Anko Bluetooth Tripod Party Speaker with RGB

Warning

• The apparatus shall not be exposed to dripping or splashing, and no objects filled with liquids, such as vases, shall be placed on the apparatus.
• Leave a minimum distance of 100cm around the speaker for sufficient ventilation.
• The ventilation should not be impeded by covering the ventilation opening.
• Keep the device away from flames and other heat sources.
• When the mains plug or appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
• Working temperature: -10℃ to +45℃.
• The use of apparatus in moderate climates.
• Do not use this apparatus near water.

Battery Information

• Disposal of this product and the battery should be in accordance with local government requirements.
• Battery cannot be subjected to high or low extreme temperatures, or low air pressure at high altitude during use, storage, or transportation.
• Replacement of a battery with an incorrect type that can result in an explosion or the leakage of flammable liquid or gas.
• Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
• Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
• A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
• Batteries shall not be exposed to excessive heat such as sunshine, fire, or the like.
• The internal battery is non-user replaceable.

Product Features

• 3 lighting effects.
• Bluetooth version 5.0, compatible with audio devices with Bluetooth function, such as MP3/4, mobile, computer, iPad.
• Built-in rechargeable lithium battery.

Speaker and Tripod Setup

Unfolding the Tripod

To unfold the tripod:

1. Turn the thumb screw handle on the tripod base counterclockwise until the tripod is able to open.
2. Holding the center column firmly in one hand, grip and carefully pull one of the legs outward until the tripod begins to unfold, and the center column sides up.
3. Push the center column up until the tripod is fully opened and the center column cannot be pushed up any more.
4. Turn the thumb screw handle clockwise until tight.

Adjusting the Tripod's Height

To adjust the tripod's height:

1. Turn the two thumb screw handles on the upper part of the tripod's center column counterclockwise until loose.
2. Raise or lower the adjustable center rod to the desired height, and insert the pin to fix the height.
3. Turn the thumb screw handles clockwise until tight to secure.

Mounting the Speaker

To mount the speaker onto the tripod:

1. Unfold the tripod and adjust it to the desired height.
2. Align the mounting hole on the bottom of the speaker with the rod of the tripod, and turn the thumb screw handle on the speaker clockwise until tight to secure the speaker.

NOTE:

• Please use and place the tripod on a flat ground to avoid unbalanced placement.
• When the speaker and the tripod are used together, please ensure all knob screws are tightened on both.
• Do not place speakers with different mounting hole sizes onto the tripod. The maximum diameter of the speaker's mounting hole is 3.5cm, which may cause unstable placement and product fall.
• The tripod stand height is up to 120cm. It is recommended to use it at around 0.8m; too high may cause it to fall.
• Please take care to prevent children from touching or playing with the tripod to avoid accidental tipping.

Button and Interface Description

The speaker features a control panel with the following numbered inputs and controls:

1. MIC Input: Insert the wired microphone here.
2. Mic Volume: Microphone volume adjustment knob.
3. Echo Volume: Echo volume adjustment knob.
4. Next Key: Press to go to the next track in Bluetooth/USB sources, or to go to the next channel (CH+) in FM source.
5. Play/Pause Key: Short press to play or pause the track in USB or Bluetooth modes. Long press to turn on TWS pairing function in Bluetooth mode.
6. Previous Key: Press to go to the previous track in USB or Bluetooth mode, or to go to the previous channel (CH-) in FM mode.
7. MODE/LIGHT Key: Short press to change function modes (Bluetooth, FM, AUX, USB/TF). Long press to switch LED light effects and turn the lights off.
8. POWER/VOLUME Knob: Turn clockwise to power ON/OFF. Turn to adjust volume.
9. TF Card Input: Insert a TF card to play tracks.
10. USB Input: Insert a USB driver to play tracks.
11. Aux Input: Insert a 3.5mm AUX cable.
12. DC Input: For charging the speaker.

Operation

Powering ON/OFF

1. Ensure the speaker has been charged.
2. Turn the [ POWER/VOLUME ] knob clockwise until it clicks to power ON. The speaker will enter Bluetooth pairing mode.
3. The speaker may automatically re-pair to any nearby, previously paired device.
4. Turn the [ POWER/VOLUME ] knob counterclockwise until it clicks to power OFF.

Charging the Speaker

The speaker has a built-in rechargeable battery. To charge it:

1. Plug one end of the USB charging cable (included) into the DC 5V input slot and the other end into a USB charger (not included) or a wall outlet.
2. The battery indicator on the back will show RED while charging and turn off when fully charged.
3. When the speaker battery is low, a "DIDIDI" tone will be heard, indicating it needs charging.

Changing Function Modes

1. Press the [ MODE/LIGHT ] button to switch function modes.
2. The LED screen on the speaker will indicate the selected mode.
3. Note: You must have a micro TF card or USB device inserted, or an AUX cable connected, to switch to these modes.

Adjusting Volume & Playback

1. Adjust the volume using the [ POWER/VOLUME ] knob or the controls on a connected device.
2. Press the [ Previous Key ] and [ Next Key ] buttons on the speaker to switch tracks in Bluetooth/USB mode or stations in FM mode.
3. Press the [ Play/Pause Key ] button to pause and resume playback in Bluetooth/USB mode.

Switching the Speaker Light Effects

1. The LED light effect will automatically turn on when the speaker is powered on.
2. Long press the [ MODE/LIGHT ] button on the back of the speaker to cycle through LED light effects or turn the lights off.

Using the FM Radio

(The FM Antenna cable is the same as the AUX cable, included)

1. Power on the speaker and switch to FM mode. The LED screen will display the current FM frequency.
2. Insert the FM/AUX cable into the AUX jack (which also serves as the FM antenna).
3. Long press the [ Play/Pause Key ] button to start scanning and saving available stations. The LED screen will show the scanning progress.
4. Press the [ Previous Key ] and [ Next Key ] buttons to switch between the saved stations.

Connecting to an AUX Device

Insert one connector of the 3.5mm AUX cable (included) into the 3.5mm AUX input jack on the back of the speaker. Insert the other connector into the headphone jack or audio output jack of your media playing device. The LED screen will display "AUH". In AUX mode, all playback will be controlled by your connected device.

Connecting with Bluetooth

1. Power on the speaker. The LED screen will display "bLUE".
2. Open Bluetooth on your mobile device and search for the Bluetooth name "43430888" to pair.
3. In Bluetooth mode, playback and volume can be controlled by your paired device or the controls on the back of the speaker.

TWS Connecting

*This speaker supports TWS (True Wireless Stereo) pairing function. Please purchase two identical speakers to enjoy this feature.

1. Long press the [ Play/Pause Key ] button on two speakers to turn on the TWS pairing function. You will hear a "DI" sound from the speaker, and "TWS" will briefly display on the screen.
2. The TWS will pair automatically once both speakers have the TWS function enabled.
3. Turn the volume knob on the back panel of either speaker to increase or decrease the music volume for both.
4. *Please ensure both speakers' volume levels are set the same to avoid intermittent sound during playback.
5. If you are not using the TWS function, please long press the [ Play/Pause Key ] button again to disconnect TWS.

Connecting to Wired Microphone

Insert a 6.35mm wired microphone and use the control knobs to adjust the sound level. When playing with the wired microphone, use the MIC Volume knob and Echo Volume knob to adjust the microphone's volume and echo effect.

Product Specification

12 Month Warranty

This product is covered by a 12-month warranty from the date of purchase. This warranty covers manufacturing defects and faulty workmanship. It does not cover damage caused by misuse, accident, modification, or unauthorized repairs.

For warranty claims, please retain your proof of purchase. Contact the retailer or manufacturer for assistance.

Contact Information

Contact for Team Purchases

Anko Retail Pty Ltd

PO Box 1376

North Sydney NSW 2059

Australia

Website: https://www.anko.com.au

Contact for Target Purchases

Target Australia Pty Ltd

200 Bourke Street

Melbourne VIC 3000

Australia

Website: https://www.target.com.au