PIR32 360° Ceiling Mount PIR Sensor
Product Information
Specifications
- Function: PIR32
- Voltage: 220 – 240V AC
- Power Frequency: 50/60 Hz
- Ambient Light: Yes
- Time Delay: Adjustable
- Rated Load: Depends on model
- Detection Area: Wide coverage
- Installation Height: Recommended height from the floor
- Detection Distance: Varies based on installation and model
- Detection Motion Speed Range: Adjustable
Product Usage Instructions
Indoor Installation
- Choose a suitable location for mounting the PIR32 unit
indoors. - Ensure the power supply meets the specified voltage
requirements of 220 – 240V AC. - Mount the unit securely at the recommended installation height
from the floor for optimal performance. - Adjust the detection area and motion speed range as needed
based on your requirements. - Refer to the user manual for specific programming instructions
and troubleshooting tips.
Frequently Asked Questions (FAQ)
Q: How do I adjust the time delay on the PIR32 unit?
A: To adjust the time delay, refer to the user manual for
detailed instructions on accessing the settings and making
changes.
Q: What is the recommended detection distance for the PIR32
unit?
A: The recommended detection distance can vary based on the
specific model and installation height. Refer to the product
specifications or consult with customer support for guidance.
INSTRUCTION MANUAL
PIR32
360° Ceiling Mount PIR Sensor
Indoor Installation
1. INTRODUCTION The PIR32 automa cally turns on lights or any electrical device within the sensors rated load, when mo on and body heat is detected. It has a 360° detec on range and adjustable se ngs for me and Lux level, easily integrated into new or exis ng installa ons. With an IP20 ra ng, the sensor is intended for indoor installa ons. Installa on must be done by a qualified electrician.
2. SPECIFICATIONS
Function Voltage Power Frequency Ambient Light Time Delay Rated Load Detection Area Installation Height Detection Distance Detection Motion Speed
Range 220 – 240V AC 50/60 Hz <3 – 2000 Lux (Adjustable) 10 sec (±3 sec) to 15 min (±2 min) 1200W Incandescent/ 600W LED/CFL 360° 2.2m to 4m 6m 0.6 to 1.5m/s
Function Working Temperature Working Humidity Power Consumption Mounting Hole Cut Out Size IP Protection Swivel Head Warranty Standards
Range -20~40°C <93% RH <0.5W Ceiling Mount Ø64mm IP20 Indoor Installation No 5 years IEC 60669-1, IEC 60669-2-1 AS/NZS 60669.1, AS/NZS 60669.2.1
3. FUNCTION a. Sensor Can identify between day and night (Lux Mode):
The consumer can adjust working state in different ambient light. It can work in the day time and at night when it is adjusted on the ” ” (sun) position (max). It can work in the ambient light less than 3 LUX when it is adjusted on the “3” position (min). As for the adjustment pattern, please refer to the testing pattern. c. Time-Delay is added continually: When the sensor detects movement while the light is already on, the countdown timer resets. This means the light will remain On for the full set duration from the moment of the latest detection. d. Adjustable Time Delay: The sensor can be set according to the consumer’s desire (10s, 3s, 90s, 5min, 10min, 30min)
4. Manual Override: AUTO MODE will automatically occur when power is initially applied to the PIR37 1. MANUAL MODE
Switch power OFF-ON, OFF-ON twice within 3 seconds, the PIR sensor will remain on continuously. 2. AUTO MODE
* Switch your power OFF, then switch ON after 3 seconds, Auto Mode initiated
* Leave the power ON if in Manual Mode, then PIR sensor will automatically revert to Sensor Mode after 8 hours
Note: When testing in daylight, please turn Lux knob to (Sun) position, otherwise the sensor will not work!
5. SENSOR INFORMATION
Note: The PIR sensor operates by detecting motion when the detector beams are interrupted, typically by the movement of an object or a walking person. If a person walks directly in front of or towards the beam, the sensor may not detect movement. However, when two beams are crossed, the PIR sensor detects movement, as it picks up the change in the infrared radiation pattern caused by the interruption of both beams. This method increases detection accuracy and reduces the chances of false or non-detection.
6. INSTALLATION & WIRING OPTIONS
Y Unscrew and remove fixing bracket from base of the sensor. Y Insert the power cable into the slot provided. Y Connect the power cable into the terminal block as per the wiring diagram. Y Identify the ideal field of view and use fixing bracket mounting holes to
ensure correct alignment for motion sensor. Y Drill holes and screw the fixing bracket to the marked location. Y Reconnect the sensor to the fixing bracket and fasten the screws. Y Once installation is complete, swivel the head to point in the intended
direction, secure it, and turn on the power to test.
WARNING: Danger of Death Through Electrical Shock Y Must be installed by professional electrician. Y Disconnect power source. Y Cover or shied any adjacent live components. Y Ensure device cannot be switched on. Y Check power supply is disconnected.
Multiple Sensor Installation
Single Sensor Installation
7. INSTALLATION ADVICE ! Avoid pointing the detector towards objects with highly
reflective surfaces, such as mirrors etc. ! Avoid mounting the detector near heat sources, such as
heating vents, air conditioning units, light etc. ! Avoid pointing the detector towards objects that may move
in the wind, such as curtains, tall plants etc.
Note: The PIR sensor operates by detecting motion when the detector beams are interrupted, typically by the movement of an object or a walking person. If a person walks directly in front of or towards the beam, the sensor may not detect movement. However, when two beams are crossed, the PIR sensor detects movement, as it picks up the change in the infrared radiation pattern caused by the interruption of both beams. This method increases detection accuracy and reduces the chances of false or non-detection.
8. TROUBLESHOOTING
MAJOR TECH (PTY) LTD
South Africa
Australia
www.major-tech.com
www.majortech.com.au
sales@major-tech.com
info@majortech.com.au
Documents / Resources
 |
Major Tech PIR32 360° Ceiling Mount PIR Sensor [pdf] Instruction Manual PIR32, PIR32 360 Ceiling Mount PIR Sensor, PIR32, 360 Ceiling Mount PIR Sensor, Ceiling Mount PIR Sensor, PIR Sensor, Sensor |