Installation Guide for EDiMAX models including: ES-3305P, ES-3308P, ES-3316P, ES-3305P 5 Port Fast Ethernet Desktop Switch, 5 Port Fast Ethernet Desktop Switch, Fast Ethernet Desktop Switch, Ethernet Desktop Switch, Desktop Switch, Switch
Edimax ES-3305P, 100 Mbps, 5 x RJ45 ▻ Сетевой коммутатор, 100 Mbps, 5 x RJ45 ▻ купить в GEEK.MD
File Info : application/pdf, 10 Pages, 217.96KB
DocumentDocumentES-3305P / ES-3308P / ES-3316P Quick Installation Guide 11-2020 / v1.2 PRODUCT INTRODUCTION Model: ES-3305P: 5 Port Fast Ethernet Desktop Switch ES-3308P: 8 Port Fast Ethernet Desktop Switch ES-3316P: 16 Port Fast Ethernet Desktop Switch Package Contents Before you start using this switch, please check if there is anything missing in the package, and contact your dealer to claim the missing item(s): Fast Ethernet Desktop switch Quick Installation Guide Power Adapter Front Panel ES-3305P PWR LED LNK/ACT LEDs 1 - 5 ES-3308P PWR LED LNK/ACT LEDs 1 - 8 1 ES-3316P PWR LED LNK/ACT LEDs 1 - 16 LED Status: LED Name Light Status PWR On Off On LNK/ACT Off Flashing Description Switch is on Switch is off Corresponding port is connected Corresponding port is not connected Corresponding port is active and transferring /receiving data. Back Panel ES-3305P RJ-45 Ports 1 - 5 5V DC Power Port ES-3308P RJ-45 Ports 1 - 8 2 5V DC Power Port ES-3316P 5V DC Power Port RJ-45 Ports 1 - 16 Operating Environment This switching hub must be installed and operated within the limits of the specified operating temperature 0~40°C (32~104°F) and humidity (10~90% Non-condensing). - Do not place objects on top of the unit. - Do not obstruct any vents at the sides of the unit. - Do not position the unit near any heating source such as a heater, radiator or in direct exposure to sun. - Take care to ensure the unit does not come into contact with water. Consider using a dehumidifier to reduce humidity and prevent moisture entering the unit. 3 Connecting to network devices The RJ-45 ports on the switch support Auto-MDI/MDI-X which allows both straight-through or cross-over type cables to connect this switch to a workstation or hub. Connect one end of the network cable to the RJ-45 port on the rear panel, and connect the other end of the network cable to the RJ-45 port on the network device. Follow the same procedure to connect all RJ-45 ports of the switch. The UTP network cables must comply with EIA/TIA 568 specifications and Category 5 standard for data transmission. The maximum length for a UTP cable segment between the switch and connected devices is 100 meters (300ft). Once the network cable is connected to both ends and the attached network device is powered on, the green LNK/ACT LED should be lit. 4 Connecting the power Connect the power adapter to the power connector of the unit; the green power LED on the front panel should be lit. ES-3305P/ES-3308P ES-3316P TROUBLESHOOTING 1. Power LED is not lit Check if the power cord is properly connected to the external power adapter and the power source. Make sure the DC power jack is firmly plugged into the power socket of the switch. 2. Link/Activity is not lit when connected to devices - Ensure that the network device attached to the switch is switched on. - Check the network cable; ensure it is properly connected to the switch and the network device. - Check the network cable; ensure the UTP cable complied with EIA/TIA 568 and Category 5 specifications. [!] Contact your dealer if problems persist. 5 COPYRIGHT Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd. makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability, or fitness for any particular purpose. Any software described in this manual is sold or licensed as is. Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Edimax Technology Co., Ltd. reserves the right to revise this publication and to make changes from time to time in the contents hereof without the obligation to notify any person of such revision or changes. The product you have purchased and the setup screen may appear slightly different from those shown in this QIG. The software and specifications are subject to change without notice. Please visit our website www.edimax.com for updates. All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders. 6 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio technician for help. FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no-collocation statement. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution! Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000. Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment. EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria, Belgium, Bulgaria, Cyprus, Czech, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Turkey, and United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein, Norway, and Switzerland. EU Countries Not Intended for Use None 7 EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/30/EU. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la Cestina: Polski: Român: directive 2014/30/EU. Toto zaízení je v souladu se základními pozadavky a ostatními píslusnými ustanoveními smrnic 2014/30/EU. Urzdzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi warunkami okrelonymi Dyrektyw UE 2014/30/EU. Acest echipament este în conformitate cu cerinele eseniale i alte prevederi relevante ale Directivei 2014/30/EU. : 2014/30/EU. Magyar: Ez a berendezés megfelel az alapvet követelményeknek és más vonatkozó irányelveknek (2014/30/EU). Türkçe: Bu cihaz 2014/30/EU. direktifleri zorunlu istekler ve dier hükümlerle ile uyumludur. : 2014/30/EU. Slovencina: Toto zariadenie spa základné poziadavky a alsie príslusné ustanovenia smerníc 2014/30/EU. Deutsch: Dieses Gerät erfüllt die Voraussetzungen gemäß den Richtlinien 2014/30/EU. Español: El presente equipo cumple los requisitos esenciales de la Directiva 2014/30/EU. Italiano: Questo apparecchio è conforme ai requisiti essenziali e alle altre disposizioni applicabili della Direttiva 2014/30/EU. Nederlands: Dit apparaat voldoet aan de essentiële eisen en andere van toepassing zijnde bepalingen van richtlijn 2014/30/EU. Português: Este equipamento cumpre os requesitos essênciais da Directiva 2014/30/EU. Norsk: Dette utstyret er i samsvar med de viktigste kravene og andre relevante regler i Direktiv 2014/30/EU. Svenska: Denna utrustning är i överensstämmelse med de väsentliga kraven och övriga relevanta bestämmelser i direktiv 2014/30/EU. Dansk: Dette udstyr er i overensstemmelse med de væsentligste krav og andre relevante forordninger i direktiv 2014/30/EU. suomen kieli: Tämä laite täyttää direktiivien 2014/30/EU. oleelliset vaatimukset ja muut asiaankuuluvat määräykset. ------------------------------------------------------------------------------------------------------------------- WEEE Directive & Product Disposal At the end of its serviceable life, this product should not be treated as household or general waste. It should be handed over to the applicable collection point for the recycling of electrical and electronic equipment, or returned to the supplier for disposal. 8 Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European R&TTE directives. Equipment: 5 / 8 / 16-Port Fast Ethernet Desktop Switch Model No.: ES-3305P / ES-3308P / ES-3316P The following European standards for essential requirements have been followed: Directives 2014/30/EU EMC : EN 55032:2015+AC:2016 EN 61000-3-2:2014 EN 61000-3-3:2013+A1:2019 EN 55035:2017 Directives 2014/35/EU Safety (LVD) : IEC 62368-1:2014 (2nd Edition) and/or EN 62368-1:2014+A11:2017 Edimax Technology Europe B.V. Fijenhof 2, 5652 AE Eindhoven, The Netherlands Printed Name: David Huang Title: Director Edimax Technology Europe B.V. a company of: Edimax Technology Co., Ltd. No. 278, Xinhu 1st Rd., Neihu Dist., Taipei City, Taiwan Date of Signature: Nov., 2020 Signature: Printed Name: Title: Albert Chang Director Edimax Technology Co., Ltd. 9
EDIMAX - Netwoking Solution Provider including SMB Wi-Fi Access Point, AP Controller, SMB and Industrial PoE++ L2+ Switch, Industrial Embedded Wirless (Wi-Fi, Bluetooth) USB Dongle (Adapter), Wi-Fi Smart Plug, IoT, Smart HomeEDIMAX - Netwoking Solution Provider including SMB Wi-Fi Access Point, AP Controller, SMB and Industrial PoE++ L2+ Switch, Industrial Embedded Wirless (Wi-Fi, Bluetooth) USB Dongle (Adapter), Wi-Fi Smart Plug, IoT, Smart Home