Package List
The following components are included in the package:
- (A) Casters: Quantity: 5
- (B) Star Base: Quantity: 1
- (C) Gas Lift: Quantity: 1
- (D) Left Plastic Cover Set: Quantity: 1
- (E) Right Plastic Cover Set: Quantity: 1
- (F) Angle Adjusters: Quantity: 2 (Left and Right)
- (G) Seat Plate: Quantity: 1
- (H) Seat Cushion: Quantity: 1
- (I) Back Cushion: Quantity: 1
- (J) Armrests: Quantity: 2 (Left and Right)
- (1) Bolts M5x10mm: Quantity: 6
- (2) Bolts M6x10mm: Quantity: 10
- (3) Bolts M8x25mm: Quantity: 16
- (4) Cable: Quantity: 1
- (5) Wrench: Quantity: 1
- (6) Wrench: Quantity: 1
Assembly Instructions
Step 1: Attach Casters to Star Base
Turn the Star Base (B) upside down. Press the Casters (A) into the holes at the end of each base leg until they are securely fitted.
Step 2: Install Gas Lift
Turn the Star Base (B) upright. Insert the Gas Lift (C) into the center hole of the Star Base.
Step 3: Prepare Seat and Back
Remove all M8x25mm Bolts (3) from the seat cushion (H) and back cushion (I).
Step 4: Attach Seat Plate to Seat Cushion
Align the Seat Plate (G) to the bottom of the Seat Cushion (H). Ensure the front of the Seat Plate is facing the front of the Seat Cushion. Attach the Seat Plate to the Seat Cushion using four M8x25mm bolts (3). Tighten all bolts with the wrench (6).
Step 5: Secure Seat Plate
Align the Seat Plate (G) to the bottom of the Seat Cushion (H). Ensure the front of the Seat Plate is facing the front of the Seat Cushion. Attach the Seat Plate to the Seat Cushion using four M8x25mm bolts (3). Tighten all bolts with the wrench (6).
Step 6: Mount Seat Cushion to Gas Lift
Turn the Seat Cushion (H) upright. Align the center hole of the Seat Plate (G) over the Gas Lift (C). Push the Seat Cushion down onto the Gas Lift firmly until the connection is secure.
Step 7: Attach Angle Adjusters to Seat Cushion
Using the Angle Adjusters (F), align them over the pre-drilled holes underneath the Seat Cushion (H). Attach using M8x25mm bolts (3) and tighten with the wrench (6). Note: Tighten bolts to 50% initially.
Step 8: Attach Back Cushion
Align the Angle Adjusters (F) over the pre-drilled holes underneath the Back Cushion (I). Attach using M8x25mm bolts (3) and tighten with the wrench (6).
Step 9: Final Tightening
Adjust the balance of the full chair. Then, tighten all bolts to 100% on each side of the adjuster.
Step 10: Install Plastic Covers
Attach the Plastic Covers (D, E) to the right and left sides using four M5x8mm bolts (1) and the wrench (5).
Congratulations
You have successfully assembled your Kasorix chair.
If you encounter any problems during installation or have other issues, please contact Kasorixchair-service@outlook.com. A reply will be provided within 24 hours.
Instructions for Use
1. Seat Height Adjustment
Use the paddle-shaped lever on the right side:
- To raise the seat: While taking your weight off the chair, lift the lever up.
- To lower the seat: While seated, lift the lever up.
Note: At the proper height, your feet should rest flat on the floor.
2. Tilt Tension Adjustment
Locate the long stem with a knob under the seat cushion:
- To increase tension: While seated, turn the knob forward (towards the '+' sign).
- To decrease tension: While seated, turn the knob backward (towards the '-' sign).
Note: Set the tilt tension to control the resistance you feel when leaning back.
3. Operating the Tilt Lockout
- To allow the chair to tilt back: Pull the control handle out.
- To stop the chair from tilting: Sit forward, then push the control handle in.
Note: At the proper height, your feet should rest flat on the floor.
4. 2D-Function Armrest
The armrests can be adjusted:
- (1) Up and Down.
- (2) Left and Right.
5. Backrest Recline
Pull the lever fully and lean back slowly until the desired angle is achieved. Slowly return the lever to its starting position, ensuring it locks back in place.
6. Footrest Operation
Pull out the pole of the footrest and turn the footrest to the front.
Safety and Maintenance
- Do not stand on the chair; do not use the chair as a stepladder.
- Use this product for seating one person at a time.
- Ensure all bolts and screws are firmly secured before use.
- Avoid contact with sharp objects to prevent puncturing the fabric.
- Every 6 months, check all bolts and screws to ensure they are tight.
- To clean, spot clean only using a damp towel and mild cleaner. Test on a small, obscure area of fabric first.
- Chair weight limit: not to exceed 300 lbs.
Safety Information:
Limited Warranty
Kasorix promises to repair or replace any chair found to be defective in material or workmanship within one (1) year from the date of original purchase, provided you, the original purchaser, still own it. This is your sole and exclusive remedy.
Exclusions:
- Normal wear and tear, which are to be expected over the course of ownership.
- Misuse, abuse, or excessive use of the product.
- Modifications or attachments to the product that are not approved by Kasorix.
- Products that were not installed, used, or maintained in accordance with product instructions and warnings.
- Products used for rental or commercial purposes.
- Damage caused by the carrier in-transit is handled under separate terms.
Seating Usage: Normal use for seating is identified as the equivalent of a single shift, forty- (40) hour workweek. To the extent that a seating product is used in a manner exceeding this, the applicable warranty period will be reduced in a pro-rata manner.
Some retailers might have custom models imported direct from the factory and therefore are not supported by our local service team because we don't have the correct parts. Please contact your retailer directly for support. If you have any questions, please contact us, and we will be happy to assist and identify those items.
Return Policy:
Kasorix adopts a 30-day return policy. All products purchased may be returned within this timeframe. You need to contact us within 30 days after the product(s) came into your possession, and the product(s) must be returned without any undue delays.
How Returns Work:
Contact us through the contact form on our website and attach the invoice as proof of purchase. Please also write the reason for return. We will then get back to you as soon as possible with information on where to send the product(s). As soon as we have received the product(s) and made an inspection, we will inform you of our decision. If a refund is approved, it will be automatically credited to your credit card or original method of payment. If the product(s) is damaged, not in its original condition, or missing parts, we will inform you if you are eligible for a partial refund. This is decided on a case-by-case basis depending on the severity of the damages or missing parts.
Models: 8509 Gaming Chair, Gaming ChairFile Info : application/pdf, 14 Pages, 6.82MB
DocumentDocument