MARS GAMING MFSI4KIT Computer Cooling System
CONTROL HUB CONNECTIONS
Specifications
- 120x120x25mm / 165g
- DC12V – 0.4A
Fan Installation
- Choose the location in the case where you want to install the fan and orient the front part with the logo facing outside the case for air intake or facing inside if your goal is to extract hot air.
- Screw the fans to the case using the included screws.
Control HUB
- Fan: Connect the 4-pin cable from the fan to the “FAN” 4-pin port on the HUB.
Note: The HUB is designed exclusively for use with the fans included with the case. It is not recommended to connect other fans to the HUB as this may compromise the function of the fan and damage the HUB. - Power: Connect the SATA connector from the power supply to the SATA port on the HUB.
- Connect Button (Optional): Allows you to control the lighting effects via the button on the case in addition to the remote control. Connect the “RESET SW” cable to the 2-pin connector on the HUB.
- Connect M/B (Optional): Allows you to change lighting effects via the control software of an ARGB-compatible motherboard or other ARGB controller.
REMOTE CONTROL
- Power On/Off
- Minimum/maximum fan speed
- Speed adjustment
- Change the lighting effect
- Adjust the lighting brightness
- Fixed colors
- Automatic lighting change
- Select PRESET/ARGB lighting mode
Lighting
- PRESET lighting modes: The HUB includes multiple preset lighting effects that can be controlled via the remote control.
- ARGB Lighting Mode (Optional): Fan lighting can be controlled by a compatible ARGB motherboard or controller, using the ARGB cable.
- Connect the ARGB cable to the 3-pin +5V connector on the motherboard or controller.
- Press the M/B button on the control knob, the HUB will enter ARGB lighting mode. Press the M/B button again if you want to return to PRESET lighting mode.
Note: Please make sure your motherboard or controller supports 3-pin +5V ARGB lighting. Make sure the ARGB connector on the fans is connected to the correct ARGB control device port; otherwise, components may be damaged. If you have any doubts about your motherboard or controller’s compatibility with ARGB lighting, please feel free to contact us for help.
Recommendations and Safety Reminders
- Keep children away from the equipment parts while installing the product.
- Protect your hands and fingers when handling and installing the product.
- Disconnect the computer from the power supply before installation.
- Turn off and unplug the computer before cleaning the fan.
- Use compressed air to remove accumulated dust on the blades and frame.
- Avoid direct contact with the fan blades while in operation.
- Keep the computer in a clean, dry environment away from heat, dust, and moisture, as these can shorten the lifespan of the fans.
- DO NOT open the product casing; the unit operates at dangerous voltages.
- DO NOT modify the cables or connectors included with this product.
- DO NOT use cable adapters or cables not included.
- DO NOT apply excessive force when plugging and unplugging connectors.
Important Notice: If you notice any defects or irregularities in the product, please do not proceed with the installation and contact our customer service immediately. Failure to follow these guidelines could result in injury or additional damage.
Troubleshooting
- Fan not spinning: Check the connections and ensure they are correctly installed.
- Excessive noise: Ensure there is no object obstructing the fan. The fan may generate noise if running at a very high speed; adjust the fan speed using the remote to reduce the speed without compromising cooling. If the fan has been exposed to dust or dirt, it may have deteriorated-contact us for assistance.
- Fans not lighting up: Ensure the fans are connected as shown in the connection diagram.
- ARGB lighting mode not working: Ensure the ARGB connector is plugged into the motherboard or ARGB controller, and that the HUB is in ARGB lighting mode. Verify the motherboard’s ARGB compatibility.
- The remote control does not work: The signal from the remote may be weak if there are many obstacles between the remote and the HUB. Move the remote control closer to the HUB and point it in the direction of the HUB, press the buttons. Check that the battery of the remote control has battery power.
Warranty
- The original purchase receipt will be required to use the warranty service.
- Please keep it in a safe place. Opening the device, tampering with it, making technical modifications of any kind, or damage caused by external mechanical forces will void your warranty.
- For the terms and conditions of the warranty, visit es.marsgaming.eu/es/terms.
CONTACT
- MARSGAMING
- Biomag S. L.
- EU office:
- Address: Barratxi 39, Pab. 3
- 01013, Vitoria, SPAIN
- Telephone: +34945124598
- Email: attcliente@biomag.es
- Made In China
Documents / Resources
 |
MARS GAMING MFSI4KIT Computer Cooling System [pdf] User Manual MFSI4KIT, MF-SI4KIT-MANUAL, MFSI4KIT Computer Cooling System, MFSI4KIT, Computer Cooling System, Cooling System, System |