magivaac RV4500 LiDAR Scanning Robot Vacuum and Mop User Manual

Ensure the power cord is not damaged; if damaged, have it replaced by authorized personnel only.
Store the product in a cool, dry place and recharge it at least once every three months if not in use.

Product Maintenance

Remove the battery before disposing of the appliance following the correct procedure.
If transporting the product, make sure it’s turned off and use the original box.

Laser Safety
This product includes a Class 1 laser that complies with safety standards and does not produce dangerous laser radiation to the human body.

FAQ

Q: Can I use third-party batteries with this product?
A: No, it is not recommended to use third-party batteries with this product as stated in the safety precautions.

Q: How often should I replace the dust bags?
A: Dust bags should be replaced regularly as they cannot be recycled. It is advisable to replace them as needed to maintain optimal performance.

www.lenoxx.com.au

1300 666 848
Instagram: LenoxxEIectronics

Facebook: LenoxxEIectronics

Safety precautions

Usage restrictions

To avoid the danger of suffocation, keep all plastic bags away from babies and children.
This product is intended for household use only, not for outdoor surfaces (such as open balconies), non-floor levels (such as sofas), etc.

Do not use this product on a surface where there is no guardrail protection (such as duplex buildings, open balconies, and on top of furniture).
Do not use it in an environment where the temperature is higher than 40°C, lower than 0°C, or there are any liquids and viscous objects on the ground.

Before use, remember to lift any cables from the floor to prevent cable-related problems.
Please put away the fragile items and sundries placed on the ground (such as vases, plastic bags) to avoid the main machine being blocked or colliding during operation and causing damage to valuables.
Do not allow persons (including children) who lack physical, sensory and intellectual capacity or experience to use this product without supervision or guidance.
Do not let children use this product as a toy.
Do not place the cleaning tool of the main brush in a child-accessible area.
Do not let your hair, fingers and other parts close to the vacuum port of the machine when the machine is working.
Do not use this product to clean up any burning objects (e.g. unextinguished cigarette butts).
Do not let the host pick up hard or sharp objects (such as decoration waste, glass, iron nails, etc.).
Do not use the protective cover of the laser ranging sensor, the upper cover of the main unit and the collision buffer as a handle to carry the machine.
To clean and maintain the main unit and the charging dock with the dust box, first turn off the machine, pull out the plug from the socket, and disconnect the power supply. Do not immerse the main unit and the charging dock with the dust box into the water to wash or rinse it with water.
Do not wipe any part of the product with a damp cloth or any liquid.
Do not use the mopping mode on a carpeted floor.
Please use this product in accordance with the instructions in this manual. Any loss and damage caused by improper use shall be borne by the user.

Battery and charging

Incineration of the product is prohibited even if the product is severely damaged, as the battery of the product may explode.
Do not use any third-party batteries, chargers or charging docks.
Do not disassemble, repair or modify batteries and charging dock without permission.
Do not place the charging dock near heat sources (such as radiators).

Do not wipe or clean the electrode of the charging dock with a damp cloth or wet hands.
Do not throw away discarded batteries at will. Please send the battery to professional recycling organisations.
If the power cord becomes damaged, it should only be replaced by the manufacturer, the maintenance department, or an authorized service center.

If you need to transport the product, please make sure that the main unit is turned off, and it is recommended to use the original box.
Do not pour water into the device, or immerse the device in water
If the product is not being used for an extended period, ensure that you turn off the main unit after it’s fully charged. Store it in a cool, dry place, and remember to recharge it at least once every three months. This will help prevent battery damage caused by excessive discharge.

The battery must be removed from the appliance before disposing of the appliance.
To take out the battery, you need to use the correct tool. First remove the bottom battery cover screw, then open the product battery cover, unplug the battery connection terminal and take out the battery from the battery box.
The appliance must be switched off when the battery is being removed.

This product includes a Class 1 laser. The lidar of this product complies with the Class 1 laser safety standard of GB 7247.1-2012/1EC60825-1:2014, and will not produce dangerous laser radiation to the human body.

Packing list

The illustrations of products, accessories, user interface, etc. in this manual are schematic diagrams and are for reference only. Due to product updates and upgrades, the actual product may be slightly different from the schematic diagram, please refer to the actual product.

Accessories installed on the robot

Accessories installed on the charging dock with dust box Dust bag

Note: Dust bags cannot be recycled, please replace them regularly.

Product Parameters

Robot Vacuum Cleaner

Product name Robot Vacuum Cleaner
Model RV4500

Product size 345mm x 345mm x 76mm
Input DC 24V 0.6A
Rated power 50W

Working voltage 14.8V
Battery type Lithium-ion battery pack
Battery capacity 5200mAh

Wireless connection Wi-Fi IEEE 802.11b/n 2.4GHz

Charging dock with dust box

Output DC 24V 2A

Rated power 950W
Product size 260mm x 211mm x 347mm

Product introduction

Main machine

Power on/off/one key start and stop
- Press & hold key for more than 3 seconds to turn on or turn off the robot vacuum.
- Short press key to start cleaning or pause operation.LED indicator
  Green: normal operation/standby/charged
  Red: Low battery/fault alarm/charging

Automatic recharge/App distribution network
- Short press key to start/stop automatic charging.
  - Quick WiFi Network Setup: Press and hold the button for over 3 seconds, and the vacuum will emit a confirmation sound, signaling the start of rapid network distribution. The power button’s green light will flash rapidly, indicating entry into fast network configuration mode.
- App Hotspot Network Setup: Press and hold the button for over 6 seconds, and the vacuum will emit a second confirming sound. The voice prompt “Start AP network configuration” will follow, accompanied by the power button’s rapid green light flashing. This signifies that the vacuum has entered the app hotspot network configuration mode.

Indicator description

Auto disposal station with charging dock

Indicator description of auto disposal station
Charging dock status

Dust bags can be purchased from lenoxx.com.au/products/rv4500-dust-bags or by scanning the QR code:

Remote controller

Remote controller

Standby
Press this key to enter sleep mode; press key to restart the machine; If the machine is not operated within 3 minutes, it will automatically enter sleep mode.

Auto cleaning
Press this key to start cleaning automatically; Press to pause the machine if necessary.
Automatic charging
Press this key to automatically find the charging base for charging.
Pause
Press this key while the machine is operational to pause it. Press the key when the machine is in sleep mode to wake it up.

Direction

Forward	Press this key to move the machine forward.	Reverse	Press this key to move the machine back.
Left	Press this key to move the machine left.	Right	Press this key to move the machine right.

Suction power
During operation, press this button to select Quiet or Powerful suction.
Water volume control
During operation, press this button to control the volume of water used for mopping.

Auto disposal station with charging dock
Place the charging dock with dust box against the wall on a flat ground, insert the power plug into a socket that meets the requirements, and turn on the power.

Make sure that there are no obstacles within 1.2 meters in front of the charging dock with dust box and within 0.5 meters on both sides.

How to use

Charge the robot
Press and hold button for 3 seconds to turn on the robot, and then press button to make the robot automatically recharge. The robot will enter the ready-to-work state when fully charged.

Fully charge the robot before first use.
Before starting the cleaning task, tidy up the wires and items on the ground to avoid cable entanglement and collision in the cleaning process.
It is recommended that the robot starts cleaning task from the charging dock with dust box.

When the power is insufficient during the cleaning process, the robot will automatically return to the the charging dock with dust box. Once it has enough power, it will go back to where it stopped and continue cleaning.

Power on/Power off/Pause
Press and hold button for 3 seconds to turn on the machine. The power indicator’s green light will flash for 5 seconds, then remain on. The device will voice “Welcome to use our Robot vacuum cleaner, I am glad to serve you.” The robot will then be in standby mode. For default cleaning mode, press button. Alternatively, press and hold button for 3 seconds to activate the WIFI network. When the robot is stationary, press and hold the button for 3 seconds to turn off the machine, the power indicator light will turn off. During the cleaning process, press button to enter the recharge mode, and press button to pause the cleaning task. The robot will enter sleep mode if there is no operation for 10 minutes; in the sleep mode, short-press any button to wake up the machine.
During charging, the robot cannot be turned off and will not enter the sleep mode.

Automatic recharge/manual recharge
When the battery is low during cleaning, the robot will automatically start recharging. Once cleaning is complete, the robot will also automatically recharge. While cleaning, you can briefly press button to pause the robot. To return the robot to the charging dock with the dust box for both recharging and dust collection, simply give a short press to button.

Default cleaning mode
The default mode is the whole house cleaning mode. Once the app is connected, additional modes can be selected from within the application.

Pause robot for water tank refill or mop cleaning
Short-press button to pause the robot, remove the mopping module, add water or clean the mop, then install the mopping module back, and short-press button again to continue cleaning.

Robot status alerts and sleep mode

In case of robot malfunction, a voice prompt will sound, accompanied by a flashing red light on the power indicator. To resolve issues, consult the “Troubleshooting” section.
If no activity occurs for 10 minutes during a fault state, the robot will enter sleep mode automatically.

App connect
Scan the QR code below, or search for “Smart Life” app in the app store, download and install it. Open the app, click + icon in the upper right corner of the home page, and follow the prompts to add devices.

Due to upgrades and updates of the app, the actual operation may be slightly different from the above description, please operate according to the current instructions in the app.

Maintenance

Replace the dust bag
When the dust bag becomes full, the indicator light will turn white and stay on, while the app will also notify you. Make sure to replace the dust bag promptly.

Clear dust tube
If the indicator light of the charging dock with dust box is constantly red, it’s advised to disconnect the power plug, flip the dust box upside down, and inspect if any foreign objects are blocking the dust tube. If there’s a blockage in the dust tube, follow the diagram on the right to remove the dust tube’s transparent cover using a screwdriver, and clear away any foreign objects.

Handle the dust box with care.
Do not force disassembly or assembly.

After cleaning the dust tube, put it back in place.

Clean the infrared lens/sensor head
Wipe the infrared lens & sensor heads gently with a clean, soft, dry cloth. It is recommended to clean it once a month.

Clean the fan filter
The fan filter is located under the dust bag. When the dust accumulates, wipe it with a clean, soft dry cloth. It is recommended to clean it once a month.

Clean the main brush
The main brush is a consumable item and should be cleaned at least once a week. It is recommended to replace the main brush every 6 or 12 months to ensure the cleaning quality.

Flip the robot, then press the latch on the main brush cover to remove both the cover and the main brush.

Use a cleaning tool to cut the entangled hair on the main brush, and use the cleaning brush on other end of the cleaning tool to clean the main brush.

Clean/replace the side brush
Remove the side brush.

Install the side brush back in place after cleaning, or install a new side brush.

The side brush is a consumable item. Please replace it every 3-6 months to ensure the cleaning quality.

Cleaning the sensor

It is recommended to gently wipe each sensor with a clean, soft, dry cloth every week to ensure normal use of the machine.

Robot vacuum cleaner:

Cliff sensor x4
Charging sensor x2
Laser obstacle sensor x3

Laser range sensor x1

Battery Maintenance

The robot has a built-in high-performance rechargeable lithium-ion battery pack. For optimal battery performance, keep the battery charged at all times.

When the machine won’t be used for an extended period, turn it off, store it, and make sure to recharge the battery at least every three months to prevent overdischarge damage.

Clean 2-in-1 water tank
Press and hold the release button of the 2-in-1 water tank, and simultaneously pull it out.

Press the buckle of the dust box to open the dust box.

Use a cleaning brush to remove debris from the filter and filter holder.

Clean the dust box with running water.

The filter is a consumable item. It is recommended to replace it every 3-6 months.
Open the cover of the water tank and add water.

Purified water is recommended.

Turn the 2-in-1 water tank over and remove the mop for replacement or cleaning.

Always start mopping with a clean mopping pad. A dirty mopping pad will affect mopping effectiveness.
Remember to remove the mopping pad for cleaning and let it dry before putting it back. Avoid cleaning it while it’s connected to the 2-in-1 water tank to prevent the filter element from becoming blocked with dirty water.
Consider replacing the mopping pad every 3 months to maintain cleaning quality.

Troubleshooting

In case of robot malfunction the power indicator will flash red. Additionally, the robot will provide voice prompts for certain faults. Consult the table below to troubleshoot and address the problem.

When an abnormality occurs during the operation of the auto disposal station with charging dock, the corresponding icon on the display screen of the auto disposal station with charging dock will light up, and the app will also prompt you. Please refer to the below table to try to solve it.

APP Operation Guide

Turn on the phone camera, scan QR code to download the ” Smart Life” APP.
Search “Smart Life” in Apple and Google or Samsung application market And download the APP.
Before using this feature please make sure Your phone has been successfully connected 2.4G WiFi and turn on the phone “BLE”.

Open the app “Smart Life” to log in and then click on “App Device”.
Connect WiFi (confirm 2.4Ghz) and turn on Bluetooth
Power on the robot, press and hold the auto charging button for more than 4 seconds, until the robot sends out a voice prompt “Start AP Network distribution”. The button indicator light turns green and starts to breathe, and the device starts network distribution mode;
proceed to the next step “AddDevice”,Or click the “+” logo in the upper right corner and Add Device,As shown in the picture, the robot is ready to connect to the device via bluetooth
Wi-Fi connection method：Select and click on “small Home Appliances”and Robot Vacuum(BLE+ -Wi-Fi)
Make sure the name of your home WiFi, and enter the WiFi password and click on NEXT (note: only 2.4G WiFi is available), as shown in the figure.
After hearing the voice prompt, click on “Next” when power button flashes slowly. Note, as shown in the figure, you can choose Bluetooth or WiFi connection mode
To connect your mobile phone to the device’s hotspot, choose the hotspot named as “SmartLife” to connect to the network.
After the hotspot “SmartLife” is connected, return to the app interface to start connecting to the device. Please ensure that thegreen light button flashes and that the Wi-Fi must be 2.4 Ghz(Notice: this device cannot be connected to 5G network). After the device is bound successfully,the following control interface pops up.
Click on “Robot vacuum” to entry the interface as shown below;
Remove the device: long press the device ID and click on “Remove Device” to remove the device(repeat the procedures above to reconnect the device if necessary);
Set up Scheduled clean: open the main interface of the app – Settings – Timer – Add to – Set a time – Save.
Auto clean
Click this button to automatically create a new cleaning mission, and the robot will efficiently sweep the area. After the sweeping is finished, the robot will automatically return to the charging dock for charging.
selected zone cleaning
- Choosing this button to start a select area clean.
- Touch the map to select area will highlight, can setup one or more areas to clean as designated.
configured zone cleaning
- Click on “Zone clean” on the app.
- Clickon “configured zone cleaning”on the app.Click “Add Zone”, a virtual box is seenon the map.Move the box to the aretfor sweeping. click ordesignated-Start” and the robot will move to thearea designated to sweep the area
Prohibition/Virtual wall
You can use the APP to set the no-go zone, and you can set one or many no-go zones. The robot vacuum cleaner will not clean the set no-go area and only clean other areas.
Y-MOPPING
Install the water tank and mopping pad click the “Auto clean” after the robot starting moping then click “setup”. Turn on the “Y-MOPPING” button on the setting page of the APP, the robot will start mopping the floor in “Y” shape pattern.

RV4500 Rooms Edit Steps

When the robot finish mapping, it will automatically separate the rooms and do cleaning room by room. But if you want to edit the rooms by manual, please follow the below steps.

Separate Rooms
Open the map on App, click on “Map Edit”, then click on “Map Custom Editing”, then you can select a tool type such as “Split”, then choose a room on map and draw the line by hand, so one room will be separated in two rooms.

Edit Rooms Cleaning
Open the map on App, click on “Map Edit”, then click on “Map Custom Editing”, then you can select tool type “Order”, then click the rooms one by one on map in sequence and save your order, so the robot will do cleaning room by room based on your custom room order.

Documents / Resources

magivaac RV4500 LiDAR Scanning Robot Vacuum and Mop [pdf] User Manual
RV4500 LiDAR Scanning Robot Vacuum and Mop, RV4500, LiDAR Scanning Robot Vacuum and Mop, Robot Vacuum and Mop, Vacuum and Mop

References

User Manual

magivaac RV4500 LiDAR Scanning Robot Vacuum and Mop

Product Information

Product Usage Instructions