SONOFF BMT01 BBQ Meat Thermometer User Manual

Introduction

SONOFF BBQ Meat Thermometer is a smart barbecue thermometer. Insert the heat-resistant probe into the center of the food, and monitor the real-time temperature on the device screen or the eWeLink app. It will alert you when the Preset Temp. is reached, helping you effortlessly grill delicious barbecue.

• ?️ Temperature Detection
• ? App Monitoring
• ? Temp. Alert
• ⏱️ Timer Reminder

Key Features

• ? Real-Time Temp. Chart
• ℉/℃ Reading Switch
• ? Backlit Display
• ? Quick Refresh

Screen Display Instructions

The device screen displays the following information:

1. Temperature unit: Displays temperature in Fahrenheit (°F) or Celsius (°C).
2. Connection icon:
   • Flashing: The device is in pairing mode.
   • Solid: Connected to the eWeLink App.
   • Off: Not connected to the eWeLink App.
3. Battery level: Indicates the remaining battery power.
4. Probe temperature: Shows the current temperature detected by the probe.
5. Temperature corresponding probe: Indicates which probe is being monitored.

Device Instructions

The device has the following components:

1. Power button: Press and hold for 5 seconds to power on. In the powered-on state, press and hold for 5 seconds to power off.
2. Function button:
   • Long touch for 5 seconds: Device enters pairing mode (pairing time 180s).
   • Short touch: Turns on the backlit mode or switches to the next probe temperature.
3. Device bracket: For hanging or attaching the device.
4. Probe interface: Port for connecting the temperature probe.
5. Battery protection cover: Cover for the battery compartment.

Specifications

*This product is only suitable for safe use at altitudes below 2000m.

Download the eWeLink App

Please download the "eWeLink" App from Google Play Store or Apple App Store.

Search for "eWeLink" [magnifying glass icon] or visit the app stores.

Powering On the Device

1. Remove the battery protection cover, then pull out the device battery insulation sheet to power the device.
2. When the device is used for the first time, it will enter pairing mode by default after being powered on, and the connection icon ? will flash.
3. If pairing is not completed within three minutes, the device will exit pairing mode. To re-enter pairing mode, long touch the function button on the screen for 5 seconds until the connection icon ? starts flashing.

Adding the Device via QR Code

1. Open the eWeLink app and enter "Scan".
2. Scan the QR code on the device.
3. Select "Add Device".
4. Long touch the function button on the device screen for 5 seconds.
5. Check the status of the connection icon (it should be flashing).
6. Search for the device and start connecting.
7. Once the device is added successfully, you will see a confirmation message.

Usage Instructions

1. Insert the probe connectors into the ports on both sides of the BMT01, then insert the probe into the food you wish to monitor (e.g., beef, lamb).
2. Set the Preset Temp. in the eWeLink App. When the probe temperature rises to the Preset Temp., the device and mobile phone will trigger an alarm reminder.

*If the device does not detect the probe within 10 minutes, or if the probe's temperature does not exceed 50°C within 24 hours, it will automatically power off. To turn the device on, press and hold the side button for five seconds.

Usage Demonstration

The device is used by inserting the probe into food being cooked on a grill. The temperature is monitored via the device screen or the eWeLink app, which provides alerts when a preset temperature is reached.

Components and Warnings

Components:

• ① Probe clip
• ② BBQ meat thermometer probe sensor
• ③ BBQ meat thermometer (main unit)
• ④ Magnetic hook

*The magnetic hook should be kept away from high temperatures to prevent demagnetization. *After use, place the devices into the storage bag.

WARNINGS:

• ⚠️ This product is equipped with a food-grade probe. Please remove the plastic protective cover from the probe before use. The probe is sharp, so handle with care to avoid injury.
• ⚠️ Avoid touching the probe directly with your hands in high-temperature environments to prevent burns.
• ⚠️ Keep the probe away from open flames. Grilling over open flames can easily produce carcinogens like polycyclic aromatic hydrocarbons and nitrosamines. The probe's temperature measurement range is 32~572°F (0~300℃); long-term exposure to open flames may cause malfunction.
• ⚠️ The main unit is not resistant to high temperatures. Please keep it away from the grill during use.
• ⚠️ The magnetic hook should be kept away from high temperatures to prevent demagnetization. It is recommended to attach it to the grill legs.
• ⚠️ This product is not suitable for children. Please keep it out of reach of children.
• ⚠️ This product contains AAA batteries. Please keep new and old batteries out of reach of children.

Regulatory Information

ISED Notice (Canada)

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus complies with Canadian ICES-003(B). This device complies with RSS-247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference.

ISED Radiation Exposure Statement: This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC Compliance Statement (USA)

1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC ID: 2APN5BMT01

Battery Safety and Disposal

⚠️ Chemical Burn Hazard: Do not ingest battery.

⚠️ If the battery compartment does not close securely, stop using the product and keep it away from children. If batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

⚠️ Do not replace a battery with an incorrect type.

⚠️ Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, can result in an explosion.

⚠️ Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas.

⚠️ A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.

This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

Batteries are to be inserted with the correct polarity. If the appliance is to be stored unused for a long period, the batteries are removed. The supply terminals are not to be short-circuited.

Battery Disposal:

This appliance contains AAA batteries, which contain hazardous chemicals. Make sure to strictly follow local regulations regarding the disposal and recycling of batteries. DO NOT dispose of the batteries in a regular waste disposal container.

Dispose of the batteries in a suitable recycling container only after fully discharging it.

Batteries that are swollen, involved in a crash, come into contact with liquid, damaged, or leaky must be disposed of properly. DO NOT use any batteries in such a condition to avoid damage or injury. Contact a professional battery disposal or recycling agent for further assistance.

DO NOT use metal short-circuited batteries; otherwise, the batteries may leak, catch fire, or explode.

This appliance contains non-rechargeable batteries; these batteries are not to be recharged.

Warning: Under normal use, this equipment should be kept a separation distance of at least 20 cm between the antenna and the body of the user.

EU Declaration of Conformity

Shenzhen Sonoff Technologies Co., Ltd. declares that the radio equipment type BMT01 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at: https://sonoff.tech/compliance/

For CE frequency:

• EU Operating Frequency Range: BLE: 2402-2480MHz
• EU Output Power: BLE ≤10dBm

WEEE Disposal and Recycling Information

All products bearing the WEEE symbol (waste electrical and electronic equipment) should not be mixed with unsorted household waste. Instead, hand over waste equipment to a designated collection point for recycling. Correct disposal and recycling help prevent negative consequences to the environment and human health. Please contact local authorities for more information.

Manufacturer Information

Manufacturer: Shenzhen Sonoff Technologies Co., Ltd.

Address: 3F & 6F, Bldg A, No. 663, Bulong Rd, Shenzhen, Guangdong, China

ZIP code: 518000

Service email: support@itead.cc

Website: sonoff.tech

Made in China