Xtreme Bluetooth Home Theater Soundbar

Model: XBS9-1076

Safety Instructions

Please read and understand all instructions before using this product. Failure to follow instructions may void the warranty.

Use caution with loud sounds as they can cause permanent hearing loss.
Only use the provided Power Adapter.
Do not stare at LEDs.
Do not operate the unit other than as stated in this manual.
Do not leave the device unattended while in use.
Do not drop, puncture, or disassemble the product.
Keep the product away from moisture and liquids.
Avoid exposing the product to dirt, sand, or similar matter.
Do not expose the product to direct sunlight for extended periods, as this may cause damage.
Do not expose the product to open flames.
Do not use the product in a strong magnetic field.
Clean the unit with a soft, dry cloth. Do not use corrosive cleaners.
Do not attempt to repair the device or open the unit, as this will void the warranty.
Do not charge or use the product if it has been submerged in water or if water has entered the product.
Do not expose the product to heat sources, flames, or leave it in a hot vehicle.
Use the product in a location with a temperature between 32°F and 95°F (0°C to 35°C).
Do not place the product where it could be crushed or punctured.
This product is not a toy. Keep out of reach of children and those requiring supervision.
Do not use abrasive cleaning solvents.

FCC Caution

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

One Year Warranty

Xtreme warrants its products for one year against defects in manufacturing under regular consumer use with the original receipt of retail purchase. To obtain warranty service, please contact Customer Service at customerservice@xtremecables.com. Customers outside of the U.S. will be responsible for shipping and handling charges for replacements not due to manufacturing defects.

Xtreme's warranty is limited to its products only and does not cover the replacement or repair cost of any third-party accessory, electronic device, or personal property.

Content is subject to change without prior notice. Some content may differ from how the product works with your specific device.

Introduction

Please read this entire manual before use, including all warnings. Keep this manual for future reference.

Features

Bluetooth® 32" soundbar for use with your home theater system.
Mount seamlessly to your wall with the built-in bracket or place on top of a console.
Built-in controls for power, mode, play/pause, and volume.
IR remote control included (requires 2xAAA batteries, not included).
Compatible with all Bluetooth® enabled devices.

What's Included

Bluetooth® Soundbar Speaker
12V Power Adapter
Remote Control (2xAAA Batteries Required, Not Included)
User Manual

Specifications

DC Power Input: 5VDC/2A
Product size: 820*58*60MM
Speaker: (x2) 2", 4 Ohm, 5W
Digital Inputs: 24Bit/192kHz
Power: (x2) 5W
Bluetooth Range: >10M
Recommended Operating Temperature: -20°C to +60°C

Product Overview & Functions

Top of Soundbar

Mode Selection
Play/Pause
Decrease Volume
Increase Volume

Rear of Soundbar

On/Off Switch
DC Power Input
Aux 3.5mm Input
Digital Optical Input
Digital Coaxial Input
Power LED

Remote Control

Power On/Off
Bluetooth Mode
3.5mm Aux Mode
Coaxial Mode
S/PDIF Optical Mode
Mute Mode
Select Previous
Increase Volume
Select Next
Decrease Volume
Play & Pause

Power On/Off

Turn the unit on via the On/Off switch on the back of the unit or via the remote control.

Pairing Devices to the Speaker

Power on the Soundbar.
Keep the distance between your device and the speaker within 3 feet (for pairing only).
Activate the Bluetooth function on your source device.
Select "Xtreme XBS9-1076" from the devices list and follow the on-screen prompts to finish the pairing process.
Note: After successfully pairing once, the devices will remember each other. To manually enter pairing mode, press and hold the Play/Pause button on the top of the Soundbar until the Soundbar prompts you to pairing mode. Follow the above instructions to complete the pairing process.
After successfully pairing the speaker to your device, a tone will sound.
Once paired, audio will be received and will sound from the Soundbar.
Adjust the volume on the top of the speaker, or via the wireless remote.

Mode Operations

Press the dedicated mode buttons on the remote control or the "M" button on the top of the speaker to change modes. The speaker will sound out what mode is selected. Depending on certain modes that require external devices to be connected, whilst switching modes, that mode may be skipped because nothing is connected and detected.

Bluetooth Mode

Stream audio from your smartphone, TV, or other Bluetooth enabled device to the speaker. See Pairing instructions for more information on device pairing. Use the remote control or playback control on the speaker.

Aux 3.5mm Input Mode

Connect a 3.5mm cable between the input of the Soundbar and the output of the source device. The Soundbar should automatically switch to Aux Mode; if this does not happen, manually select Aux mode via the remote control or the "M" button on the top of the Soundbar.

Lower the volume on the Soundbar and begin audio playback from your source device. Once an ideal playback level from your source device has been set, control the overall volume from the Increase and Decrease buttons on the top of the Soundbar or the remote control.

S/PDIF Optical Input Mode

Connect an optical cable between the Soundbar and the source device. The Soundbar should automatically switch to S/PDIF Optical Mode; if this does not happen, manually select S/PDIF Optical mode via the remote control or the "M" button on the top of the Soundbar.

Lower the volume on the Soundbar and begin playback on the source device. Raise the volume of the Soundbar via the Increase and Decrease buttons on the top of the Soundbar.

Digital Coaxial Input Mode

Connect a Coaxial cable between the Soundbar and the source device. The Soundbar should automatically switch to Coaxial Mode; if this does not happen, manually select Coaxial mode via the remote control or the "M" button on the top of the Soundbar.