MT6228
Fixed Mount Scanner
Quick Guide
Out of Box
Introduction
| 1 | Good Read LED |
| 2 | Tuning Mode LED |
| 3 | No Read LED |
| 4 | Power On LED |
| 5 | Tuning Button / Scan Button |
| 6 | Mechanical Knob For Lens Focus |
I/O Box
| PIN | Signal | Function |
| 1 | Opto Isolated Input(-) | Trigger Input |
| 2 | Opto Isolated Input(+) | |
| 3 | VCC (+) | 5-36 VDC |
| 4 | GND (-) | |
| 5 | Opto Isolated Ouput (-) | Good Read Indicator |
| 6 | Opto Isolated Output (+) | |
| 7 | Opto Isolated Output (-) | No Read Indicator |
| 8 | Opto Isolated Output (+) |
Installation
Above is an installation example:
- Connect the scanner with I/O Box via aviation plug
- Connect 5~36V DC power, which is not needed when applying USB cable.
- Connect I/O Box with PC or data terminal via RS232/USB/Ethernet.
- If external trigger mode is used, an external sensor or PLC is needed.
- If OK or NG signal is needed, connect Pin 5~8 to external device.
Input Diagram
NPN Photoelectric Switch Input
PNP Photoelectric Switch Input
Relay Photoelectric Switch Input
Output Diagram
Good Read（OK）
No Read（NG）
Specifications
| Performance | |
| Resolution | 1280 x 800 |
| Scan Angle | Horizontal 28° (H), Vertical 33° (V) |
| 1D Symbologies | UPC A , UPC E , EAN 8, EAN 13 , Code 128 , Code 39, Code 93, Code 32, Code11 , Codabar, Plessey, MSI , Interleaved 2 of 5 , IATA 2 of 5 , Matrix 2 of 5 , Straight 2 of 5 , Pharmacode , RSS-14 , RSS-14 Expanded , RSS-14 Limited , Composite Code-A Composite Code-B , Composite Code-C |
| 2D Symbologies | PDF 417 , Micro PDF 417 , Data Matrix , QR , Micro QR , Aztec , MaxiCode |
| Motion Tolerance | Continuous Mode : 1M / sec External Trigger Mode : 2M / sec |
| Connectivity | |
| Interface | RS232, USB (HID; CDC), Ethernet (TCP/UDP) |
| External Input | 1 Optoisolated Input (NPN/PNP/Relay) |
| External Output | 2 Optoisolated Output (Good/NG) |
| Power | 5-36 VDC |
| Physical Characteristics | |
| Dimension | 44 (W) x 52 (D) x 29 (H) mm |
| Material | Aluminum Alloy |
| Sealing | IP65 |
| User Environment | |
| Storage Temp. | -40°C-+70°C |
| Operating Temp. | -20°C – + 50°C |
| Regulatory | TBA |
Depth of Field
| Lens Focus | LR (Long Range) | HD (High Density) |
| Resolution | 1D : ≥5 mil ; 2D :≥9 mil | 1D: ≥3 mil ; 2D: ≥7mil |
| DOF | Code39 (5 mil) : 150 mm – 300 mm EAN -13 (13 mil) : 115 mm – 550 mm QR Code (11 mil) : 125 mm – 250 mm | Code39 (3 mil) : 85 mm – 120 mm EAN-13 (13 mil) : 75 mm – 245 mm QR Code (7 mil) : 80 mm – 150 mm |
Field of View
| Distance (mm) | Field of View (mm) | |
| Horizontal (mm) | Vertical (mm) | |
| 100 | 53 | 61 |
| 150 | 79 | 91 |
| 200 | 106 | 122 |
Dimensions
Auto-tuning
- Press and hold the Tune Button for about 5 seconds.
- Aim at the desired barcode. Release the Tune Button to start Auto-tuning.
- LED status indicates Auto-tuning result (Error or Good). If the result is Good, the settings will be stored permanently. No need for re-tuning after a power cycle. If the result is Error, please start over from step 1.
Troubleshooting
If the scanner does not work properly, please do the following first:
- Check if the cable is connected firmly and is supplied by original manufacturer.
- Check if the symbology (barcode type) is enabled.
- Check if the barcode quality is good.
If the scanner still does not work properly, please contact your local distributor.
Documents / Resources
 |
Marson Technology MT6228 2D Fixed Mount Scanner [pdf] User Guide MT6228 2D Fixed Mount Scanner, MT6228 2D, Fixed Mount Scanner, Mount Scanner, Scanner |
