DRIVING METHODS OF LED MODULE”. Ripple & noise are measured at 20MHz of bandwidth by using a 12″ twisted pair-wire terminated with a 0.1 uf & 47uf parallel capacitor. Tolerance : includes set up tolerance, line regulation and load regulation. De-rating may be needed under low input voltages. Please refer to “STATIC CHARACTERISTIC” sections for details. Length of set up time is measured at cold first start. Turning ON/OFF the driver may lead to increase of the set up time. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED driver can only be used behind a switch without permanently connected to the mains. This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly point (or TMP, per DLC), is about 70°C or less. Please refer to the warranty statement on MEAN WELL’s website at http://www.meanwell.com The ambient temperature derating of 3.5°C/1000m with fanless models and of 5°C/1000m with fan models for operating altitude higher than 2000m(6500ft). For any application note and IP water proof function installation caution, please refer our user manual before using. https://www.meanwell.com/Upload/PDF/LED_EN.pdf Product Liability Disclaimer : For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx

BLOCK DIAGRAM

fosc : 100KHz

EMI FILTER & RECTIFIERS

PFC CIRCUIT
POWER SWITCHING

RECTIFIERS & FILTER
DETECTION CIRCUIT

PWM & PFC CONTROL

DRIVING METHODS OF LED MODULE

This series is able to work in either Constant Current mode (a direct drive way) or Constant Voltage mode (usually through additional DC/DC driver) to drive the LEDs.

(A)
Constant Voltage area
(B)
Constant Current area
(C)
Hiccup Protection
In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems.
Should there be any compatibility issues, please contact MEAN WELL.
Typical output current normalized by rated current (%)
Vo(%)

DIMMING OPERATION

* DIM+ for B/AB-Type
DA+ for DA-Type
* *DIM- for B/AB-Type
DA- for DA-Type

*DIM+(Purple)
**DIM-(Pink)
SVT 18AWG*2C
AC/L(Brown)
AC/N(Blue)
FG (Green/Yellow)

SVT 18AWG*2C
Vo+(Red)
Vo-(Black)

SJTW 18AWG*2C

3 in 1 dimming function (for B/AB-Type)
– Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 0 ~ 10VDC, or 10V PWM signal or resistance.
– Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers.
– Dimming source current from power supply: 100μA (typ.)

Applying additive 0 ~ 10VDC

Additive Voltage
“DO NOT connect “DIM- to -V”

Output current (%)
Dimming input: Additive voltage

Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz):

Additive PWM signal

“DO NOT connect” DIM- to -V”

Output current (%)

Duty cycle of additive 10V PWM signal dimming input

Applying additive resistance:

Additive Resistance
“DO NOT connect” DIM- to -V”

Output current (%)
(N=driver quantity for synchronized dimming operation)
Dimming input: Additive resistance

Note :

Min. dimming level is about 8% and the output current is not defined when 0%< Iout<8%.
The output current could drop down to 0% when dimming input is about 0kΩ or 0Vdc, or 10V PWM signal with 0% duty cycle.

Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options.

10K/N~100K/N Ohms resistance
1~10V DC Voltage
10V PWM Signal
LED Lighting Fixture

HBG-200
B-Type

Using a switch and relay can turn ON/OFF the lighting fixture.

DALI Interface (primary side; for DA-Type)

Apply DALI signal between DA+ and DA-.
DALI protocol comprises 16 groups and 64 addresses.
First step is fixed at 8% of output.

OUTPUT LOAD vs TEMPERATURE(Note.11)

LOAD (%)
AMBIENT TEMPERATURE (°C)

LOAD (%)
Tcase (°C)

STATIC CHARACTERISTIC

LOAD (%)
INPUT VOLTAGE (V) 60Hz

De-rating is needed under low input voltage.

POWER FACTOR (PF) CHARACTERISTIC

Tcase at 75°C

PF
LOAD

TOTAL HARMONIC DISTORTION (THD)

48V Model, Tcase at 75°C

THD
LOAD

EFFICIENCY vs LOAD

HBG-200 series possess superior working efficiency that up to 93.5% can be reached in field applications.
48V Model, Tcase at 75℃

EFFICIENCY(%)

LOAD

LIFETIME

LIFETIME(Kh)

Tcase (℃ )

MECHANICAL SPECIFICATION

Case No.211 Unit:mm

Blank-Type

M10*P1.5-18h

AC/L(Brown)
AC/N(Blue)
FG (Green/Yellow)

SJTW 18AWG*3C
SJTW 18AWG*2C
Vo+(Red)

Vo-(Black)

: Max. Case Temperature.(case temperature measured point)
Ta: Ambient Temperature measured point

A-Type

M10*P1.5-18h

AC/L(Brown)
AC/N(Blue)

FG (Green/Yellow)
SJTW 18AWG*3C
SJTW 18AWG*2C

Vo+(Red)
Vo-(Black)

: Max. Case Temperature.(case temperature measured point)
Ta: Ambient Temperature measured point

B/DA-Type

M10*P1.5-18h

* DIM+ for B-Type
DA+ for DA-Type
* *DIM- for B-Type
DA- for DA-Type

*DIM+(Purple)
**DIM-(Pink)

SVT 18AWG*2C
AC/L(Brown)
AC/N(Blue)

FG (Green/Yellow)
SJTW 18AWG*3C
SJTW 18AWG*2C

Vo+(Red)
Vo-(Black)

: Max. Case Temperature.(case temperature measured point)

Ta: Ambient Temperature measured point

AB-Type

M10*P1.5-18h

*DIM+(Purple)
**DIM-(Pink)
SVT 18AWG*2C
AC/L(Brown)
AC/N(Blue)
FG (Green/Yellow)
SJTW 18AWG*3C
SJTW 18AWG*2C
Vo+(Red)
Vo-(Black)

: Max. Case Temperature.(case temperature measured point)
Ta: Ambient Temperature measured point

INSTALLATIONS


Hanger	Chain	High Bay Light

Caution
Please inspect the appearance of the driver if the package is damaged. There should not be any cracks.
Please do not drop or bump the driver.
All screws including the suspension screw should be paired with a spring washer and locked tight.
The entire luminaire, including the driver, should be limited to 10Kg or less.
The luminaire should be cautiously protected from damage due to shock throughout packaging and transportation.
Please thoroughly follow the preceding cautionary notes to prevent the luminaire from falling, leading to injuries.

INSTALLATION MANUAL

Please refer to : http://www.meanwell.com/manual.html

File Name:HBG-200-SPEC 2022-03-16

Downloaded from Arrow.com.

Documents / Resources

MEAN WELL HBG-200 Series Constant Voltage Constant Current LED Driver [pdf] Owner's Manual
HBG-200 Series Constant Voltage Constant Current LED Driver, HBG-200 Series, Constant Voltage Constant Current LED Driver, Constant Current LED Driver, Current LED Driver, LED Driver, Driver

References

User Manual

200W Constant Voltage + Constant Current LED Driver

HBG-200 series

Features

Applications

GTIN CODE

Description