Instruction Manual for SENECA models including: Z-KEY, Gateway ModBUS, Z-KEY Gateway ModBUS, ModBUS
Z-KEY | Gateway Profinet | SENECA
Z-KEY | Gateway ModBUS | SENECA
File Info : application/pdf, 4 Pages, 295.51KB
DocumentDocumentINSTALLATION MANUAL Z-KEY Z-KEY-P PRELIMINARY WARNINGS The word WARNING preceded by the symbol indicates conditions or actions that put the user's safety at risk. The word ATTENTION preceded by the symbol indicates conditions or actions that might damage the instrument or the connected equipment. The warranty shall become null and void in the event of improper use or tampering with the module or devices supplied by the manufacturer as necessary for its correct operation, and if the instructions contained in this manual are not followed. WARNING: The full content of this manual must be read before any operation. The module must only be used by qualified electricians. Specific documentation is available via QR-CODE shown on page 1. The module must be repaired and damaged parts replaced by the Manufacturer. The product is sensitive to electrostatic discharges. Take appropriate measures during any operation. Electrical and electronic waste disposal (applicable in the European Union and other countries with recycling). The symbol on the product or its packaging shows the product must be surrendered to a collection centre authorized to recycle electrical and electronic waste. DOCUMENTATION Z-KEY DOCUMENTATION Z-KEY-P SENECA s.r.l.; Via Austria, 26 35127 PADOVA ITALY; Tel. +39.049.8705359 - Fax +39.049.8706287 CONTACT INFORMATION Technical support support@seneca.it Product information sales@seneca.it This document is the property of SENECA srl. Copies and reproduction are prohibited unless authorised. The content of this document corresponds to the described products and technologies. Stated data may be modified or supplemented for technical and/or sales purposes. MI00369-8-EN INSTALLATION MANUAL 1/4 MODULE LAYOUT 17.5 mm 111 mm 102.5 mm Dimensions: 17.5 x 102.5 x 111 mm, Weight: 100 g; Enclosure: PA6, black SIGNALS VIA LED ON FRONT PANEL LED PWR SD / COM Z-KEY version only SD / COM Z-KEY-P version only TX1 RX1 TX2 RX2 ETH ACT Green ETH LNK Yellow STATUS ON Flashing Flashing Off Flashing Flashing Flashing Flashing Flashing ON LED meaning The device is powered correctly Accessing the microSD card Profinet communication active No Profinet communication Data transmission on port #1 RS485 Data receipt on port #1 RS485 Data transmission on port #2 RS485/RS232 Data reception on port #2 RS485/RS232 Packet transmission on Ethernet port Ethernet connection present MI00369-8-EN INSTALLATION MANUAL 2/4 TECHNICAL SPECIFICATIONS STANDARDS EN61000-6-4 Electromagnetic emissions, industrial environment. EN61000-6-2 Electromagnetic immunity, industrial environment. EN60950-1 Security in information processing equipment Additional notes: a 1 A delayed fuse must be installed near the module, in series with the power supply connection. USB INSULATION Comm. RS485 (IDC10) ETH Comm. Power Supply RS485/232 1500 Vac 11..40 Vdc / 19..28 Vac (IDC10) Temperature: ENVIRONMENTAL CONDITIONS Humidity: Altitude: Storage temperature: Protection rating: -25 °C + 65 °C 30% 90% non condensing. Up to 2000 m above sea level -30 °C + 85 °C IP20 (Not evaluated by UL) ASSEMBLY IEC EN60715, 35mm DIN rail in vertical position. CONNECTIONS 3-way removable screw terminals, pitch 5 mm Rear connector IDC10 for DIN bar 46277 RJ45 front connector SMA antenna connector side micro USB port microSD card slot POWER SUPPLY Voltage: 11 40 Vdc; 19 28 Vac 50 60 Hz Absorption: Max. 1,5W RS242 or RS485 switchable on terminal 10 - 11 - 12 COMMUNICATION Maximum Baud rate 115 k, maximum cable length RS232 < 3m PORTS RS485 IDC10 rear connector: Maximum Baud rate 115 k. RJ45 front Ethernet connector: 100 Mbit/s, maximum distance 100 m ATTENTION The device may only be powered by a power supply unit with a limited energy electric circuit max. 40Vdc / 28Vac Max output in accordance with CAN/CSA-C22.2 No. 61010-1-12 / UL Std. No. 61010-1 (3rd Edition) chapter 6.3.1/6.3.2 and 9.4 or class 2 according to CSA 223/UL 1310. FACTORY IP ADDRESS The default module IP address is static: 192.168.90.101 WEB SERVER To access the maintenance Web Server with 192.168.90.101 factory IP address: Default user: admin, Default password: admin, http://192.168.90.101 MI00369-8-EN INSTALLATION MANUAL 3/4 IDC10 CONNECTOR RS485 GND Power Supply AC / + RS485 A Power Supply AC / - RS485 B 1 IDC 10 The illustration shows the meanings of the various IDC10 connector pins if signals are to be sent via them directly. SETTING THE DIP-SWITCHES SETTINGS OF FACTORY PARAMETERS This procedure returns the IP to the factory one (192.168.90.101) and the Web Server/ FTP server access credentials to user: admin and password: admin. 1. Turn the module off and set all eight SW1 DIP-switches to ON. 2. Turn on the module and wait 10 seconds. 3. Turn the module off and set all eight SW1 DIP-switches to OFF. KEY 1 ON 0 OFF RS232/RS485 SETTING: RS232 or RS485 configuration on terminals 10-11-12 (serial port 2) 1 ON 0 OFF SW2 RS232 ACTIVATION RS485 ACTIVATION INSTALLATION REGULATIONS The module has been designed for vertical installation on a DIN 46277 rail. For optimal operation and long life, adequate ventilation must be provided. Avoid positioning ducting or other objects that obstruct the ventilation slots. Avoid mounting modules over heat-generating equipment. Installation in the bottom part of the electrical panel is recommended. ATTENTION These are open-type devices and intended for installation in an end enclosure / panel offering mechanical protection and protection against spread of fire. ELECTRICAL CONNECTIONS CAUTION To meet the electromagnetic immunity requirements: - use shielded signal cables; - connect the shield to a preferential instrumentation earth system; - separate shielded cables from other cables used for power installations (transformers, inverters, motors, etc...). POWER SUPPLY Tens. aus. 1 Vac/Vdc 2 Vac/Vdc 3 SERIAL PORT 2: RS485 SW2 = OFF GND 10 A (+) 11 B (-) 12 SERIAL PORT 2: RS232 SW2 = ON GND 10 RX 11 TX 12 ATTENTION Use only copper or copper-clad aluminium or AL-CU or CU-AL conductors MI00369-8-EN INSTALLATION MANUAL 4/4