DJI Matrice 3TD/3D Compliance and Regulatory Information

This document provides essential compliance and regulatory information for the DJI Matrice 3TD and DJI Matrice 3D drones.

FCC Compliance Notice

Supplier's Declaration of Conformity

Product name: DJI Matrice 3TD/DJI Matrice 3D

Model Number: M3TD/M3D

Responsible Party: DJI Research LLC

Responsible Party Address: 17301 Edwards Road, Cerritos, CA 90703

Website: www.dji.com

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Information

The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm during normal operation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

ISED Compliance Notice

CAN ICES-003 (A) / NMB-003(A)

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

The equipment complies with RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

KC Compliance Notice

해당무선설비는 운용 중 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다. (This wireless equipment may cause radio wave interference during operation, so services related to human safety cannot be provided.)

해당 무선설비는 운용 중 전파혼신 가능성이 있음 (This wireless equipment may cause radio wave interference during operation.)

NCC Compliance Notice

取得審驗證明之低功率射頻器材,非經核准,公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻器材之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。前述合法通信,指依電信管理法規定作業之無線電通信。低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。應避免影響附近雷達系統之操作。供遙控無人機類似器材遙控器之使用,應符合目的的事業主管機關有關遙控無人機之管理規定. (This low-power radio frequency equipment has obtained type approval. Without authorization, any company, firm, or user shall not alter the frequency, increase the power, or change the characteristics and functions of the original design. The use of low-power radio frequency equipment shall not affect flight safety and interfere with lawful communication; if interference is found, it shall be stopped immediately and improved until no interference occurs. Lawful communication refers to radio communication operated in accordance with the provisions of the Telecommunications Management Act. Low-power radio frequency equipment must tolerate interference from lawful communication or industrial, scientific, and medical radio frequency radiating electrical equipment. It should avoid affecting the operation of nearby radar systems. The use of remote controls for equipment similar to remote-controlled drones shall comply with the management regulations for remote-controlled drones issued by the competent authority.)

EU & UK Compliance Notice

[CE Mark] [UKCA Mark]

EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device (DJI MATRICE 3TD/DJI MATRICE 3D) is in compliance with the essential requirements and other relevant provisions of the Directive 2014/53/EU.

A copy of the EU Declaration of Conformity is available online at www.dji.com/euro-compliance

EU contact address: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany

GB Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device (DJI MATRICE 3TD/DJI MATRICE 3D) is in compliance with the essential requirements and other relevant provisions of Radio Equipment Regulations 2017.

A copy of the GB Declaration of Conformity is available online at www.dji.com/euro-compliance

Environmentally Friendly Disposal

[WEEE Recycling Symbol]

Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.

Other Regional Notices

Thailand Warning message: เครองโทรคมนาคมและอปกรณน มความสอดคลองตามขอกาหนดของ กทช. (This telecommunications equipment is in compliance with the requirements of the NBTC.)

Mexico Warning message: "La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada."

Brazil Warning message: Informações sobre Regulamentação. Este equipamento está certificado e homologado pela ANATEL. Para maiores informações, consulte o site da ANATEL: www.anatel.gov.br. Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados.

French Recycling Info: Cet appareil et ses accessoires se recyclent. À DÉPOSER EN MAGASIN OU À DÉPOSER EN DÉCHÈTERIE. Points de collecte sur www.quefairedemesdechets.fr

This content is subject to change without prior notice.

For more information, visit: https://enterprise.dji.com/dock-2/downloads

	DJI Matrice 3D Series User Guide: Features, Specifications, and Operation Explore the DJI Matrice 3D Series drone with this comprehensive user guide. Learn about its infrared sensing, vision systems, RTK module, specifications, and operational procedures.
	DJI Matrice 3D Series User Guide - Overview, Specifications, and Operation Comprehensive user guide for the DJI Matrice 3D Series aircraft, covering its features, specifications, setup, operation, and linking procedures. Includes detailed information on components, preparation, and usage.
	DJI FlightHub 2 Private Version Firmware Compatibility This document outlines the required firmware versions for DJI aircraft, remote controllers, and the DJI Pilot 2 app to ensure compatibility with the FlightHub 2 Private Version.
	DJI Care Enterprise Compatibility Overview for Drones and Payloads A comprehensive overview of DJI Care Enterprise plan compatibility across DJI drone models, payloads, accessories, and remote control solutions, detailing coverage for various DJI products.
	DJI Dock 2 / DJI Matrice 3D Series Maintenance Manual Comprehensive maintenance manual for the DJI Dock 2 and DJI Matrice 3D Series aircraft, covering inspection, upkeep, and after-sales service procedures to ensure optimal performance and safety.
	DJI Thermal Analysis Tool 3: User Guide for Thermal Image Analysis This user guide provides comprehensive instructions for using the DJI Thermal Analysis Tool 3 software to analyze and process thermal images from DJI drones and Zenmuse cameras. It covers software features, operating system requirements, supported devices, and detailed explanations of analysis tools and parameters.
	DJI Dock 2 User Manual - Battery and Remote Controller Operation This user manual provides comprehensive instructions for operating the DJI Dock 2, focusing on battery management, remote controller functions, and system settings. Learn about battery installation, charging, self-heating, and status indicators. Discover how to pair and use the remote controller for aircraft operation, including flight modes, control sticks, and button functions. The manual also covers aircraft compass calibration, gimbal calibration, and advanced features like DJI FlightHub 2 for cloud management and third-party platform integration. Specifications for the DJI Dock 2 and its associated aircraft are detailed, along with compliance notices and disposal guidelines.
	DJI Drones and Accessories Compatibility with DJI Care Enterprise Plans A comprehensive compatibility guide detailing which DJI drones, compatible products, and accessories are supported by DJI Care Enterprise Basic, DJI Care Enterprise Basic (2-year plan), and DJI Care Enterprise Plus.