Power Supply: Ensure the product is connected
to a 220 – 240V AC power source with a frequency of 50/60 Hz.
Adjustments: Configure the detection area,
time delay, and other settings as needed for optimal
performance.

Mounting: Mount the MS360 device securely
within the recommended mounting range for effective motion
detection.
Maintenance: Regularly clean the device to
prevent dust or debris from affecting its functionality.

Frequently Asked Questions (FAQ)

Q: What should I do if the MS360 does not detect motion?

A: Check the power supply, ensure the detection area is clear of
obstructions, and adjust the settings to enhance sensitivity if
needed.

Q: Can the MS360 be used outdoors?

A: No, the MS360 is designed for indoor installation only.

Q: How can I reset the MS360 to its default settings?

A: Refer to the user manual for instructions on resetting the
device to factory settings.

View Fullscreen

INSTRUCTION MANUAL
MS360
360° Microwave Sensor
Indoor Installation

1. INTRODUCTION The MS360 automatically turns on lights or any electrical device within the sensors rated load. With a detection range adjustable from 2m to 16m this sensor can detect movement through obstacles like doors, glass panels, and thin walls, this 360° sensor includes adjustable settings for time, Lux level and sensitivity. The MS360 can simply be installed on ceilings and easily integrated into new or existing installations, it excels in detecting subtle movements over large areas compared to PIR sensors. Its IP20 rating is suitable for indoor installation. Installation must be done by a qualified electrician.

2. SPECIFICATIONS
Function Voltage Power Frequency Ambient Light Time Delay Rated Load Detection Area HF System Detection Distance Detection Motion Speed Mounting

Range 220 – 240V AC 50/60 Hz <3 – 2000 Lux 10 sec (±3 sec) to 12 min (±2 min) 2000W Incandescent/ 1000W LED/CFL 360° 5.8GHz CW Radar, ISM Band Min 2m to 16m 0.6 to 1.5m/s Ceiling Mount

Function Working Temperature Working Humidity Power Consumption Installation Height IP Protection Swivel Head Warranty Standards

Range -20~40°C <93% RH <0.9W 2 – 6m IP20 Indoor Installation No 5 years IEC 60669-1, IEC 60669-2-1 AS/NZS 60669.1, AS/NZS 60669.2.1

3. FUNCTION a. Sensor Can identify between day and night (Lux Mode):
The consumer can adjust working state in different ambient light. It can work in the day time and at night when it is adjusted on the ” ” (sun) position (max). It can work in the ambient light less than 3 LUX when it is adjusted on the “3” position (min). As for the adjustment pattern, please refer to the testing pattern. b. Adjustable SENS (Sensitivity Mode): Can be adjusted according to location. The detection distance of wall mounting (2 – 16 metres). c. Time-Delay is added continually: When the sensor detects movement while the light is already on, the countdown timer resets. This means the light will remain On for the full. d. Adjustable Time Delay: The sensor can be set according to the consumer’s desire, (10s, 30s, 90s, 3min, 6min, 12min) set duration from the moment of the latest detection.

4. CONTROL SETTING INFORMATION Y Turn the TIME knob anticlockwise to the minimum (10s). Turn the LUX knob clockwise to the maximum (Sun). Y Switch on the power; the sensor will require 30 seconds to warm up. Once the sensor detects movement, the lamp will turn On. If no
other movement is detected within the time duration set, the light will turn Off within the 10 seconds ±3 sec. Y Turn the LUX knob anticlockwise to the minimum (3). If the ambient light is more than 3 Lux, the sensor is not able to function. If the
ambient light is less than 3 Lux (dark), the sensor will operate.

Note: When testing in daylight, please turn Lux knob to (Sun) position, otherwise the sensor will not work!

5. INSTALLATION & WIRING OPTIONS

Y Unscrew and remove fixing bracket from base of the sensor. Y Insert the power cable into the slot provided. Y Connect the power cable into the terminal block as per the wiring
diagram. Y Identify the ideal field of view and use fixing bracket mounting holes to
ensure correct alignment for motion sensor. Y Drill holes and screw the fixing bracket to the marked location. Y Reconnect the sensor to the fixing bracket and fasten the screws. Y Once installation is complete, swivel the head to point in the intended
direction, secure it, and turn on the power to test.

WARNING: Danger of Death Through Electrical Shock Y Must be installed by professional electrician. Y Disconnect power source. Y Cover or shied any adjacent live components. Y Ensure device cannot be switched on. Y Check power supply is disconnected.
Multiple Sensor Installation

Single Sensor Installation L N N L1

L N N L1 6. MICROWAVE SENSOR INFORMATION

L N N L1

7. TROUBLESHOOTING

MAJOR TECH (PTY) LTD

South Africa

Australia

www.major-tech.com

www.majortech.com.au

sales@major-tech.com

info@majortech.com.au

Documents / Resources

MAJOR TECH MS360 360° Microwave Sensor [pdf] Instruction Manual
MS360 360 Microwave Sensor, MS360, 360 Microwave Sensor, Microwave Sensor, Sensor

References

User Manual

MAJOR TECH MS360 360° Microwave Sensor Instruction Manual

MS360 360° Microwave Sensor

Product Information

Specifications

Product Usage Instructions