manuals.plus
TCL
TTE Technology Inc. 65S423 LED TV FCC Test Report and Technical Specifications
Test Report for TCL models including: TTE Technology Inc., TCL, 65S423, 65S421, 65S4, 65S425, 65S427, 65S425-MX, 65S427-MX, 65S425-CA, 65S427-CA, W8U65S423, JBP_B, LED TV, Computer Peripheral
Date of Type Enid X546 Test Report TTE Technology, Inc. 65S423 LED TV W8U65S423 W8U65S423 65s423
GetApplicationAttachment.html?id=4223363 TTE Technology, Inc.
TEST REPORT
SCOPE OF WORK FCC TESTING65S423, 65S421, 65S4, 65S425, 65S427, 65S425-MX, 65S427-MX, 65S425-CA, 65S427-CA, 65S4followed by one character; may be followed by MX or -CA.
REPORT NUMBER 190228019SZN-001
ISSUE DATE
[REVISED DATE]
15 March 2019
[---------------------]
PAGES 37
DOCUMENT CONTROL NUMBER FCC ID JBP_B © 2017 INTERTEK
Test Report
Intertek Report No.: 190228019SZN-001
TTE Technology, Inc.
Application For
Certification FCC ID: W8U65S423
LED TV
Model: 65S423 Additional Models: 65S421, 65S4, 65S425, 65S427, 65S425-MX, 65S427-MX, 65S425-CA, 65S427-CA, 65S4followed by one character;
may be followed by -MX or -CA.
Brand Name: TCL
Computer Peripheral
Report No.: 190228019SZN-001
Prepared and Checked by:
Approved by:
Ryan Chen Engineer
Kidd Yang Technical Supervisor Date: 15 March 2019
This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program.
Intertek Testing Service Shenzhen Ltd. Longhua Branch
101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, Shenzhen, P.R. China. Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751
Version: 01-November-2017
Page: 1 of 37
FCC ID JBP_B
Test Report
Intertek Report No.: 190228019SZN-001
LIST OF EXHIBITS
INTRODUCTION EXHIBIT 1: EXHIBIT 2: EXHIBIT 3: EXHIBIT 4: EXHIBIT 5: EXHIBIT 6: EXHIBIT 7: EXHIBIT 8: EXHIBIT 9:
General Description System Test Configuration Emission Results Equipment Photographs Product Labeling Technical Specifications Instruction Manual Miscellaneous Information Test Equipment List
Version: 01-November-2017
Page: 2 of 37
FCC ID JBP_B
Test Report
Intertek Report No.: 190228019SZN-001
MEASUREMENT / TECHNICAL REPORT
TTE Technology, Inc.
MODEL: 65S423
Additional Models: 65S421, 65S4, 65S425, 65S427, 65S425-MX, 65S427-MX, 65S425-CA, 65S427-CA, 65S4followed by one character; may be followed by -MX or
-CA.
FCC ID: W8U65S423
This report concerns (check one:)
Original Grant X Class I Change
Equipment Type: JBP-Class B Computing Device Peripheral
Deferred grant requested per 47 CFR 0.457(d)(1)(ii)?
Yes
No X
If yes, defer until: date
Company Name agrees to notify the Commission by: date
of the intended date of announcement of the product so that the grant can be issued on that date.
Transition Rules Request per 15.37?
Yes
No X
If no, assumed Part 15, Subpart B for unintentional radiator - the new 47 CFR [10-01-17 Edition] provision.
Report prepared by:
Ryan Chen Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, Shenzhen, P.R. China Phone: 86-755-8614 0682 Fax: 86-755-8601 6751
Version: 01-November-2017
Page: 3 of 37
FCC ID JBP_B
Test Report
Intertek Report No.: 190228019SZN-001
Table of Contents
1.0 General Description.............................................................................................. 7 1.1 Product Description........................................................................................ 7 1.2 Related Submittal(s) Grants ........................................................................... 7 1.3 Test Methodology........................................................................................... 8 1.4 Test Facility .................................................................................................... 8
2.0 System Test Configuration ................................................................................ 10 2.1 Justification .................................................................................................. 10 2.2 EUT Exercising Software ............................................................................. 10 2.3 Special Accessories ..................................................................................... 10 2.4 Equipment Modification ................................................................................ 10 2.5 Measurement Uncertainty ............................................................................ 11 2.6 Support Equipment List and Description ...................................................... 11
3.0 Emission Results................................................................................................ 13 3.1 Field Strength Calculation ............................................................................ 14 3.2 Field Strength Calculation (cont'd) ............................................................... 15 3.3 Radiated Emission Configuration Photograph ............................................. 16 3.4 Radiated Emission Data............................................................................... 17 3.5 Conducted Emission at Mains Terminal ....................................................... 20 3.6 Conducted Emission Data............................................................................ 21
4.0 Equipment Photographs .................................................................................... 25 5.0 Product Labelling ............................................................................................... 27 6.0 Technical Specifications .................................................................................... 29 7.0 Instruction Manual.............................................................................................. 31 8.0 Miscellaneous Information ................................................................................ 33
8.1 Emissions Test Procedures ......................................................................... 34 8.2 Emissions Test Procedures (cont'd)............................................................. 35 9.0 Technical Specifications .................................................................................... 37
Version: 01-November-2017
Page: 4 of 37
FCC ID JBP_B
Test Report
Intertek Report No.: 190228019SZN-001
List of attached files
Exhibit Type Test Report Test Setup Photo Test Setup Photo External Photo Internal Photo Block Diagram ID Label / Location User Manual Cover Letter Cover Letter
File Description Test Report Radiated photos Conducted photos External Photos Internal Photos Block Diagram Label Artwork and Location User Manual Confidential Letter Letter of Agency
Filename report.pdf radiated photos.pdf conducted photos.pdf external photos.pdf internal photos.pdf block.pdf label.pdf manual.pdf request.pdf agency.pdf
Version: 01-November-2017
Page: 5 of 37
FCC ID JBP_B
Test Report
Intertek Report No.: 190228019SZN-001
EXHIBIT 1 GENERAL DESCRIPTION
Version: 01-November-2017
Page: 6 of 37
FCC ID JBP_B
Test Report
1.0 General Description
Intertek Report No.: 190228019SZN-001
1.1 Product Description
The Equipment Under Test (EUT) is a LED TV. The device can be used to connect PC by HDMI port. The EUT is powered by AC 120V, 60Hz.
The EUT contains a module which can be operated in the frequency band of 2412MHz to 2462MHz in 802.11b, 802.11g and 802.11n-HT20 modes, 2422MHz to 2452MHz in 802.11n-HT40 mode, and 5180MHz to 5240MHz, 5745MHz to 5825MHz in 802.11a, 802.11n (20MHz, 40MHz) and 11ac (80MHz) modes.
The Model: 65S421, 65S4, 65S425, 65S427, 65S425-MX, 65S427-MX, 65S425-CA, 65S427-CA, 65S4followed by one character; may be followed by -MX or -CA. are the same as the Model: 65S423 in hardware aspect. The models are difference in packaging and marketing purpose only.
1.2 Related Submittal(s) Grants
This is an application for certification of a computer peripheral. Other digital functions were reported in the verification report: 190228019SZN-002.
The host contains a WIFI module, which has been granted under the FCC ID: 2AC23-WC1KR2601.
Version: 01-November-2017
Page: 7 of 37
FCC ID JBP_B
Test Report
1.3 Test Methodology
Intertek Report No.: 190228019SZN-001
Both AC mains line-conducted and radiated emission measurements were performed according to the procedures in ANSI C63.4 (2014). Radiated emission measurement was performed in Semi-anechoic chamber and conducted emission measurement was performed in shield room. For radiated emission measurement, preliminary scans were performed in the semianechoic chamber only to determine the worst-case modes. All radiated tests were performed at an antenna to EUT distance of 3 meters, unless stated otherwise in the "Justification Section" of this Application.
1.4 Test Facility
The Semi-anechoic chamber and shielding room used to collect the radiated data and conducted data are Intertek Testing Services Shenzhen Ltd. Longhua Branch and located at 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen, P.R. China. This test facility and site measurement data have been fully placed on file with the FCC (Registration Number: CN1188).
Version: 01-November-2017
Page: 8 of 37
FCC ID JBP_B
Test Report
Intertek Report No.: 190228019SZN-001
EXHIBIT 2 SYSTEM TEST CONFIGURATION
Version: 01-November-2017
Page: 9 of 37
FCC ID JBP_B
Test Report
2.0 System Test Configuration
Intertek Report No.: 190228019SZN-001
2.1 Justification
The system was configured for testing in a typical fashion (as a customer would normally use it), and in the confines as outlined in ANSI C63.4 (2014).
The device was powered by AC 120V/60Hz during the test. The host device contains a Wi-Fi module which was installed and operating during the test, and only the worst-case data was reported in this report.
For maximizing emissions, the EUT was rotated through 360°, the antenna height was varied from 1 meter to 4 meters above the ground plane, and the antenna polarization was changed. The step by step procedure for maximizing emissions led to the data reported in Exhibit 3.0.
The rear of unit shall be flushed with the rear of the table.
The equipment under test (EUT) was configured for testing in a typical fashion (as a customer would normally use it). The EUT was placed on turn table, which enabled the engineer to maximize emissions through its placement in the three orthogonal axes.
The frequency ranges from 30MHz to 29.25GHz was searched for spurious emissions from the device. Only those emissions reported were detected. All other emissions were at least 20 dB below the applicable limits.
2.2 EUT Exercising Software
N/A
2.3 Special Accessories
N/A
2.4 Equipment Modification
Any modifications installed previous to testing by TTE Technology, Inc. will be incorporated in each production model sold / leased in the United States.
No modifications were installed by Intertek Testing Services Shenzhen Ltd. Longhua Branch.
Version: 01-November-2017
Page: 10 of 37
FCC ID JBP_B
Test Report
Intertek Report No.: 190228019SZN-001
2.5 Measurement Uncertainty
When determining the test conclusion, the Measurement Uncertainty of test has been considered.
2.6 Support Equipment List and Description This product was tested in the following configuration: Refer List:
Description Laptop
Hard Disk USB Cable USB Memory Dummy Load HDMI Cable*3 AV Cable AV Cable Adapter Tuner Resister Remote Controller Headphone Coaxial Cable RJ45 Cable Optical Cable
Manufacturer DELL
Smart.drive Smart.drive
SanDisk N/A N/A N/A N/A N/A TCL Sony N/A N/A N/A
Model No. Latitude 3480
HD-003 Unshielded, Length 155cm
SDCZ36-002G-P36 N/A
UnShielded, Length 180cm Unshielded, Length 120cm Unshielded, Length 15cm
75ohm N/A
Unshielded, Length 110cm Shielded, Length 500cm Shielded, Length 450cm
Unshielded, Length 130cm
Version: 01-November-2017
Page: 11 of 37
FCC ID JBP_B
Test Report
Intertek Report No.: 190228019SZN-001
EXHIBIT 3 EMISSION RESULTS
Version: 01-November-2017
Page: 12 of 37
FCC ID JBP_B
Test Report
3.0 Emission Results
Intertek Report No.: 190228019SZN-001
Data is included worst case configuration (the configuration which resulted in the highest emission levels). A sample calculation, configuration photographs and data tables of the emissions are included.
Version: 01-November-2017
Page: 13 of 37
FCC ID JBP_B
Test Report
3.1 Field Strength Calculation
Intertek Report No.: 190228019SZN-001
The field strength is calculated by adding the reading on the Spectrum Analyzer to the factors associated with preamplifiers (if any), antennas, cables, pulse desensitization and average factors (when specified limit is in average and measurements are made with peak detectors). A sample calculation is included below.
FS = RA + AF + CF - AG
where FS = Field Strength in dBV/m RA = Receiver Amplitude (including preamplifier) in dBV CF = Cable Attenuation Factor in dB AF = Antenna Factor in dB/m AG = Amplifier Gain in dB
In the radiated emission table which follows, the reading shown on the data table may reflect the preamplifier gain. An example of the calculations, where the reading does not reflect the preamplifier gain, follows:
FS = RA + AF + CF - AG
Version: 01-November-2017
Page: 14 of 37
FCC ID JBP_B
Test Report
3.2 Field Strength Calculation (cont'd)
Intertek Report No.: 190228019SZN-001
Example
Assume a receiver reading of 62.0dBV is obtained. The antenna factor of 7.4dB/m and cable factor of 1.6dB is added. The amplifier gain of 29dB is subtracted. The net field strength for comparison to the appropriate emission limit is 42dBV/m. This value in dBV/m was converted to its corresponding level in V/m.
RA = 62.0dBV AF = 7.4dB/m CF = 1.6dB AG = 29.0dB
FS = 62 + 7.4 + 1.6 - 29 = 42dBV/m Level in V/m = Common Antilogarithm [(42dBV/m)/20] = 125.9V/m
Version: 01-November-2017
Page: 15 of 37
FCC ID JBP_B
Test Report
Intertek Report No.: 190228019SZN-001
3.3 Radiated Emission Configuration Photograph
Worst Case Radiated Emission At
890.1MHz (HDMI In(4K) Mode)
For electronic filing, the worst case radiated emission configuration photograph is saved with filename: radiated photos.pdf.
Version: 01-November-2017
Page: 16 of 37
FCC ID JBP_B
Test Report
3.4 Radiated Emission Data
Intertek Report No.: 190228019SZN-001
The data on the following page lists the significant emission frequencies, the limit and the margin of compliance. Numbers with a minus sign are below the limit.
Judgement: Passed by 4.1dB margin (HDMI In(4K) Mode)
TEST PERSONNEL: Sign on file Ryan Chen, Engineer Typed/Printed Name
07 March 2019 Date
Version: 01-November-2017
Page: 17 of 37
FCC ID JBP_B
Test Report
Applicant: TTE Technology, Inc. Date of Test: 07 March 2019 Worst Case Operating Mode:
Intertek Report No.: 190228019SZN-001
Model: 65S423 HDMI In(4K)
Table 1
Below 1GHz Polarization Frequency (MHz)
Horizontal Horizontal Horizontal
Vertical Vertical Vertical
148.3 296.8 890.1 33.4 148.3 890.1
Radiated Emissions
Reading (dBµV)
49.9 42.2 38.1 32.6 48.7 38.0
PreAmp Gain (dB) 20.0 20.0 20.0 20.0 20.0 20.0
Antenna Factor (dB)
9.4 13.9 23.9 19.8 9.4 23.9
Net at 3m (dBµV/m)
39.3 36.1 42.0 32.4 38.1 41.9
Limit at 3m (dBµV/m)
43.5 46.0 46.0 40.0 43.5 46.0
Margin (dB)
-4.2 -9.9 -4.0 -7.6 -5.4 -4.1
Above 1GHz Polarization Frequency Reading
(MHz) (dBµV)
Horizontal 1186.9 57.7 Horizontal 1590.8 60.0 Horizontal 3210.7 62.5 Horizontal 1186.9 52.4 Horizontal 1590.8 42.5 Horizontal 3270.7 54.8
Vertical 1186.9 57.8 Vertical 1642.6 61.6 Vertical 3213.8 65.0 Vertical 1186.9 52.1 Vertical 1642.6 49.5 Vertical 3213.8 44.9
PreAmp Gain (dB) 36.6 36.3 36.4 36.6 36.3 36.4 36.3 36.5 36.4 36.3 36.5
36.4
Antenna Net
Limit Margin Detector
Factor at 3m at 3m (dB)
(dB) (dBµV/m) (dBµV/m)
22.9 44.0 74.0 -30.0 PK
24.7 48.4 74.0 -25.6 PK
29.1 55.2 74.0 -18.8 PK
22.9 38.7 54.0 -15.3 AV
24.7 30.9 54.0 -23.1 AV
29.1 47.5 54.0 -6.5
AV
22.8 44.3 74.0 -29.7 PK
24.8 49.9 74.0 -24.1 PK
29.0 57.6 74.0 -16.4 PK
22.8 38.6 54.0 -15.4 AV
24.8 37.8 54.0 -16.2 AV
29.0 37.5 54.0 -16.5 AV
Version: 01-November-2017
Page: 18 of 37
FCC ID JBP_B
Test Report
NOTES: 1.
Intertek Report No.: 190228019SZN-001
Quasi-Peak detector is used for frequency up to 1GHz, Peak detector and Average detector are used for frequency from 1GHz to 29.25GHz.
2. All measurements were made at 3 meters.
3. Negative value in the margin column shows emission below limit.
4. All other emissions were at least 20 dB below the applicable limits.
Test Engineer: Ryan Chen
Version: 01-November-2017
Page: 19 of 37
FCC ID JBP_B
Test Report
Intertek Report No.: 190228019SZN-001
3.5 Conducted Emission at Mains Terminal
3.5.1 Conducted Emission Configuration Photograph
Worst Case Conducted Configuration at
0.154 MHz (HDMI In Mode)
For electronic filing, the worst case conducted emission configuration photograph is saved with filename: conducted photos.pdf.
Version: 01-November-2017
Page: 20 of 37
FCC ID JBP_B
Test Report
3.6 Conducted Emission Data
Intertek Report No.: 190228019SZN-001
Judgement: Passed by 12.5 dB margin(HDMI In Mode)
TEST PERSONNEL: Sign on file Ryan Chen, Engineer Typed/Printed Name
08 March 2019 Date
Version: 01-November-2017
Page: 21 of 37
FCC ID JBP_B
Test Report
Company: TTE Technology, Inc. Date of Test: 08 March 2019 Model: 65S423 Operating Mode: HDMI IN Phase: Live
Conducted Emission Test - FCC
Intertek Report No.: 190228019SZN-001
Result Table QP
Frequency QuasiPeak Line
(MHz)
(dBV)
0.154000
52.2
L
0.206000
47.3
L
0.310000
43.2
L
0.466000
40.6
L
0.618000
40.6
L
0.926000
39.3
L
Corr. (dB)
9.6 9.6 9.6 9.6 9.7 9.7
Margin (dB)
13.6 16.1 16.8 16.0 15.4 16.7
Limit (dBV)
65.8 63.4 60.0 56.6 56.0 56.0
Result Table AV
Frequency Average Line
(MHz)
(dBV)
0.154000
43.3
L
0.206000
35.7
L
0.310000
32.4
L
0.466000
27.0
L
0.618000
27.7
L
0.926000
25.4
L
Corr. (dB)
9.6 9.6 9.6 9.6 9.7 9.7
Margin (dB)
12.5 17.7 17.6 19.6 18.3 20.6
Limit (dBV)
55.8 53.4 50.0 46.6 46.0 46.0
Test Engineer: Ryan Chen
Version: 01-November-2017
Page: 22 of 37
FCC ID JBP_B
Test Report
Company: TTE Technology, Inc. Date of Test: 08 March 2019 Model: 65S423 Operating Mode: HDMI In Phase: Neutral
Conducted Emission Test - FCC
Intertek Report No.: 190228019SZN-001
Result Table QP
Frequency QuasiPeak Line
(MHz)
(dBV)
0.154000
48.5
N
0.202000
46.6
N
0.310000
43.4
N
0.498000
36.8
N
0.778000
35.8
N
1.078000
34.8
N
Corr. (dB)
9.6 9.6 9.6 9.7 9.7 9.7
Margin (dB)
17.3 16.9 16.6 19.2 20.2 21.2
Limit (dBV)
65.8 63.5 60.0 56.0 56.0 56.0
Result Table AV
Frequency Average Line
(MHz)
(dBV)
0.154000
40.3
N
0.202000
35.3
N
0.310000
33.8
N
0.498000
24.8
N
0.778000
20.3
N
1.078000
19.8
N
Corr. (dB)
9.6 9.6 9.6 9.7 9.7 9.7
Margin (dB)
15.5 18.2 16.2 21.2 25.7 26.2
Limit (dBV)
55.8 53.5 50.0 46.0 46.0 46.0
Test Engineer: Ryan Chen
Version: 01-November-2017
Page: 23 of 37
FCC ID JBP_B
Test Report
Intertek Report No.: 190228019SZN-001
EXHIBIT 4 EQUIPMENT PHOTOGRAPHS
Version: 01-November-2017
Page: 24 of 37
FCC ID JBP_B
Test Report
4.0 Equipment Photographs
Intertek Report No.: 190228019SZN-001
For electronic filing, photographs of the tested EUT are saved with filename: external photos.pdf and internal photos.pdf.
Version: 01-November-2017
Page: 25 of 37
FCC ID JBP_B
Test Report
Intertek Report No.: 190228019SZN-001
EXHIBIT 5 PRODUCT LABELLING
Version: 01-November-2017
Page: 26 of 37
FCC ID JBP_B
Test Report
5.0 Product Labelling
Intertek Report No.: 190228019SZN-001
For electronics filing, the FCC ID label artwork and the label location are saved with filename: label.pdf.
Version: 01-November-2017
Page: 27 of 37
FCC ID JBP_B
Test Report
Intertek Report No.: 190228019SZN-001
EXHIBIT 6 TECHNICAL SPECIFICATIONS
Version: 01-November-2017
Page: 28 of 37
FCC ID JBP_B
Test Report
6.0 Technical Specifications
Intertek Report No.: 190228019SZN-001
For electronic filing, the block diagram of the tested EUT is saved with filename: block.pdf.
Version: 01-November-2017
Page: 29 of 37
FCC ID JBP_B
Test Report
Intertek Report No.: 190228019SZN-001
EXHIBIT 7 INSTRUCTION MANUAL
Version: 01-November-2017
Page: 30 of 37
FCC ID JBP_B
Test Report
7.0 Instruction Manual
Intertek Report No.: 190228019SZN-001
For electronic filing, a preliminary copy of the Instruction Manual is saved with filename: manual.pdf.
This manual will be provided to the end-user with each unit sold / leased in the United States.
Version: 01-November-2017
Page: 31 of 37
FCC ID JBP_B
Test Report
Intertek Report No.: 190228019SZN-001
EXHIBIT 8 MISCELLANEOUS INFORMATION
Version: 01-November-2017
Page: 32 of 37
FCC ID JBP_B
Test Report
8.0 Miscellaneous Information
Intertek Report No.: 190228019SZN-001
This miscellaneous information includes emission measuring procedure.
Version: 01-November-2017
Page: 33 of 37
FCC ID JBP_B
Test Report
8.1 Emissions Test Procedures
Intertek Report No.: 190228019SZN-001
The following is a description of the test procedure used by Intertek Testing Services in the measurements of computer peripheral operating under Part 15, Subpart B rules.
The test set-up and procedures described below are designed to meet the requirements of ANSI C63.4 - 2014.
The computer peripheral equipment under test (EUT) is placed on a styrene turntable which is four feet in diameter and approximately 0.8 meter in height above the ground plane. During the radiated emissions test, the turntable is rotated and any cables leaving the EUT are manipulated to find the configuration resulting in maximum emissions. The antenna height and polarization are varied during the testing to search for maximum signal levels. The height of the antenna is varied from one to four meters.
Detector function for radiated emissions are in QP mode from the frequency band 30MHz to 1GHz with RBW setting 120kHz and in PK & AV mode from frequency band 1GHz to 29.25GHz with RBW setting 1MHz. Detector function for conducted emissions are in QP & AV mode and IFBW setting is 9kHz from the frequency band 150kHz to 30MHz.
For radiated emission, the frequency range scanned is 30MHz to 29.25GHz. For line-conducted emissions, the range scanned is 150kHz to 30MHz with RBW setting 9KHz.
Version: 01-November-2017
Page: 34 of 37
FCC ID JBP_B
Test Report
8.2 Emissions Test Procedures (cont'd)
Intertek Report No.: 190228019SZN-001
The EUT is warmed up for 15 minutes prior to the test.
Conducted measurements are made as described in ANSI C63.4 - 2014.
Version: 01-November-2017
Page: 35 of 37
FCC ID JBP_B
Test Report
Intertek Report No.: 190228019SZN-001
EXHIBIT 9 TEST EQUIPMENT LIST
Version: 01-November-2017
Page: 36 of 37
FCC ID JBP_B
Test Report
9.0 Test Equipment List
Intertek Report No.: 190228019SZN-001
Equipment No.
SZ061-12
SZ061-08
SZ061-07 SZ056-03 SZ185-01
Equipment
Biconilog Antenna Double-Ridged Waveguide Horn Antenna Pyramidal Horn Antenna Spectrum Analyzer
EMI Receiver
SZ181-04 SZ188-01 SZ062-02
Preamplifier
Anechoic Chamber
RF Cable
SZ062-05
RF Cable
SZ062-12
SZ185-02 SZ187-01 SZ187-02 SZ188-03 SZ062-16
RF Cable
EMI Test Receiver Two-Line VNetwork Two-Line VNetwork
Shielding Room
RF Cable
Manufacturer
ETS
ETS
ETS R&S R & S Agilent ETS RADIALL
RADIALL
RADIALL
R&S R&S R&S ETS HUBER+SUHNE
R
Model No.
3142E
3115
316009
FSP30
ESCI
8449B
RFDF/A-100
RG 213U 0.0426.5GH
z 0.0426.5GH
z
ESCI
ENV21 6
ENV21 6
RFD100 CBL2BN-1m
Serial No.
001661 58
000923 46
000830 67
101148
100547 3008A0
2474 4102
--
--
--
100692
100072
100073
4100
--
Cal. Date
14-Sep-2018
14-Sep-2018
17-Mar-2018 05-Jun-2018 04-Jan-2019 15-Jan-2019 15-Dec-2018 01-Mar-2019 01-Mar-2019
01-Mar-2019 26-Oct-2018 26-Oct-2018 04-Jul-2018 16-Jan-2017 29-Oct-2018
Due Date
14-Sep-2019
14-Sep-2019
17-Mar-2019 05-Jun-2019 04-Jan-2020 15-Jan-2020 15-Dec-2020 01-Jun-2019 01-Jun-2019
01-Jun-2019 26-Oct-2019 26-Oct-2019 04-Jul-2019 16-Jan-2020 29-Oct-2019
***********************************************End of Report**********************************************
Version: 01-November-2017
Page: 37 of 37
FCC ID JBP_B
Microsoft Word for Office 365 Related Documents
TCL 65S425 LED TV FCC Test Report
TTE Technology Inc. LED TV Test Report for FCC Certification
TCL 65S425-CA 65-inch 4K Roku Smart LED TV Specifications
TCL Serie S425 Roku TV: Specifications and Features
TCL 4-Series Roku TV User Guide: Setup, Features, and Operation
TCL 65S425 Television Energy Guide
TCL Roku TV 4-Series Quick Start Guide and Warranty Information
TCL 4-Series Roku TV Quick Start Guide and Setup
