mars GUH92A GUH and GDD Projector Storage Bag
Specifications
- Manufacturer: Heat Controller
- Model: Single & Two Stage Gas Furnaces
- Extra Parts Bag Part Numbers: 904985, 904986, M0001118, M0001119
- Contents: Various parts for installation
Product Usage Instructions
Installation
- Refer to the furnace installation instructions for venting requirements.
- Dry-fit the components before permanent installation to ensure proper fit and alignment.
- Follow the provided table for part numbers and quantities.
Additional Notes
Ensure proper orientation of PVC components as per provided illustrations.
INSTALLATION INSTRUCTIONS
EXTRA PARTS BAG FOR SINGLE & TWO-STAGE GAS FURNACES
Parts Bag Part# 904985
| EXTRA PARTS BAG FOR GUH92A / GDD92A / GDD95A FURNACES – P/N M0001118 | ||
| PART NUMBER | DESCRIPTION | QUANTITY |
| 600364 | #10, 1-1/4” INDUCER SCREW | 1 |
| 606286 | HOSE CLAMP | 1 |
| 631758 | STRAIN RELIEF BUSHING | 1 |
| 632261 | 3 AMP FUSE | 1 |
| 663894 | CONNECTOR, UNION, 1/2” X 3/8” | 1 |
| 663989 | 1/2” BARB X 3/4” NPTF CONNECTOR | 1 |
| 664633 | INLET AIR FINISH FLANGE | 1 |
| 664886 | 14.5” DRAIN TUBE | 1 |
| 689089 | 7/8” ID GAS LINE GROMMET | 1 |
| 690074 | 2-1/4” ID VENT GROMMET | 1 |
| 690094 | 3/4” ID CONDENSATE GROMMET | 1 |
| 690101 | 3-1/2” OD FINISH FLANGE GASKET | 1 |
Table 1. Extra Parts Bag Contents – M0001118
Parts Bag Part# 904986
| EXTRA PARTS BAG FOR GUH95A & GUH95T FURNACES – P/N M0001119 | ||
| PART NUMBER | DESCRIPTION | QUANTITY |
| 600364 | #10, 1-1/4″ INDUCER SCREW | 1 |
| 606286 | HOSE CLAMP | 1 |
| 631758 | STRAIN RELIEF BUSHING | 1 |
| 632261 | 3 AMP FUSE | 1 |
| 663115 | 2″ PVC TEE | 1 |
| 663894 | CONNECTOR, UNION, 1/2” X 3/8” | 1 |
| 663989 | 1/2″ BARB X 3/4″ NPTF CONNECTOR | 1 |
| 664633 | INLET AIR FINISH FLANGE | 1 |
| 664659 | PVC TRAP | 1 |
| 664886 | 14.5” DRAIN TUBE | 1 |
| 689089 | 7/8″ ID GAS LINE GROMMET | 1 |
| 690074 | 2-1/4″ ID VENT GROMMET | 1 |
| 690094 | 3/4″ ID CONDENSATE GROMMET | 1 |
| 690101 | 3-1/2″ OD FINISH FLANGE GASKET | 1 |
Table 2. Extra Parts Bag Contents – M0001119
NOTES:
- It is necessary to vent this furnace according to the methods described in the Venting Requirement section of the furnace installation instructions.
- Please refer to the installation instructions for proper usage of the listed parts.
- Before permanently installing these components, it is recommended you dry-fit them first to ensure proper fit and alignment with other vent pipes.
709529A (Replaces 7095290)
HEAT CONTROLLER
- 1900 Wellworth Ave., Jackson MI 49203
- Ph. 517-787-2100
- www.heatcontroller.com
- Specifications & illustrations subject to change without notice or incurring obligations (1 0/13).
FAQs
Q: Can these parts be used for other furnace models?
A: It is recommended to use these parts specifically for the mentioned furnace models to ensure compatibility and proper installation.
Q: Are additional tools required for installation?
A: Additional tools such as PVC pipe, tubing, and fittings may be required as specified in the installation instructions.
Documents / Resources
 |
mars GUH92A GUH and GDD Projector Storage Bag [pdf] Installation Guide GUH92A, GUH92A GUH and GDD Projector Storage Bag, GUH and GDD Projector Storage Bag, Projector Storage Bag, Storage Bag |