MEAN WELL LPV-150 Series 150W Single Output Switching Power Supply Owner's Manual

LPV-150 and LPVL-150 are 150W single-output power supplies that specifically and perfectly work for LED lighting and LED moving sign applications. As a class 11 power unit, these two series are housed with the UL 94V-O rated flame retardant plastic enclosure. The IP67 design allows every model to fit the use at dry, damp and wet locations. Both series are constant voltage mode designs that have various models with 12V, 15V, 24V, 36V, and 48V for LPV-150 where as 12V and 24V are provided for LPVL-150.

Model Encoding

Applications

Suitable for LED-related fixtures or appliances (such as LED Decoration or Advertisement devices)(Note 1 0)

GTIN CODE

MW Search: https://www.meanwell.com/serviceGTlN.aspx

SPECIFICATION

MODEL			LPV -150-12	LPV-150-15	LPV -150-24	LPV-150-36	LPV-150-48
OUTPUT	DC VOLTAGE		12V	15V	24V	36V	48V
	RATED CURRENT		10A	8A	6.3A	4.2A	3.2A
	CURRENT RANGE		0 ~ 10A	0 ~ 8A	0 ~ 6.3A	0 ~ 4.2A	0 ~ 3.2A
	RATED POWER		120W	120W	151.2W	151.2W	153.6W
	RIPPLE & NOISE (max.) Note.2		200mVp-p	200mVp-p	200mVp-p	200mVp-p	200mVp-p
	VOLTAGE TOLERANCE Note 3		±5.0%
	LINE REGULATION		±1.0%
	LOAD REGULATION		±2.0%
	SETUP, RISE TIME Note 6		LPV-150: 500ms, 50ms / 230VAC 500ms, 50ms / 277VAC; LPVL-150: 1500ms, 50ms / 115VAC
	HOLD UP TIME (Typ.)		LPV-150: 18ms/230VAC 20ms/277VAC at full load; LPVL-150: 10ms/115VAC at full load
INPUT	VOLTAGE RANGE Note 4		LPV-150: 180 ~ 305VAC 254 ~ 431VDC; LPVL-150: 90~132VAC
	FREQUENCY RANGE		47 ~ 63Hz
	EFFICIENCY (Typ.)		87%	88%	89%	89%	90%
	AC CURRENT		LPV-150: 1.7A/230VAC 1.5A/277VAC; LPVL-150: 3.0A/115VAC
	INRUSH CURRENT (Typ.)	Blank type	COLD START 60A(twidth=900μs measured at 50% Ipeak) at 230VAC
		L type	COLD START 75A(twidth=900μs measured at 50% Ipeak) at 115VAC
	MAX. No. of PSUs on 16A CIRCUIT BREAKER	Blank type	2 units (circuit breaker of type B) / 3 units (circuit breaker of type C) at 230VAC
		L type	1 unit (circuit breaker of type B) / 2 units (circuit breaker of type C) at 115VAC
	LEAKAGE CURRENT		LPV-150: 0.25mA / 240VAC LPVL-150:0.25mA / 120VAC
PROTECTION	OVERLOAD		110 ~ 150% rated output power
			Protection type: Hiccup mode, recovers automatically after the fault condition is removed
	OVER VOLTAGE		13.5 ~ 18V	17 ~ 25V	27 ~ 35V	40 ~ 49V	52 ~ 63V
			Protection type: Shut down o/p voltage, re-power on to recover
	OVER TEMPERATURE		Shut down o/p voltage, recovers automatically after the temperature goes down
ENVIRONMENT	WORKING TEMP.		-25 ~ +65℃ (Refer to “Derating Curve”)
	WORKING HUMIDITY		20 ~ 90% RH non-condensing
	STORAGE TEMP., HUMIDITY		-40 ~ +80℃, 10 ~ 95% RH
	TEMP. COEFFICIENT		±0.03%/℃ (0 ~ 40℃ for LPV-150-12,15 and LPVL-150-12,24;0~50℃ for LPV-150-24,36,48)
	VIBRATION		10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
SAFETY & EMC	SAFETY STANDARDS	Blank type	UL8750,CSA C22.2 No 250.13-12,UL879,CSA C22.2 No.207-M89,BIS IS15885(for LPV-150-12,24 only),EAC TP TC 004, IP67, IEC62368-1, BS EN/EN62368-1 approved
		L type	UL8750(type”HL”),CSA C22.2 No 250.13-12,UL879,CSA C22.2 No.207-M89,IP67 approved
	WITHSTAND VOLTAGE		I/P-O/P:3KVAC
	ISOLATION RESISTANCE		I/P-O/P:>100M Ohms / 500VDC / 25℃/ 70% RH
	EMC EMISSION	Blank type	Compliance to BS EN/EN55032 (CISPR32) Class B, BS EN/EN61000-3-2 Class A(≤80% load), BS EN/EN61000-3-3, EAC TP TC 020
		L type	Compliance to FCC part 15
	EMC IMMUNITY	Blank type	Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN55035, light industry level, EAC TP TC 020
		L type	Design refers to IEC61000-4-2,3,4,5,6,8,11; light industry level
OTHERS	MTBF		3361.2K hrs min. Telcordia SR-332 (Bellcore) ; 391.9Khrs min. MIL-HDBK-217F (25℃)
	DIMENSION		1916337.5mm (LWH)
	PACKING		LPV-150: 0.79Kg;20pcs/17Kg/0.98CUFT; LPVL-150: 0.79Kg;20pcs/17Kg/0.98CUFT

NOTE

All parameters NOT specially mentioned are measured at 230VAC(115VAC for LPVL) input, rated load, and 25℃ of ambient temperature.

Ripple & noise are measured at 20MHz of bandwidth by using a 12″ twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

Tolerance: includes setup tolerance, line regulation and load regulation.

Derating may be needed under low input voltage. Please check the static characteristics for more details.

The power supply is considered a component that will be operated in combination with the final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. (as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf)

The length of setup time is measured at first cold start. Turning ON/OFF the power supply may lead to an increase of the setup time.

Suitable for indoor use or outdoor use without direct sunlight exposure.

The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitudes higher than 2000m(6500ft).

For any application note and IP waterproof function installation caution, please refer our user manual before using.

https://www.meanwell.com/Upload/PDF/LED_EN.pdf

This product is not intended for LED lighting luminaire applications in the EU and China.(In the EU and China, the LPF/NPF/XLG/XLC/XLN series are recommended.)

※ Product Liability Disclaimer：For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx

Mechanical Specification

Recommend Mounting Direction

Block Diagram

Derating Curve
Static Characteristics

Documents / Resources

MEAN WELL LPV-150 Series 150W Single Output Switching Power Supply [pdf] Owner's Manual
LPV-150-12, LPV-150-15, LPV-150-24, LPV-150-36, LPV-150-48, LPV-150 Series 150W Single Output Switching Power Supply, LPV-150 Series, 150W Single Output Switching Power Supply, Output Switching Power Supply, Switching Power Supply, Power Supply

References

User Manual

MEAN WELL LPV-150 Series 150W Single Output Switching Power Supply

Features

Description