PIR36 360° PIR Motion Sensor
Product Information
Specifications
- Function: PIR36
- Voltage: 220 – 240V AC
- Power Frequency: 50/60 Hz
- Ambient Light: Included
- Time Delay: Adjustable
- Rated Load: Not specified
- Detection Area: Variable
- Detection Distance: Variable
- Detection Motion Speed: Variable
- Installation Type: Indoor
Product Usage Instructions
- Installation:
- Adjustment:
- Operation:
1. Ensure the power supply is switched off before
installation.
2. Mount the PIR36 device securely in the desired indoor
location.
3. Connect the device to a 220-240V AC power source.
1. Adjust the time delay according to your preference using the
provided controls.
2. Set the detection area and distance based on your
requirements.
1. Once installed and adjusted, the PIR36 will detect motion
within the set parameters.
2. The device will trigger a response based on the settings and
connected load.
Frequently Asked Questions (FAQ)
Q: What is the maximum load the PIR36 can handle?
A: The maximum load capacity of the PIR36 is not specified in
the manual. Please refer to the product specifications for more
details.
Q: Can the detection range be adjusted?
A: Yes, the detection area and distance of the PIR36 can be
adjusted to suit your needs.
INSTRUCTION MANUAL
PIR36
360° PIR Motion Sensor
Indoor Installation
1. INTRODUCTION The PIR36 automa cally turns on lights or any electrical device within the sensors rated load, when mo on and body heat is detected. It has a 360° detec on range and adjustable se ngs, easily integrated into new or exis ng installa ons. With an IP20 ra ng, the sensor is intended for indoor installa ons. Installa on must be done by a qualified electrician.
2. SPECIFICATIONS
Function Voltage Power Frequency Ambient Light Time Delay Rated Load Detection Area Detection Distance Detection Motion Speed Installation Type
Range 220 – 240V AC 50/60 Hz <3 – 2000 Lux (Adjustable) 10 sec (±3 sec) to 15 min (±2 min) 2000W Incandescent/ 1000W LED/CFL 360° 8m Max <24°C 0.6 to 1.5m/s Ceiling Surface Mount
Function Working Temperature Working Humidity Power Consumption Installation Height IP Protection Swivel Head Warranty Standards
Range -20~40°C <93% RH Approx. 0.5W 2.2 – 4m IP20 Indoor Installation No 5 years IEC 60669-1, IEC 60669-2-1 AS/NZS 60669.1, AS/NZS 60669.2.1
3. FUNCTION a. Sensor Can identify between day and night (Lux Mode):
The consumer can adjust working state in different ambient light. It can work in the day time and at night when it is adjusted on the ” ” (sun) position (max). It can work in the ambient light less than 3 LUX when it is adjusted on the “3” position (min). As for the adjustment pattern, please refer to the testing pattern. b. Time-Delay is added continually: When the sensor detects movement while the light is already on, the countdown timer resets. This means the light will remain On for the full set duration from the moment of the latest detection. c. Adjustable Time Delay: The sensor can be set according to the consumer’s desire (10s, 30s, 90s, 3min, 7min, 15min)
4. CONTROL SETTING INFORMATION ! Turn the TIME knob anticlockwise to the minimum (10s). Turn the LUX knob clockwise to the maximum (Sun). ! Switch on the power; the sensor will require 30 seconds to warm up. Once the sensor detects movement, the lamp will turn On. If
no other movement is detected within the time duration set, the light will turn Off within the 10 seconds ±3 sec. ! Turn the LUX knob anticlockwise to the minimum (3). If the ambient light is more than 3 Lux, the sensor is not able to function. If the
ambient light is less than 3 Lux (dark), the sensor will operate.
Note: When testing in daylight, please turn Lux knob to (Sun) position, otherwise the sensor will not work!
5. SENSOR INFORMATION
6. INSTALLATION & WIRING OPTIONS
! Unscrew and remove fixing bracket from base of the sensor. ! Insert the power cable into the slot provided. ! Connect the power cable into the terminal block as per the wiring diagram. ! Identify the ideal field of view and use fixing bracket mounting holes to ensure
correct alignment for motion sensor. ! Drill holes and screw the fixing bracket to the marked location. ! Reconnect the sensor to the fixing bracket and fasten the screws. ! Once installation is complete, swivel the head to point in the intended
direction, secure it, and turn on the power to test.
Single Sensor Installation
L N N L1
Multiple Sensor Installation
WARNING: Danger of Death Through Electrical Shock Y Must be installed by professional electrician. Y Disconnect power source. Y Cover or shied any adjacent live components. Y Ensure device cannot be switched on. Y Check power supply is disconnected.
L N N L1
L N N L1
L N N L1
7. INSTALLATION ADVICE ! Avoid pointing the detector towards objects with highly
reflective surfaces, such as mirrors etc. ! Avoid mounting the detector near heat sources, such as
heating vents, air conditioning units, light etc. ! Avoid pointing the detector towards objects that may move in
the wind, such as curtains, tall plants etc.
Note: The PIR sensor operates by detecting motion when the detector beams are interrupted, typically by the movement of an object or a walking person. If a person walks directly in front of or towards the beam, the sensor may not detect movement. However, when two beams are crossed, the PIR sensor detects movement, as it picks up the change in the infrared radiation pattern caused by the interruption of both beams. This method increases detection accuracy and reduces the chances of false or non-detection.
8. TROUBLESHOOTING
MAJOR TECH (PTY) LTD
South Africa
Australia
www.major-tech.com
www.majortech.com.au
sales@major-tech.com
info@majortech.com.au
Documents / Resources
 |
MAJOR TECH PIR36 360° PIR Motion Sensor [pdf] Instruction Manual PIR36 360 PIR Motion Sensor, PIR36, 360 PIR Motion Sensor, PIR Motion Sensor, Motion Sensor, Sensor |