User Manual for SILVER STAR models including: SS9451SCM, SS9451SCM Moving Head Beam, SS9451SCM, Moving Head Beam, Head Beam, Beam
L8 FORUM - View topic - SILVER STAR BX SS9451SCM
File Info : application/pdf, 16 Pages, 1.93MB
DocumentDocumentBX USER MANUAL BX SS9451 MODEL: SS9451SCM 1 PRODUCT 1.1 TECHNICAL SPECIFICATIONS Type LED colors Angle Power Control Protocol Voltage Range Frequency Range Input Current Protection Operation Temperature Dimensions Weight SS9451SCM 100W Laser source 0.7° - 5° 200W DMX512/RDM/ARTNET/sACN/NFC/ Bluetooth/W-DMX(Optional) 100-240V~ 50/60Hz 110V/2A,220V/1A IP65 -20~45 416x358x712mm 26.7kg DIMENSIONS 1 1.2 Safety Notes IMPORTANT This product must be installed by a qualified professional. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to the device. CAUTION! Make sure that the available voltage is not higher than stated on the rear panel. Do not touch the power cables if your hands are wet. The earth wire must always be connected to the ground. Therefore it is essential to connect the yellow/green conductor to earth. Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the power-cord from time to time. The electric connection, repairs and servicing must be carried out by a qualified employee. Always disconnect power input cable to completely remove power from unit when not in use or before cleaning or servicing the fixture. Do not switch the fixture on and off in short intervals as this would reduce the lamp's life. Do not touch the device's housing bare hands during its operation (housing becomes hot)! The surface of the product's casing can reach up to 70° C (158° F) during operation. Avoid contact by persons and materials. Do not install the product in a location where there is a risk of accidental contact. Allow the product to cool for at least 10 minutes before handling. For replacement use lamps and fuses of same type and rating only. Please protect the fixture and avoid destroy during transport and installation. If there is any damage to the coating, the shell may be corroded. When hanging lamps and lanterns, it is necessary to verify that facilities and hooks can bear at least 10 times the weight of lamps and lanterns. Fix the safety rope at the correct holes only. Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened. The maximum ambient temperature 45°C must never be exceeded. Do not operate the product if the ambient temperature (Ta) exceeds 45° C (115° F). During the initial start-up some smoke or smell may arise. This is a normal process and does not necessarily mean that the device is defective. Electrical Warning The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person For replacement use lamps and fuses of same type and rating only. The lens has to be replaced when it is obviously damaged, so that its function is impaired, e. g. due to cracks or deep scratches! 2 Keep the product well away from flammable materials Keep all combustible materials (e.g. fabric, wood, paper) at least 20m (65.6 feet) away from the product. Ensure that there is free and unobstructed airflow around the product. Provide a minimum clearance of 500 mm (20 in.) around fans and air vents. Do not illuminate surfaces within 20 m (65.6 feet) of the product. Do not install a fuse that has a higher rating than the one originally installed in the product. Do not bypass fuses. Do not stick filters, masks or other materials onto optical components. If the fixture seems to be abnormally hot, shows signs of melting or emits smoke, disconnect the fixture from power immediately and allow it to cool. Do not touch the fixture without heatproof safety gloves. Keep the fixture well away from combustible and flammable materials. NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE! RETINA INJURY RISK - MAY INDUCE BLINDNESS! Do not point the front of the fixture towards the sun or other strong light sources. The front lens focuses and concentrates light just like a magnifying glass. Strong light can cause internal damage to the fixture, melting components or starting an internal fire within seconds. To avoid problems from strong light sources: Do not expose the front of a fixture to sunlight or any other strong light source. Avoid pointing other high-powered beam lights directly at the fixture. Do not focus a light beam from one lighting fixture directly towards another. For outdoor applications during daylight, make sure that the front face of any fixture is shielded or points away from the sun, even when not in use. Do not expose the product to heat (from other lighting fixtures for example). 3 2 INSTALLATION 2.1 MOUNTING Truss installation Keep all combustible materials (e.g. fabric, wood, paper) at least 500 mm (20 in.) away from the product. For overhead use, always install a safety cable that can hold at least 10 times the weight of the fixture. For overhead installation, the fixture must be always secured with a safety wire that can bear at least 10 times the weight of the fixture Secure the fixture with a safety cable through the rear safety eye and truss as shown.. Ensure that the structure (truss) to which you are attaching the fixture is secure 2.2 Fuse replacement Remove the safety cap by a screwdriver. Fetch the old fuse from safety cap. Install a new fuse. Install the safety cap. 4 2.3 POWER CONNECTIONS This product has an auto-ranging power supply that can work with an input voltage range of 100240 VAC, 50/60 Hz. AC Plug Connection Wire (U.S.) Wire(Europe) Screw Color AC Live Black Brown Yellow/Brass AC Neutral White Blue Silver AC Ground Green/Yellow Green/Yellow Green 2.4 Data network requirements Connect the DMX512 controller to the units in series. A DMX 512 data link is required in order to control the fixture via DMX. The fixture has 3/5-pin XLR connectors for DMX data input and output. Each unit has N DMX channels so the DMX Addresses should increase by increments of 1 (Nx1)+1(Nx2)+1(Nx3)+1... Any DMX address in the range from 001 to 512 may be used. Connect the DMX-output of the first fixture in the DMX chain with the DMX-input of the next fixture. Always connect one output with the input of the next fixture until all fixtures are connected. Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a 120 resistor between Signal () and Signal (+) into a 3/5-pin XLR-plug and plug it in the DMX-output of the last fixture. 5 3 FUNCTIONS AND SETTINGS 3.1 DISPLAY OPERATION LEFTUsed to access the menu or to return a previous menu option; RIGHTUsed to select and store the current menu or confirm the current function value or option within a menu; UPNavigates downwards through the menu list and increases the numeric value when in a function; DOWNNavigates upwards through the menu list and decreases the numeric value when in a function When the display locked, please unlock the display as below: 1. Keep pressing BACK around 5sec, until the display shows inset password. 2. Press "up down up down, enter" to unlock. 3.2 Menu Map ADDRESS 001 512(Default 001) PERSON BASIC STANDARD (Default) EXTEND RUNMODE DMX512 (Default) ARTNET ARTNET TO DMX sACN AUTO CUSTOM1 CUSTOM2 OPTION PAN INVERT NORMAL (Default) INVERT TILT INVERT NORMAL (Default) INVERT STUDIO PERFORM POWER LIVE (Default) BLACKOUT OFF (Default) 6 DMX address setting Use the menu to select desired channel mode Select Signal Default: DMX512 ARTNETEthernet control CUSTOM1-2 Set up get into EDIT MENU edit PAN moving direction selection TILT moving direction selection Fan mode low speed Fast rotation of fanall power Automatic rotation of fan Select OFF blackout without delay ON Select ON Blackout delay 3s DIMMER Halogen (Default) Dimming speed LED (fast) to Halogen SPEED LED (slow) LINEAR Sets the Dimmer curve DIMMER SQUARE LAW CURVE INV. SQUARE LAW S-CURVE LED PWM 1200Hz (Default) 2400Hz 4000Hz 6000Hz 25000Hz Sets the PWM frequency DMX ERROR SAVE (Default) BLACK Hold after loss of DMX signal Blackout after loss of DMX signal On Display backlight always on DISPLAY TIME 30s 1min (Default) Turns off display backlight after 30s/1min 2min /2min of inactivity OFF DISPLAY LOCK ON (Default) Locks display (passcode is <UP>, <DOWN>,<UP>, <DOWN>, <ENTER>) LOAD PARA OFF ON (Default) Not upload data Upload data RECOVERY **** Restore default factory settings. CLEAN **** EDIT1 Clean customer self-editing scene 1 CLEAN SETTING **** EDIT2 Clean customer self-editing scene 2 NO Hide wireless mode WDMX reset and WDMX HIDE YES signal hide and the default is wired mode only 2.xxx.xxx.xxx NET SWITCH 10.xxx.xxx.xxx Net switch off IP mode Net switch on IP mode NETWORK UNIVERS IP MODE 0-255 DEFAUL IP CUSTOM IP Packet group Settings Default IP Customer's IP CUSTOM IP XX.XX.XX.XX Customer's IP setting WIFI STATION WiFi settings MODE AP WIRELESS WIFI WIFI INTO SSID PASSWORD LOCAL IP YJSS9451 yj000001 xxx:xxx:xxx :xxx 7 EDIT MANUAL PT ENCODER LANGUAGE WDMX RESET SIGNAL EDIT 1-2 AUTO TEST CHANNEL REMOTE_IP MAC WIFI RESTART WIFI DEFAULT BLUETOOTH MAC NAME xxx:xxx:xxx :xxx xx:xx:xx:xx :xx:xx NO YES NO YES xx:xx:xx:xx :xx:xx YJSS9451 OFF XY Encoder switch. ON OFF is close; ON is open. Chinese **** ENGLISH LANGUAGE NO Do not clear the receiver's message. YES Clear the receiver's message ONLY XLRDMX ONLY XLR is wire only XLRDMX FIRST XLR FIRST is wire first ONLY WDMX ONLY WDMX is wireless only WDMX FIRST WDMX FIRS is wireless first WDMX TO XLRDMX WDMX TO DMX is wireless to wired PAN 0-255 Edit the custom programs1-30 TILT PT SPEED 0-255 0-255 Select play EDIT 1 in RUNMOEDE CUSTOM 1; Select play EDIT 2 in CMY_C 0-255 RUNMOEDE CUSTOM 2 CMY_M 0-255 CMY_Y 0-255 COLOR 0-255 ROTA.GOBO 0-255 STEP 1-30 GOBO.ROTA FIXED GOBO 0-255 0-255 PRISM 1 0-255 PRISM 2 0-255 FROST 0-255 FOCUS 0-255 DIMMER 0-255 STROBE 0-25 TIME 0-255 USE YES/NO Select YES to run the steps user need. PAN 0-255 Manual control channel 8 INFO DEBUG HIDE TILT PT SPEED CMY_C CMY_M CMY_Y COLOR ROTA.GOBO GOBO.ROTA FIXED GOBO PRISM 1 PRISM 2 FROST FOCUS DIMMER STROBE YES NO 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-25 ALL RESET RESET PT RESET COLOR SYSTEM OTHER FIXTURE HOURS LED USE HOURS TEMPERATURE VERSION NETWORK RDM UID LABEL 0x388Axxxxxxxx MEMORY IC ANGLESENSOR PAN SENSOR PAN ENCODER PAN DRIVEIC SYSTEM ERROR TILT SENSOR TILT ENCODER TILT DRIVEIC TEMPERATURE CMY_C RESET CMY_M RESET CMY_Y RESET COLOR RESET 9 Factory testing mode. All stepper motors are not controlled by signal, It only works again after the reset. Select Yes/No to carry out all reset Select Yes/No to carry out P/T reset COLOR/CTO reset Focus GOBO reset Hours of fixture use LED use time LED temperature Software versions Check network parameter Check fixture's ID Check fixture's LABEL Memory IC Angle Sensor Pan Sensor Pan Encoder Pan Drive IC Tilt Sensor Tilt Encoder Tilt Drive IC Temperature CMY_C Reset CMY_M Reset CMY_Y Reset COLOR Reset GOBO RESET RGOBO RESET ROTA. GOBO SERVICE FIXED GOBO PRISM 1 RESET PRISM 2 RESET FOCUS RESET PAN TILT CMY-C ±127 ±127 ±127 CMY-M ±127 CMY-Y ±127 COLOR ±127 **** ROTA.GOBO ±127 GOBO.ROTA ±127 FIXED GOBO ±127 PRISM 1 ±127 PRISM 2 ±127 FOCUS ±127 OTHER ±127 UPDATE SOFTWARE All passwords of this product are <UP>, <DOWN>,<UP>, <DOWN>, <ENTER> GOBO Reset RGOBO Reset FIXED GOBO reset PRISM 1 Reset PRISM 2 Reset FOCUS Reset Pan position fine adjustment Tilt position fine adjustment CMY-C position fine adjustment CMY-M position fine adjustment CMY-Y position fine adjustment Color position fine adjustment ROTA.GOBO position fine adjustment GOBO.ROTA position fine adjustment Gobo position fine adjustment Prism1 position fine adjustment Prism2 position fine adjustment Focus position fine adjustment UPDATE SOFTWARE 10 4 USING A DMX512 CONTROLLER 4.1 DMX CONTROL BASIC STANDARD Extend (19CH) (23CH) (27CH) Value Function 1 1 1 000-255 PAN 0-540° - 2 2 000-255 PAN FINE 2 3 3 000-255 TILT 0-270° - 4 4 000-255 TILT FINE 3 5 5 000-255 PT Speed 4 6 6 000-255 CYAN 5 7 7 000-255 MAGENTA 6 8 8 000-255 YELLOW COLOUR MACRO 000-010 No Function 11-20 L106 21-30 L194 31-40 L019 41-50 R08 51-60 L213 61-70 R80 71-80 L202 81-90 L328 7 9 9 91-100 R3314 101-110 L101 111-120 L768 121-128 No Function 129-147 CYAN 100% / MAGENTA UP/ YELLOW 0% 148-166 CYAN DOWN / MAGENTA 100% / YELLOW 0% 167-185 CYAN 0% / MAGENTA 100% / YELLOW UP 186-204 CYAN 0% / MAGENTA DOWN / YELLOW 100% 205-223 CYAN UP / MAGENTA 0% / YELLOW 100% 224-242 CYAN 100% /MAGENTA 0%/YELLOW DOWN 243-255 CYAN 100%/MAGENTA UP/YELLOW 0% 8 10 10 000-255 CMY SPEED(SPEED 100%->1) COLOR WHEEL 19+1 0-7 WHITE 8-10 COLOR 1 11-13 COLOR 2 14-16 COLOR 3 9 11 11 17-19 COLOR 4 20-22 COLOR 5 23-25 COLOR 6 26-28 COLOR 7 29-31 COLOR 8 11 32-34 COLOR 9 35-37 COLOR 10 38-40 COLOR 11 41-43 COLOR 12 44-46 COLOR 13 47-49 COLOR 14 50-52 COLOR 15 53-55 COLOR 16 56-58 COLOR 17 59-61 COLOR 18 62-64 COLOR 19 65-191 COLOR WHELL1 0-360° 192-222 COLOR WHELL1 RAINBOW EFFECT(SPEED 100%->1) 223-224 STOP 225-255 COLOR WHELL1 RAINBOW EFFECT(SPEED 1->100%) - - 12 000-255 COLOR WHEEL FINE ROTATING GOBO 6+1 000-010 ROTATING WHITE 011-019 ROTATING GOBO 1 020-028 ROTATING GOBO 2 029-037 ROTATING GOBO 3 038-046 ROTATING GOBO 4 047-055 ROTATING GOBO 5 056-064 ROTATING GOBO 6 065-073 ROTATING GOBO 1 SHAKE (SPEED 1 --> 100%) 10 12 13 074-082 ROTATING GOBO 2 SHAKE (SPEED 1 --> 100%) 083-091 ROTATING GOBO 3 SHAKE (SPEED 1 --> 100%) 092-100 ROTATING GOBO 4 SHAKE (SPEED 1 --> 100%) 101-109 ROTATING GOBO 5 SHAKE (SPEED 1 --> 100%) 110-118 ROTATING GOBO 6 SHAKE (SPEED 1 --> 100%) 119-127 WHITE 128-190 ROTATING GOBO FLOWING WATER EFFECT (SPEED 100 --> 1%) 191-192 STOP WATER EFFECT 193-255 ROTATING GOBO FLOWING WATER EFFECT (SPEED 1 --> 100%) - - 14 000-255 ROTATING GOBO FINE GOBO ROTATING 0-120 ROTATING GOBO ANGLE ADJUSTMENT (0 --> 360°) 121-125 STOP 126-165 ROTATING GOBO SHAKE (SPEED 1 --> 100%) 166-170 STOP 11 13 15 ROTATING GOBO POSITIVE ROTATION (SPEED 100% 171-210 --> 1) 211-215 STOP 216-255 ROTATING GOBO REVERSE ROTATION (SPEED 1 --> 100%) 12 - - 16 000-255 GOBO ROTATING FINE FIXED GOBO WHEEL 19+1 0-10 WHITE 11-13 FIXED GOBO 1 14-16 FIXED GOBO 2 17-19 FIXED GOBO 3 20-22 FIXED GOBO 4 23-25 FIXED GOBO 5 26-28 FIXED GOBO 6 29-31 FIXED GOBO 7 32-34 FIXED GOBO 8 35-37 FIXED GOBO 9 38-40 FIXED GOBO 10 41-43 FIXED GOBO 11 44-46 FIXED GOBO 12 47-49 FIXED GOBO 13 50-52 FIXED GOBO 14 53-55 FIXED GOBO 15 56-58 FIXED GOBO 16 59-61 FIXED GOBO 17 62-64 FIXED GOBO 18 65-67 FIXED GOBO 19 68-70 FIXED GOBO 1 SHAKE (SPEED 1 --> 100%) 71-73 FIXED GOBO 2 SHAKE (SPEED 1 --> 100%) 12 14 17 74-76 FIXED GOBO 3 SHAKE (SPEED 1 --> 100%) 77-79 FIXED GOBO 4 SHAKE (SPEED 1 --> 100%) 80-82 FIXED GOBO 5 SHAKE (SPEED 1 --> 100%) 83-85 FIXED GOBO 6 SHAKE (SPEED 1 --> 100%) 86-88 FIXED GOBO 7 SHAKE (SPEED 1 --> 100%) 89-91 FIXED GOBO 8 SHAKE (SPEED 1 --> 100%) 92-94 FIXED GOBO 9 SHAKE (SPEED 1 --> 100%) 95-97 FIXED GOBO 10 SHAKE (SPEED 1 --> 100%) 98-100 FIXED GOBO 11 SHAKE (SPEED 1 --> 100%) 101-103 FIXED GOBO 12 SHAKE (SPEED 1 --> 100%) 104-106 FIXED GOBO 13 SHAKE (SPEED 1 --> 100%) 107-109 FIXED GOBO 14 SHAKE (SPEED 1 --> 100%) 110-112 FIXED GOBO 15 SHAKE (SPEED 1 --> 100%) 113-115 FIXED GOBO 16 SHAKE (SPEED 1 --> 100%) 116-118 FIXED GOBO 17 SHAKE (SPEED 1 --> 100%) 119-121 FIXED GOBO 18 SHAKE (SPEED 1 --> 100%) 122-124 FIXED GOBO 19 SHAKE (SPEED 1 --> 100%) 125-127 WHITE 128-190 STATIC GOBO JUMPING WATER EFFECT (SPEED 100 --> 1%) 191-192 STOP WATER EFFECT 193-255 STATIC GOBO FLOWING WATER EFFECT (SPEED 1 --> 100%) 13 - - 18 000-255 FIXED GOBO WHEEL FINE PRISM 1 0-10 WHITE 11-145 PRISM INSERT AND ADJUST THE ANGLE (0 --> 360°) 146-150 STOP 13 15 19 PRISM INSERT AND POSITIVE ROTATION (SPEED 151-200 100% --> 1) 201-205 STOP ROTATION 206-255 PRISM INSERT AND REVERSE ROTATION (SPEED 1 --> 100%) PRISM 2 0-10 WHITE 11-145 PRISM INSERT AND ADJUST THE ANGLE (0 --> 360°) 146-150 STOP 14 16 20 PRISM INSERT AND POSITIVE ROTATION (SPEED 151-200 100% --> 1) 201-205 STOP ROTATION 206-255 PRISM INSERT AND REVERSE ROTATION (SPEED 1 --> 100%) FROST 0-10 WHITE 11-145 FROST INSERT AND ADJUST THE ANGLE (0 --> 360°) 146-150 STOP 15 17 21 FROST INSERT AND POSITIVE ROTATION (SPEED 151-200 100% --> 1) 201-205 STOP ROTATION 206-255 FROST INSERT AND REVERSE ROTATION (SPEED 1 --> 100%) 16 18 22 000-255 FOCUS - 19 23 000-255 FOCUS FINE 17 20 24 000-255 DIMMER - 21 25 000-255 DIMMER FINE STROBE 0-9 NO FUNCTION 10-99 STROBE FROM SLOW TO FAST 18 22 26 100-109 NO FUNCTION 110-179 LIGHTNING STROBE 180-189 NO FUNCTION 190-255 RANDOM STROBE CONTROLEXECUTE AFTER 3 SECONDS 0-10 NO FUNCTION 11-20 PAN/TILT BLACK ACTIVATED 21-30 PAN/TILT BLACK DEACTIVATED 19 23 27 31-40 PAN INVERT 41-50 TILT INVERT 51-60 PAN/TILT INVERT OFF 61-70 STUDIO 14 71-80 81-90 91-100 101-110 111-120 121-130 131-140 141-150 151-160 161-170 171-180 181-190 191-200 201-210 211-220 221-230 231-240 241-255 POWER LIVE DIMMER SPEED Halogen DIMMER SPEED LED DIMMER CURVE LINEAR DIMMER CURVE SQUARE LAW DIMMER CURVE INV. SQUARE LAW DIMMER CURVE S-CURVE 1200Hz 2400Hz 4000Hz 6000Hz 25000Hz ALL RESET XY RESET COLOR SYSTEM RESET GOBO SYSTEM RESET OTHER RESET 15