M5Stack Technology Co Ltd CardputerZero Linux Pocket Computer User Manual
Description
CardputerZero is a pocket-sized Linux personal computer designed for makers and developers, built on the Raspberry Pi CM0 platform. It integrates a quad-core Cortex-A53 processor, a 1.9-inch display, a 46-key matrix keyboard, an 8MP camera, an IMU, and an RTC, delivering a near-complete development terminal experience in a handheld form factor. It also features Wi-Fi, Bluetooth, Ethernet, microSD, a switchable Host/Slave USB architecture, and modular expansion capabilities via I2C/UART/SPI/GPIO. Combined with audio/video codec support and a battery-powered design, it enables an all-in-one solution for on-the- go development, edge data collection, and multimedia interaction. Typical use cases include: mobile penetration testing and operations terminals, IoT device debugging and field deployment, portable AI/vision prototyping, maker project development, and outdoor data collection with rapid human-machine interaction. The board also uses a 25 MHz crystal X1 (XL7EL89CKI-111YLC-25M) as the reference clock for the SR9900A USB-to-Ethernet controller and a 12 MHz crystal X2 (X252012MMB4SI-24) as the reference clock for the GL852G USB 2.0 hub.

Specifications
| Specification | Parameters |
| Core | Raspberry Pi Compute Module 0 (CM0) |
| CPU | RP3A0 (BCM2837), Quad-Core Cortex-A53 @ 1 GHz, ARMv8-A (aarch64) |
| RAM | 512 MB LPDDR2 |
| Wireless | 2.4 GHz Wi-Fi 802.11 b/g/n; Bluetooth 4.2 (BR/EDR + BLE) |
| Ethernet | 10/100M Ethernet, SR9900A USB 2.0 to Ethernet chip |
| Display | 1.9″ LCD @ ST7789v3, resolution 170×320 |
| Camera | IMX219 CSI 4-Lane 8MP (3280 x 2464) |
| Keyboard | 46-key matrix keyboard46-key matrix keyboard |
| Expansion Interface | EXT 2.54-14P expansion bus, 1x HY2.0-4P port |
| USB Hub Chip | GL852G-OHY60 USB 2.0 Hub |
| Idle Power Consumption | 2.5W |
| Built-in Battery | DC 3.7V @ 1750mAh with integrated NTC |
| Power Supply | Recommended 5V @ 2A for power/charging |
| Product Size | 84.0 x 54.0 x 23.1mm |
Quick Start
3.1 Preparation Reference the CardputerZero Image Flashing Tutorial to complete the image flashing process. After startup, follow the on-screen prompts to configure the Wi-Fi connection. https://docs.m5stack.com/en/guide/linux/cardputerzero/image
3.2 Bluetooth (BLE) Configuration The CardputerZero supports Bluetooth 4.2 (BLE). Bluetooth can be configured through the standard Linux command-line tool bluetoothctl:
- Open a terminal and run sudo bluetoothctl to enter the Bluetooth console.
- Initialize Bluetooth and scan for nearby BLE devices: power on, agent on, default-agent, scan on
- Find the target device in the scan results and pair with it: pair
- After pairing, run trust and connect to establish the connection.
- Enter quit to exit the Bluetooth console.
FCC Warning
FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The device has been tested and comply with FCC SAR limits.
Company Name:M5Stack Technology Co.,Ltd
Address: Block A10, Expo Bay South Coast, Fuhai Street, Bao’an District, Shenzhen,Guangdong,China
Documents / Resources
![]() | CardputerZero Linux Pocket Computer |
References
- m5-docsdocs.m5stack.com
- User Manualmanual.tools
