4PCS Conversation Set User Manual
Introduction
This user's manual provides important safety information and assembly instructions for your 4PCS Conversation Set. Please read and keep for future reference.
Before You Start
⚠ Important Safety Information:
- Read each step carefully before starting. It is very important to ensure each step is followed in correct order, otherwise assembly difficulties may occur.
- Most board parts are labeled or stamped on the raw edges. Have a check to make sure all parts are included.
- Work in a spacious area, preferably on a carpet close to where the unit will be used.
- Keep the handtools close at hand. Do not use power tools to assemble your furniture. They may scratch or damage the parts.
Part List
- 1 Backrest Panel (Double) - 1 pc
- 2 Left Leg Panel - 3 pcs
- 3 Right Leg Panel - 3 pcs
- 4 Seat Panel (Double) - 1 pc
- 5 Front-Leg Panel (Double) - 1 pc
- 6 Backrest Panel (Single) - 2 pcs
- 7 Seat Panel (Single) - 2 pcs
- 8 Front-Leg Panel (Single) - 2 pcs
- 9 Short Table Side - 2 pcs
- 10 Long Table Side - 2 pcs
- 11 Table Top - 1 pc
- 12 Glass Top - 1 pc
- 13 Cushion Seat - 4 pcs
- 14 Cushion Back - 4 pcs
- 15 Plastic Leg - 16 pcs
Hardware
- A M6x25mm Bolt - 32 pcs
- B M6x30mm Bolt - 62 pcs
- C M4 Allen Key - 2 pcs
Assembly Instructions
Step 1: Assemble Chair Side Frames (x3)
Assemble three identical chair side frames. Each frame consists of one backrest panel (likely Part 6), one left leg panel (Part 2), and one right leg panel (Part 3). Secure each leg panel to the backrest panel using three Bolt A. This step uses a total of 18 Bolt A. [Warning: 50% Tightness, 100% Tightness, Rotate, Cross]
Step 2: Assemble Single Chair Seat Base (x2)
For two of the assembled side frames from Step 1, attach the Seat Panel (Part 7) to the lower section using two Bolt B. [Warning: 50% Tightness, 100% Tightness, Rotate, Cross]
Step 3: Attach Front-Leg Panel to Single Chair Frame (x2)
Attach the Front-Leg Panel (Part 8) to the front of the two single chair frames assembled in Step 2, using two Bolt B for each. [Warning: 50% Tightness, 100% Tightness, Rotate, Cross]
Step 4: Assemble Second Set of Single Chair Seat Bases (x2)
For the remaining two assembled side frames from Step 1, attach the Seat Panel (Part 7) using two Bolt B for each. [Warning: 50% Tightness, 100% Tightness, Rotate, Cross]
Step 5: Attach Front-Leg Panels to Second Set of Single Chair Frames (x2)
Attach the Front-Leg Panel (Part 8) to the front of the two single chair frames assembled in Step 4, using two Bolt B for each. [Warning: 50% Tightness, 100% Tightness, Rotate, Cross]
Step 6: Completed Single Chairs (x2)
Two completed single chairs are now assembled. [100% Tightness, Rotate]
Step 7: Assemble Double Chair Backrest (x1)
Assemble the double chair frame. Attach the Backrest Panel (Double) (Part 1) to the main frame structure, using four Bolt B. [Warning: 50% Tightness, 100% Tightness, Rotate, Cross]
Step 8: Assemble Double Chair Front-Leg Panel (x1)
Attach the Front-Leg Panel (Double) (Part 5) to the front of the double chair frame, using two Bolt B. [Warning: 50% Tightness, 100% Tightness, Rotate, Cross]
Step 9: Assemble Table Base Structure (x1)
Begin assembling the table base. Connect the Short Table Sides (Part 9) and Long Table Sides (Part 10) using Bolt B. The diagram indicates multiple connections. [Warning: 50% Tightness, 100% Tightness, Rotate, Cross]
Step 10: Attach Table Sides (x2)
Continue assembling the table base by attaching the remaining Short Table Sides (Part 9) and Long Table Sides (Part 10) to the structure using Bolt B. [Warning: 50% Tightness, 100% Tightness, Rotate, Cross]
Step 11: Attach Table Top to Base (x1)
Attach the Table Top (Part 11) to the assembled table base using four Bolt B. [Warning: 50% Tightness, 100% Tightness, Rotate, Cross]
Step 12: Completed Table Frame (x1)
The main table frame is now assembled. [100% Tightness, Rotate]
Step 13: Attach Table Top to Base (x1)
Attach the Table Top (Part 11) to the assembled table base using four Bolt B. [Warning: 50% Tightness, 100% Tightness, Rotate, Cross]
Step 14: Attach Table Sides (x2)
Attach the Short Table Sides (Part 9) to the table base structure using four Bolt B. [Warning: 50% Tightness, 100% Tightness, Rotate, Cross]
Step 15: Attach Plastic Legs to Table (x16)
Attach the Plastic Legs (Part 15) to the bottom of the table base using four Bolt A per leg. This step uses a total of 16 Bolt A. [Warning: 50% Tightness, 100% Tightness, Rotate, Cross]
Step 16: Place Glass Top on Table (x1)
Place the Glass Top (Part 12) onto the assembled table top (Part 11). [100% Tightness, Rotate]
Step 17: Completed Table (x1)
The table is now fully assembled.
Step 18: Add Cushions to Chairs (x4 sets)
Place the Cushion Seats (Part 13) and Cushion Backs (Part 14) onto the assembled single and double chairs.
Step 19: Finished Product
The 4PCS Conversation Set is now fully assembled and ready for use.
Care and Maintenance
Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage the finish. Never use water to clean your furniture as it may cause damage to the finish.
Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid rubbing.
Check bolts/screws periodically and tighten them if necessary.
Further advice about wood furniture care
Please protect your outdoor furniture with a cover when not in use since long-term sunlight exposure will result in damage to the surface. In addition to sunlight damage, wood and metal frames suffer when exposed to extremes in temperature and humidity. Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful tips will enhance your furniture as it ages.