D10 Smart Mini Label Maker
Specifications
- Product name: Smart Mini Label Maker D10
- Product model: D10
- Printing technology: Thermal printing
- Consumable width: 12-15mm
- Effective printing width: 12mm
- Supported consumables: Pre-cut paper, black mark paper,
continuous paper - Printing density: Light, standard, dark
- Printing resolution: 203 dpi
- Print head service life: 50
- Communication interface: Bluetooth
- Product size: 133.5*80.5*33.5mm (5.2*3.2*1.3inch)
- Power input: 5V 2A
- Power supply method: Lithium Battery
- Supported operating system: Android/iOS
Product Usage Instructions
1. Parts Description
3.1 Appearance Introduction
Describe the physical appearance of the label maker.
Explain the functions of the power button and indicator light as
per the manual.
2. Power On/Off and Calibration
Guide on how to power on/off the device and calibrate the label
position.
3. Printing Instructions
Explain how to print a self-test page and adjust printing
settings.
4. Guidelines for Use
- Open the paper compartment cover of the machine.
- Take out the label paper and remove the anti-loosening
sticker.
5. Downloading the App
Provide instructions on downloading the app using the QR code or
alternative methods for different devices.
6. Printer Connection
- Select your printer from the app.
- Tap on [ Tap to connect ] for connection.
- Wait for the printer to be connected.
FAQ
How do I know if the printer is fully charged?
If the indicator light shows a solid green light, the device is
functioning properly and fully charged.
What should I do if the printer shows a fast flashing red
light?
If the red light is flashing fast, it indicates that the battery
is running low. You should charge the printer for 2-3 hours to
ensure proper functionality.
Quick Start Guide
D10
Smart Mini Label Maker HVIN:D10
English
1. Packing List
Printer ×1
Quick Start Guide
EN DE FR
Product instruction ×1
1Charging line ×1
The number of paper rolls in the list is subject to the actual shipment.
2. Product Specifications
Product name Product model Printing technology Consumable width Effective printing width
Smart Mini Label Maker D10 Thermal printing 12-15 12
Supported consumables Pre-cut paperblack mark paper continuous paper
Printing density
Lightstandarddark
Printing resolution
203 dpi
Print head service life
50
Communication interface Bluetooth
Product size
133.5*80.5*33.5mm (5.2*3.2*1.3inch)
Power input
5V 2A
Power supply method
Lithium Battery
Supported operating system
Android/iOS
3. Parts Description 3.1 Appearance Introduction
3.2 Power Button and Indicator Light
6. Downloading the App
10. Information to User
Button Instructions
2Indicator light
Button Type Power Button
Operation Long press for 3s Press once when printer is on Double press when printer is on
Function Power on/off Calibrate label position Print a self-test page
Indicator Light Instructions
Status
Meaning
Advised Action
Solid Green Light
Device functioning properly and fully charged
/
Fast Flashing Green Light
Charging when printer is off /
Slow Flashing Green Light
Charging when printer is on /
Solid Red Light
Out of paper Printer overheat
Properly insert label paper into Paper Outlet
Pause printing for 5 min for printer to cool down
Slow Flashing Red Light
Low battery
Charge for 1 hour (or at least 20 min if in urgent need)
Fast Flashing Red Light
Battery running low
Charge for 2-3 hours
4. Guidelines for Use
01 Open the paper compartment cover of the machine.
02 Take out the label paper, tear off the anti-loosening sticker.
Method 1: Search for the “Print Master” app on App Store® or Google PlayTM for download and installation.
Print Master Method 2: Scan the QR code to download the app.
3Print Master
As the Safari browser on Apple devices does not support direct QR code scanning, please use your device’s built-in QR code scanner instead.
7. Printer Connection
01 Select your printer.
02 Tap [ Tap to connect ] at the top left corner for connection.
Choose your printer D30S/D10
Tap to connect
03 Wait for the printer to be connected. 04 The printer is successfully connected.
Searching for printer…
Connected
· This product needs to be connected to the printer in the App after the Bluetooth is turned
on. · According to the official requirements of Google, Android mobile phones need to open the
GPS permission before they can use the Bluetooth function. · When connecting the App, please make sure that the printer is turned on and the Bluetooth
of the mobile phone is turned on.
4 10.1 FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC RF exposure statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
10.2 ISED NOTICE(Canada)
IC Warning This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1) L’appareil ne doit pas produire de brouillage; 2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
IC RF Exposure Statement/ IC Déclaration d’exposition aux RF: The device has been evaluated to meet general IC RF exposure requirement. The device can be used in portable exposure condition without restriction. L’appareil a été évalué pour répondre aux exigences générales d’exposition aux RF d’IC. L’appareil peut être utilisé dans des conditions d’exposition portable sans restriction.
03 Depending on the direction of the marking, place the label paper into the paper compartment.
04 Pull out the label paper out of the Paper exit by 5 in length for normal printing.
Pull out 5
05 Long press the ON/OFF button to connect with an APP.
8. Confirm the Label Size
Method 1: Check the label paper packaging.Please refer to the actual size used.
Method 2: Check the label paper pads. The old and new versions of label paper are being replaced, please refer to the actual shipment.
Product : Pattern label
Model Detail
: :
DP – P06 Polar bear,
Spec : 12*40mm /
Seal, Snow 210 pcs
fox
Quantity : 3
1
Please do not tear 2mm*40mm 3/8″*1 1
/2″
9. Detailed Online Guide
Method 1: Visit https://ms.printsupport.cn/?mo=D10 to access the Detailed Online Guide, video tutorials, and answers to FAQs.
10.3 BATTERIES
1, Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
2, Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas
3, The battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
4, Replacement of a battery with an incorrect type that can result in an explosion or the leakage of flammable liquid or gas.
5, Battery cannot be subjected to extremely high or low temperatures, low air pressure at high altitude during use, storage or transportation.
Battery Capacity : 3.7V 1200mAh 4.44Wh Type: Li-ion Polymer Battery
https://ms.printsupport.cn/?mo=D10
Method 2: Scan the QR code to access the Detailed Online Guide, video tutorials, and answers to FAQs.
5. Boot Guide
01 Press the Power Button once when the printer is on to identify the label position.
02 the Paper Outlet will automatically release a blank piece oflabel paper, indicating calibration is complete.
As the Safari browser on Apple devices does not support direct QR code scanning, please use your device’s built-in QR code scanner instead.
Label paper display Various labels available for purchase
Pre-cut paper display Continuous paper display
· When installing or replacing the label roll for the first time, the label position
identification is required.Step 01 · If the label position identification is not carried out Step 01 , failures may occur such as
first printing missing, not centered, etc.
Special Notes
The company assumes full responsibility for the revision and explanation of this manual, exercising utmost diligence to guarantee its accuracy. Nevertheless, please note that any technical improvements to the product may not be separately notified, and that the images of the product, accessories, software interfaces, etc. in this manual serve solely as illustrations and references. Due to product updates and upgrades, the actual product may vary slightly from the images. Please refer to the physical product for accurate representations.
5
Documents / Resources
 |
Mandizza D10 Smart Mini Label Maker [pdf] User Guide 2ASRB-D10, 2ASRBD10, D10 Smart Mini Label Maker, D10, Smart Mini Label Maker, Mini Label Maker, Label Maker, Maker |