Arten Oy - Valaisimet ammattiasiakkaille
Instruction Manual for JUPE LED models including: JPL-ZGREC5-250VA, Smart Dimmer Module 250W, Dimmer Module 250W, Smart Module 250W, Module 250W
2). Inclusion to a Zigbeee Network 1). Factory Reset Min. Reset Indicator Max. Speed. Cx L L P 230V～50Hz 5-250W R,C Trailing Edge Trailing Edge Smart Dimmer
1).Turn off the power To prevent electrical shock and/or equipment damage, disconnect electrical power at the main fuse or circuit breaker before installation and maintenance. Be aware that even if the circuit breaker is off, some voltage may remain in the wires — before proceeding with the installation, be sure no voltage is present in the wiring.
File Info : application/pdf, 4 Pages, 2.22MB
DocumentDocumentJPL-ZGREC5-250VA Smart Dimmer Module 250W Min. Setting To set the minimum light level. Max. Setting To set the maximum light level. Dimming Speed. Setting To set dimming speed. LED Indicator Indicates resets and when the dimmer is in pairing mode Reset Button To set the dimmer to factory setting or to pair mode. Zigbee support Suitable for several home automation apps Voice support (Amazon Alexa & Google Assistant / Homey) Works with push-button (momentary switch) Optimal dimmable & light stability Suitable for 0-250W LED Saves and restores the last status after a power failure MIN and MAX light adjustment and dimming speed Suitable for 90% of all LEDs Does not require a neutral line, 3 wire connection available Soft start system Noiseless dimming 1. Specifications Input voltage Power (load) Suitable for Dimming method Working temperature Operation Dimensions Weight 230V ~ 50Hz 0-250W LED 10-250W Halogen light bulbs Led-, halogen-, incandescent bulbs R,C Phase cut 40 Push Dimming by Momentary Switch 45.1*45.1*19.8mm 35.4g 1 Jupeled Oy | info@jupeled.fi | www.jupeled.fi 2. Installation 1).Turn off the power To prevent electrical shock and/or equipment damage, disconnect electrical power at the main fuse or circuit breaker before installation and maintenance. Be aware that even if the circuit breaker is off, some voltage may remain in the wires -- before proceeding with the installation, be sure no voltage is present in the wiring. Take extra precautions to avoid accidentally turning the device on during installation. 2). Connect the device exactly according to the diagrams shown below This dimmer is available for 2wire and 3-wire system. please note if it is 2wire, N and Load port must be connected to make stable dimming. 3). Turn the power back Min. Max. Reset Indicator Speed. JPL-ZGREC5-250VA Trailing Edge Smart Dimmer 230Vj50Hz 5-250W Cx R,C Trailing Edge LLP Min. Max. Indicator Reset Speed. JPL-ZGREC5-250VA Trailing Edge Smart Dimmer 230Vj50Hz 5-250W Cx R,C Trailing Edge LLP Not suitable for 2way switch, must be push/ Momentary switch N N L L 3. Operation 1) Min./Max./Dimming Speed adjustment For the SMART dimmer to work optimally or suitable for your preference, you can adjust the brightness at the Min. and Max. level and also the dimming speed with the MIN./MAX./Dimming Speed adjustment. MIN adjustment : Switch on the lights. When the lights are on, insert a screwdriver in MIN and turn to the left. When the light becomes unsteady, turn slightly back to the right so that the light remains steady. MAX adjustment : Switch on the lights. When the lights are on, insert a screwdriver in MAX and turn to the right. When the light becomes unsteady, turn slightly back to the left so that the light remains steady. Dimming Speed adjustment: Insert a screwdriver in Speed, clockwise to increase the dimming speed when you push the momentary switch, vice versa. 4. Zigbee Cluster 1) Input Cluster - 0x0000: Basic - 0x0003: Identify - 0x0004: Groups - 0x0005: Scenes - 0x0006: On/off - 0x0008: Level Control - 0x0b05: Diagnostics 2) Output Cluster - 0x0019: OTA 2 Jupeled Oy | info@jupeled.fi | www.jupeled.fi 5. Zigbee Setting 1). Factory Reset Step 2.When the Indicator stay in Red for 10s, reset finished. Min. Max. Reset Indicator Speed. JPL-ZGREC5-250VA Trailing Edge Smart Dimmer 230Vj50Hz 5-250W Cx R,C Trailing Edge LLP Step 1.Press the reset button for 5s. Please Note: This procedure should only be used when the primary controller is inoperable or otherwise missing. Reset Dimmer controller to factory default settings will sets the Dimmer to not in Z-Wave network state, delete the Association setting and restore the Configuration setting to the default. The Dimmer controller will start SmartStart Inclusion when it is reset. 2). Inclusion to a Zigbeee Network Step 1. Remove the device from previous Zigbee network if it has already been added to, otherwise pairing mode will be fail. Step 3.The indicator will start blinking blue and stay solid for 10s when pairing succeed, timeout 15mins. Min. Max. Indicator Reset Speed. JPL-ZGREC5-250VA Trailing Edge Smart Dimmer 230Vj50Hz 5-250W Cx R,C Trailing Edge LLP Step 2.Double Press the reset button. 3). Remove from a Zigbee Network Method 1. From your Zigbee hub interface, choose to delete or reset the device as instructed. Method 2. Remove from the Device, see below instructions. Step 2. The indicator will start blinking purple and stay solid for 10s when remove done, timeout 3mins. Min. Max. Indicator Reset Speed. JPL-ZGREC5-250VA Trailing Edge Smart Dimmer 230Vj50Hz 5-250W Cx R,C Trailing Edge LLP Step 1.Press the reset button for 3 times. 3 Jupeled Oy | info@jupeled.fi | www.jupeled.fi 4). TouchLink Step 2. The indicator will start blinking green and stay solid for 10s when pairing succeed, timeout 15mins. Step 3. Bring the remote within 10cm of the smart dimmer and set the remote into TouchLink commissioning. Min. Max. Indicator Reset Speed. JPL-ZGREC5-250VA Trailing Edge Smart Dimmer 230Vj50Hz 5-250W Cx R,C Trailing Edge LLP Step 1. Press the reset button for 4 times. Step 4. The Light will blinking 10 times when TouchLink Succeed. Note: a. When both devices (Dimmer and remote) not included in the Zigbee Network, each dimmer can link with one remote max. b. When both devices are included in the same Zigbee network, each dimmer can link with max 30 remotes. c. For Philips Hue Hubs and Amazon Echo Plus, add remote and device to network first then touchlink. 5) Find and Bind Note: Make sure the device and remote already added to the same Zigbee network Step 2. The indicator will start blinking yellow and stay solid for 10s. Step 3. Set the remote into find and bind mode and enable it to find and bind commissioning. Please refer to the manufacturers instructions of how. Step 4. There shall be an indication on the remote that it binds the device successfully and can control it. Min. Max. Indicator Reset Speed. JPL-ZGREC5-250VA Trailing Edge Smart Dimmer 230Vj50Hz 5-250W Cx R,C Trailing Edge LLP Step 1. Press the reset button for 5 times. 3 Jupeled Oy | info@jupeled.fi | www.jupeled.fi