MAGUS CHD30 Digital Camera User Manual

MAGUS-logo

MAGUS CHD30 Digital Camera

MAGUS-CHD30-Digital-Camera-productProduct Overview

MAGUS-CHD30-Digital-Camera-fig- (1)

  1. HDMI port
  2. Wi-Fi antenna/USB
  3. connector
  4. DC port
  5. ON/OFF button
  6. SD card slot

MAGUS CHD30 DIGITAL CAMERA

Never look at the sun, a bright light source, or a laser beam through the camera. It can cause permanent damage to your eyes. MAGUS high-speed HDMI cameras are designed to be paired with a digital microscope. Sony Starvis’s high-sensitivity sensor ensures perfect color reproduction and image quality even in low-light conditions. You can install the camera software to view, save, and edit captured images and videos.

The rugged aluminum housing is designed for operation at low temperatures (–10°C). Before starting the camera please connect the standard C-mount camera to the camera adapter and connect it to the third tube of the microscope which will convey the middle image of the object to the camera sensor.

CONNECT THE CAMERA TO A PC/LAPTOP VIA WI-FI
Make sure your PC supports Wi-Fi.

  1. Install the MAGUSView software from the USB flash drive (included in the kit) on the PC.
  2. Connect the camera to the power supply (3). Turn the camera on (4).
  3. Connect the Wi-Fi antenna to the connector (2).
  4. After the antenna starts blinking, select the Wi-Fi network that you want to connect to on your PC. The password is 12345678.
  5. Open the MAGUS View program. Choose a camera from the list.

HDMI

  1. Use an HDMI cable to connect the camera to an HDMI monitor (1).
  2. Connect the USB mouse to the connector (2).
  3. Insert the memory card into the memory card slot (5).
  4. Connect the camera to the power supply (3). Turn the camera on (4).
  5. Turn the monitor on and view the video in the built-in program.

CALIBRATION USING A CALIBRATION SLIDE
You should use a special stage micrometer (calibration slide) to determine the linear dimensions (in millimeters or microns). The calibration slide is a transparent glass (of the same size as the specimen slide) that has a micrometer scale with a scale division of 0.01mm etched on the surface. The calibration slide (stage micrometer) is used to calibrate the image analysis software for measurements in actual units. In the calibration mode, you should capture an image of the micrometer scale with every objective magnification and indicate the known distance. That lets you establish a scale of the image in actual units (micrometer, millimeter, etc.).

MAGUS-CHD30-Digital-Camera-fig- (2)

Calibration

  1. Place the calibration slide on the microscope stage.
  2. Select the required objective and set the maximum camera resolution.
  3. Get a contrast image of the scale on the monitor screen and capture the image.
  4. Select the ”Calibrate” function in the software you are using.
  5. Double-click on the maximum visible distance and enter the value in actual units.
  6. Enter the calibration setting and check the result. The program will save the calibration factor.
  7. You can select any measurement unit later, and all the results will be re-calculated by this selection.

CAMERA CONTROL PANEL
To open the Camera control panel, move the mouse cursor to the left of the window. The control panel will automatically pop up.

MAGUS-CHD30-Digital-Camera-fig- (3)

  • DC (Direct current) Allows you to use a light source without light flickering.
  • AC(50HZ) (Alternative current) Eliminates light flickering when a 50Hz light source is used.
  • AC(60HZ) (Alternative current) Eliminates light flickering when a 60Hz light source is used.
  • Default Restores the default settings.

MEASUREMENT TOOLBAR
To open the Measurement Toolbar, move the mouse cursor to the top of the window. The toolbar will automatically pop up. Select a figure to draw up; click at the desired initial point on the image, and click at the desired endpoint. The selected figure will be drawn up on the image and the figure parameters will be displayed.

MAGUS-CHD30-Digital-Camera-fig- (4)MAGUS-CHD30-Digital-Camera-fig- (5)

CAMERA CONTROL TOOLBAR
To open the Camera Control Toolbar, move the mouse cursor to the bottom of the window. The control toolbar will automatically pop up.

MAGUS-CHD30-Digital-Camera-fig- (5)

AUTOFOCUS СONTROL PANEL
Press the AF button to open the AutoFocus Control panel in the right part of the window and the rectangle Focus Region in the center of the image.

MAGUS-CHD30-Digital-Camera-fig- (7)

FOCUS REGION IN THE VIDEO WINDOW

MAGUS-CHD30-Digital-Camera-fig- (8)

The Focus Region is used to select the region of interest (ROI) for the autofocus operation. You can click any part of the video display window to change the focus region position for the Auto Focus operation. When you close the Auto Focus Control Panel, the Focus Region will also be closed automatically. If the Focus Region function is enabled, the Measurement Toolbar will not appear when the mouse cursor is moved to the top of the video display window.

SETTINGS

MAGUS-CHD30-Digital-Camera-fig- (9)

WI-FI
Channel: Avoids interference caused by using the same WiFi signal Channel. Suggests different channels for different cameras when several WiFi cameras are operated at the same time.
SSID: You can use the soft keyboard below to set the name of the WiFi signal.
Password: You can use the soft keyboard below to set the Password for the WiFi signal.
Default: Resets the Channel, SSID, and Password options to the default values.

MAGUS-CHD30-Digital-Camera-fig- (9)

MEASUREMENT
You can Left-click and select Measurement to open the corresponding window of settings. You can specify the parameters of the required measurement objects.

MAGUS-CHD30-Digital-Camera-fig- (11)

MAGNIFICATION

MAGUS-CHD30-Digital-Camera-fig- (12)

IMAGE FORMAT

MAGUS-CHD30-Digital-Camera-fig- (13)

VIDEO

MAGUS-CHD30-Digital-Camera-fig- (14)

STORAGE

MAGUS-CHD30-Digital-Camera-fig- (15)

You can also select a language from the list.

THE KIT INCLUDES
MAGUS microscope digital camera, 12V, 1A power adapter, HDMI cable, USB mouse, 32GB SD card, LM816 USB Wi-Fi adapter, USB flash drive with drivers and software, mounting plate and screws, user manual, and a warranty card.

SYSTEM REQUIREMENTS
Windows 8/10/11 (32bit and 64bit), Mac OS X, Linux, up to 2.8GHz Intel Core 2 or higher, minimum 4GB RAM, USB2.0 port, 19″ or larger display.

SPECIFICATIONS

MAGUS-CHD30-Digital-Camera-fig- (16)MAGUS-CHD30-Digital-Camera-fig- (17)

The manufacturer reserves the right to make any changes to the product lineup and specifications or discontinue the product without prior notice.

CARE AND MAINTENANCE

  • Do not disassemble the camera on your own.
  • Keep the camera away from moisture; do not use it in rainy weather.
  • Keep the camera away from shock or excessive pressure.
  • Do not overtighten the locking screws.
  • Keep the camera away from hazardous environments, home, and car heaters, incandescent lamps, or open fires.
  • When cleaning the lenses, first blow any dust or debris off the surface or wipe them off with a soft brush. Then wipe the lens with a soft cleaning cloth slightly damp with spirits or ether.
  • Seek medical advice immediately if a small part of a battery is swallowed.

MAGUS WARRANTY
MAGUS optic products carry a 5-year warranty against defects in materials and workmanship. All MAGUS accessories are warranted to be free of defects in materials and workmanship for six months from the purchase date. The warranty entitles you to the free repair or replacement of the MAGUS product in any country where a Levenhuk office is located if all the warranty conditions are met. For further details, please visit www.magusmicro.com If warranty problems arise, or if you need assistance in using your product, contact the local Levenhuk branch.

www.magusmicro.com
Levenhuk Inc. (USA):
928 E 124th Ave. Ste D, Tampa, FL 33612, USA,
+1-813-468-3001 contact_us@levenhuk.com

Documents / Resources

PDF thumbnailCHD30 Digital Camera
User Manual · CHD30 Digital Camera, CHD30, Digital Camera, Camera

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.