Indoor Installation:
– Locate a suitable indoor location for mounting the PIR44.
– Ensure the power supply matches the specified voltage
range.
– Adjust the detection area and distance as needed.
– Mount the PIR44 securely following the provided
instructions.

Outdoor Installation:
– Choose an outdoor location with adequate protection from
elements.
– Connect the PIR44 to the power supply within the voltage
range.
– Adjust motion speed and time delay settings for optimal
performance.
– Mount the device securely, ensuring it has a clear detection
area.
Setting Adjustments:
– Use provided controls to adjust detection range, time delay, and
ambient light sensitivity.
– Test the PIR44 after adjustments to ensure proper
functionality.

Maintenance:
– Regularly clean the sensor area to prevent dust
accumulation.
– Check connections periodically for any signs of wear or
damage.

Frequently Asked Questions (FAQ)

Q: Can the detection area be customized?

A: Yes, the detection area of the PIR44 can be adjusted to suit
specific needs.

Q: Is the PIR44 suitable for use in all weather
conditions?

A: The PIR44 is designed for both indoor and outdoor use, but
proper protection in extreme weather conditions is recommended.

Q: How do I reset the settings on the PIR44?

A: Refer to the user manual for instructions on resetting the
PIR44 settings to default.

View Fullscreen

INSTRUCTION MANUAL
PIR44
180° PIR Motion Sensor
Indoor & Outdoor Installation

1. INTRODUCTION The PIR44 automa cally turns on lights or any electrical device within the sensors rated load, when mo on and body heat is detected. It has a 180° detec on range and adjustable se ngs, easily integra ng into new or exis ng installa ons. With an IP65 ra ng, it can be installed indoors or outdoors. Installa on must be done by a qualified electrician.

2. SPECIFICATIONS
Function Voltage Power Frequency Ambient Light Time Delay Rated Load Detection Area Detection Distance Detection Motion Speed Mounting

Range 220 – 240V AC 50/60 Hz <3 – 2000 Lux (Adjustable) 10 sec (±3 sec) to 15 min (±2 min) 1200W Incandescent/ 600W LED/CFL 180° 12m Max 0.6 – 1.5m/s Wall and Ceiling Mountable

Function Working Temperature Working Humidity Power Consumption Installation Height IP Protection Swivel Head Warranty Standards

Range -20~40°C <93% RH Approx. 0.5W 1.8 – 2.5m IP65 Indoor & Outdoor 45° (L to R), 180° (Up/Down) 5 years IEC 60669-1, IEC 60669-2-1 AS/NZS 60669.1, AS/NZS 60669.2.1

3. FUNCTION a. Sensor Can identify between day and night (Lux Mode):
The consumer can adjust working state in different ambient light. It can work in the day time and at night when it is adjusted on the ” ” (sun) position (max). It can work in the ambient light less than 3 LUX when it is adjusted on the “3” position (min). As for the adjustment pattern, please refer to the testing pattern. b. Time-Delay is added continually: When the sensor detects movement while the light is already on, the countdown timer resets. This means the light will remain On for the full set duration from the moment of the latest detection. c. Adjustable Time Delay: The sensor can be set according to the consumer’s desire (10s, 30s, 90s, 3min, 7min, 15min)
4. CONTROL SETTING INFORMATION ! Turn the TIME knob anticlockwise to the minimum (10s). Turn the LUX knob clockwise to the maximum (Sun). ! Switch on the power; the sensor will require 30 seconds to warm up. Once the sensor detects movement, the lamp will turn On. If
no other movement is detected within the time duration set, the light will turn Off within the 10 seconds ±3 sec. ! Turn the LUX knob anticlockwise to the minimum (3). If the ambient light is more than 3 Lux, the sensor is not able to function. If the
ambient light is less than 3 Lux (dark), the sensor will operate.
Note: When testing in daylight, please turn Lux knob to (Sun) position, otherwise the sensor will not work!

5. WIRING INFORMATION

WARNING: Danger of Death Through Electrical Shock Y Must be installed by professional
electrician. Y Disconnect power source. Y Cover or shied any adjacent live
components.

6. INSTALLATION

! Unscrew and remove fixing bracket from base of the sensor. ! Insert the power cable into the slot provided. ! Connect the power cable into the terminal block as per the wiring
diagram. ! Identify the ideal field of view and use fixing bracket mounting
holes to ensure correct alignment for motion sensor. ! Drill holes and screw the fixing bracket to the marked location. ! Reconnect the sensor to the fixing bracket and fasten the screws. ! Once installation is complete, swivel the head to point in the
intended direction, secure it, and turn on the power to test.

7. INSTALLATION ADVICE ! Avoid pointing the detector towards objects with
highly reflective surfaces, such as mirrors etc. ! Avoid mounting the detector near heat sources, such
as heating vents, air conditioning units, light etc. ! Avoid pointing the detector towards objects that may
move in the wind, such as curtains, tall plants etc.
8. SENSOR INFORMATION

Note: The PIR sensor operates by detecting motion when the detector beams are interrupted, typically by the movement of an object or a walking person. If a person walks directly in front of or towards the beam, the sensor may not detect movement. However, when two beams are crossed, the PIR sensor detects movement, as it picks up the change in the infrared radiation pattern caused by the interruption of both beams. This method increases detection accuracy and reduces the chances of false or non-detection.

8. TROUBLESHOOTING

MAJOR TECH (PTY) LTD

South Africa

Australia

www.major-tech.com

www.majortech.com.au

sales@major-tech.com

info@majortech.com.au

Documents / Resources

Major Tech PIR44 180° PIR Motion Sensor [pdf] Instruction Manual
PIR44, PIR44 180 PIR Motion Sensor, PIR44 180, PIR Motion Sensor, Motion Sensor, Sensor

References

User Manual

Major Tech PIR44 180° PIR Motion Sensor Instruction Manual

PIR44 180° PIR Motion Sensor

Product Information

Specifications

Product Usage Instructions