MEAN WELL ENP-360 Series 360W Level Ⅵ Desktop Type Power Supply Instruction Manual

ENP-360 series is a 360W desktop type power supply working perfectly for communication related applications. Observing the standard 7″ width size in the land mobile radio field, it provides the most frequently used voltage in the communication field. With the rugged mechanical design along with the high efficiency circuitry, it operates for the ambient temperature range -30 C -+70 C under free air convection.

Model Encoding

MODEL				ENP-360-12		ENP-360-24		ENP-360-48
OUTPUT	DC VOLTAGE			13.8V		27.6V		55.2V
	RATED CURRENT			26A		13A		6.5A
	CURRENT	RATED		0 ~ 26A		0 ~ 13A		0 ~ 6.5A
		PEAK	Note.2	32.6A		16.3A		8.2A
	WATTAGE	RATED		359W		359W		359W
		PEAK	Note.2	450W		450W		453W
	RIPPLE & NOISE (max.) Note.3			150mVp-p		150mVp-p		350mVp-p
	VOLTAGE ADJ. RANGE			11.5 ~ 15V		23.5 ~ 30V		47.5 ~ 58.8V
	VOLTAGE TOLERANCE Note.4			±1.0%		±1.0%		±1.0%
	LINE REGULATION Note.5			±0.5%		±0.5%		±0.5%
	LOAD REGULATION		Note.6	±2.0%		±1.0%		±0.5%
	SETUP, RISE TIME		Note.7	1000ms, 100ms at full load
	HOLD UP TIME (Typ.)			20ms at full load
INPUT	VOLTAGE RANGE		Note.8	90 ~ 264VAC	127 ~ 370VDC
	FREQUENCY RANGE			47 ~ 63Hz
	POWER FACTOR (Typ.)			PF>0.98/115VAC, PF>0.95/230VAC at full load
	EFFICIENCY (Typ.)			91%		93%		94%
	AC CURRENT (Typ.)			3.8A/115VAC	1.9A/230VAC
	INRUSH CURRENT (Typ.)			COLD START 60A at 230VAC
	LEAKAGE CURRENT			<3.5mA / 240VAC
	NO LOAD POWER CONSUMPTION			<0.5W
PROTECTION	SHORT CIRCUIT			Protection type : Constant current limiting, recovers automatically after fault condition is removed
	OVERLOAD			Normally works within 110 ~ 125% rated output power for more than 3 seconds and switches to constant current limiting, with auto-recovery after the peak load condition is removed
				Constant current limiting, if >125% rated power, with auto-recovery after the overload condition is removed
	OVER VOLTAGE			15.5 ~ 18.2V		31 ~ 36.5V		62.1 ~ 72.9V
				Protection type : Shut down o/p voltage, re-power on to recover
	OVER TEMPERATURE			Shut down O/P voltage, recovers automatically after temperature goes down
ENVIRONMENT	WORKING TEMP.			-30 ~ +70℃ (Refer to “Derating Curve”)
	WORKING HUMIDITY			20 ~ 95% RH non-condensing
	STORAGE TEMP., HUMIDITY			-40 ~ +85℃, 10 ~ 95% RH non-condensing
	TEMP. COEFFICIENT			±0.05%/℃ (0 ~ 50℃)
	VIBRATION			10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
SAFETY & EMC(Note 9)	SAFETY STANDARDS			IEC62368-1, UL62368-1, EAC TP TC 004, J62368-1(2020)(Only for 12V) approved; Meet BS EN/EN62368-1
	WITHSTAND VOLTAGE			I/P-O/P:3KVAC	I/P-FG:2KVAC O/P-FG:0.5KVAC
	ISOLATION RESISTANCE			I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH
	EMC EMISSION			Parameter		Standard		Test Level / Note
				Conducted		BS EN/EN55032 (CISPR32) / FCC PART15 (CISPR22)		Class B
				Radiated		BS EN/EN55032 (CISPR32) / FCC PART15 (CISPR22)		Class B
				Harmonic Current		BS EN/EN61000-3-2		—–
				Voltage Flicker		BS EN/EN61000-3-3		—–
	EMC IMMUNITY			BS EN/EN55024; J55032(H29) (Only for 12V)
				Parameter		Standard		Test Level / Note
				ESD		BS EN/EN61000-4-2		Level 3, 8KV air ; Level 2, 4KV contact
				Radiated		BS EN/EN61000-4-3		Level 2, 3V/m
				EFT / Burst		BS EN/EN61000-4-4		Level 2, 1KV
				Surge		BS EN/EN61000-4-5		Level 2, 1KV/Line-Line,Level 3, 2KV/Line-Earth
				Conducted		BS EN/EN61000-4-6		Level 2, 3Vrms
				Magnetic Field		BS EN/EN61000-4-8		Level 1, 1A/m
				Voltage Dips and Interruptions		BS EN/EN61000-4-11		>95% dip 0.5 periods, 30% dip 25 periods,>95% interruptions 250 periods
OTHERS	MTBF			1199.8K hrs min.	Telcordia SR-332 (Bellcore) ; 147.5K hrs min.		MIL-HDBK-217F (25℃)
	DIMENSION			19217845.5mm (LWH)
	PACKING			1.5Kg; 10pcs/16Kg /1.38CUFT
NOTE	1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.2. Peak current or peak power up to 3 seconds is provided.3. Ripple & noise are measured at 20MHz of bandwidth by using a 12″ twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.4. Tolerance : includes set up tolerance, line regulation and load regulation.5. Line regulation is measured from low line to high line at rated load.6. Load regulation is measured from 0% to 100% rated load.7. Length of set up time is measured at cold first start. Turning ON/OFF the power supply very quickly may lead to increase of the set up time.8. Derating may be needed under low input voltages. Please check the derating curve for more details.9. The power supply is considered as an independent unit, but the final equipment still need to re-confirm that the whole system complies with the EMC directives. For guidance on how to perform these EMC tests, please refer to EMI testing of component power supplies.(as available on http://www.meanwell.com)10. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft).※ Product Liability Disclaimer：For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx

Diagram

Derating curve

Static Characteristics

Mechanical Specification

Pin No.	Assignment
1,2	+V
3,4	-V

Note: Please use wires with a cross section of 0.5 – 4.0 mm2 (12~20AWG) for connection. Recommended wires strip length is 9 mm and screw torque is 4.0 lb-inch (0.4~0.5Nm).

Installation Manual

Please refer to : http://www.meanwell.com/manual.html

Documents / Resources

MEAN WELL ENP-360 Series 360W Level Ⅵ Desktop Type Power Supply [pdf] Instruction Manual
ENP-360 Series 360W Level Desktop Type Power Supply, ENP-360 Series, 360W Level Desktop Type Power Supply, Level Desktop Type Power Supply, Desktop Type Power Supply, Desktop Type Power Supply, Type Power Supply, Power Supply, Supply

References

User Manual

Features

Description

Mechanical Specification

Documents / Resources

References

Leave a comment

Cancel reply