Instruction Manual for BLAUPUNKT models including: TPMS TY1.0, Wireless Real-Time Tire Pressure Monitoring System
TPMS TY1.0 E/V - Blaupunkt Tire Pressure Monitoring System
TOYOTA PLUG & PLAY TPMS TY1.0 Operating and Installation Instructions Enjoy it. CAUTIONS Safety Notes This TPMS (Tire Pressure Monitoring System) has been manufactured according to established safety guidelines. However, dangers may still occur if the safety notes in this manual is not observed. This manual is intended to familiarize the user with the TPMS's important functions. Read this carefully, prior to using the appliance. Keep this manual in an easily accessible location. In addition, do observe the instructions of the devices used in conjunction with this appliance. Road Safety Always observe the following notes for road safety: · Device must be used in a way that compliments the safety of the user when driving the vehicle. It is recommended for the user to park at an appropriate location when examining the tires in case of abnormal alert. General Safety · Device is intended for installation and operation in a vehicle with 12V vehicle system outage, hence the device must be installed 500mm away from the DVD or high power equipment to prevent signal disruption. · Do not dismantle or modify the device. Installation or repair should be performed by a specialist. Blaupunkt is not liable for any loss or damage resulting from unauthorized disassembly or modification to the device. · Device is designed to monitor tire pressure and temperature only. Driver is responsible for the upkeep of the tires. · Blaupunkt is not liable in case of loss of sensors. Contact your Blaupunkt dealer to purchase new sensors. · Package comes with pre-set sensor for designated tires. In case of sensor replacement or change of sensor location, ensure the sensor are reprogrammed before operating. · Please do not operate the device under such conditions (extremely high temperature or extremely low temperature); ensure that the temperature within the car ranges from -30°C to 80°C before you begin installation process and during operation. · For abnormalities, please refer to the "Troubleshooting" section. Consult with Blaupunkt dealer for further examining, in case if the problem cannot be resolved. This manual may be updated from time to time without any notice. Disclaimer In no event shall Blaupunkt be liable for any direct, indirect, punitive, incidental, special consequential damages to property or life and whatsoever arising out of or connected with the use or misuse of our products. USA & CANADA: This product is not intended for sale in the United States and Canada. If purchased in the U.S. or Canada, this product is purchased on as-is basis. No warranty, whether expressed or implied is provided in the U.S. or Canada. 1 STRUCTURE & FUNCTIONS Display 23.5mm 1 2 34mm 3 6 45 External Sensor 1 2 3 4 5 6 48.1mm Valve Sensor 1 2 3 4 18.0mm Functions Display 1. Data Display 2. Pressure Unit 3. Display Battery Status 4. OK Button 5. Setting Button 6. TPMS Alarm Icon External Sensor 1. Sensor Cover 2. Battery Holder 3. Battery 4. Sensor 5. Rubber Seal 6. Base Valve Sensor 1. Dust Cap 2. Aluminium Alloy Nut 3. Aluminium Alloy Valve 4. Transmitter 2 SPECIFICATIONS Sensor Operating frequency Battery voltage Operating temperature Pressure range 433.92 ± 0.05MHz 1.8V ~ 3.3V -30°C ~ 60°C (External Sensor) -40°C ~ 105°C (Valve Sensor) 0~8 Bar / 0~116 PSI Display Operating current Operating frequency Operating voltage Operating temperature Pressure display range <20mA 433.92± 0.05MHz +12V -30°C ~ 80°C 0~6.8Bar/0~99PSI Default Value High pressure value Low pressure value High temperature value 3.1 Bar / 45 PSI 1.8 Bar / 26 PSI 80°C Precision Temperature Pressure +/-2°C 0.1 Bar / 1.5 PSI Temperature unit Air pressure unit 1 °C = 33.8 °F = 274.15 K 1 Bar = 14.5 PSI = 100 Kpa = 1.02Kgf/cm2 Accessories Display 1x Power cable TPMS TY1.0E 4x external sensor TPMS TY1.0V 4x anti-theft nuts 1x spanner (keep in car) 4x built-in battery 4x valve sensor 4x warning label 3 EXTERNAL SENSOR INSTALLATION 1. Remove the valve cap. 4. Tighten up the nut to the sensor by using the spanner. 2. Screw in the nut. 5. Spray soap water on the nozzle to check for leakage problem. 3. Screw on the sensor. 6. Clean the area before using it. 4 EXTERNAL SENSOR BATTERY REPLACEMENT 1. Unscrew the nut. 4. Replace new battery. VALVE SENSOR INSTALLATION 1. Remove the original air valve from the wheel barrel. 4. Rebalance the wheel to ensure radial uniformity. 2. Unscrew the sensor. 5. Refer to "Sensor Installation" steps. 2. Install & adjust the valve sensor onto the wheel barrel. Screw & tighten the nut & valve. 5. Reinstall the balanced wheel onto the vehicle. 3. Unscrew the sensor cover by using spanner. 3. Inflate the tire after installation. 5 6 DISPLAY INSTALLATION 1. Disassemble blind switch from the original vehicle switch panel. 3. Embed the display into the empty switch slot. 2. Connect the power cable to the display. Then, connect the power cable to ACC & ground wire. (Refer to the Wiring Diagram) 4. The display is turned on when ACC on. DIFFERENT SCENARIO Front Left (FL) Front Right (FR) Rear Left (RL) Rear Right (RR) 1. Normal · Displays real time tire pressure & temperature of 4 tires. 4. High Temperature · Di- Di- Di- Di- Di- 5. Sensor Failure 2. High Pressure · Di- Di- Di- Di- Di- 6. Low Battery · Di- Di- Di- Di- Di- WIRING DIAGRAM Connect to ACC Connect to Ground Wire Red Black 3. Air Leakage · Di- Di- Di- Di- Di- 7 8 SETTING 1. Sensor Pairing Setting (It is required only when the sensors has switched location or be replaced) a) Press & hold setting button to enter setting interface. Di- b) After entering the setting interface, P1 will be shown. d) · External sensor - Disassemble the external sensor from the front left tire & reinstalled, for sensor ID pairing activation. · Valve sensor - Releasing the air from tire continously instead of intermittently, ensure that the releasing process is not less than 8 second. - Do not exceed the maximum pressure of tire during inflating. e) When system receives the signal, you will hear "Di-" which indicates successful sensor pairing (new sensor ID will be displayed). Then, it will continue to next order. SETTING 2. Tire Position Exchange Setting (It is required only when the tires has switched location) a) Press & hold setting button to enter setting interface. Di- b) Press setting button again, P2 will be shown. Thresold Value Setting a) Press & hold setting button to enter setting interface. Di- b) Press setting button twice, P3 will be shown. c) Press OK button to enter pairing mode. Press the setting button to switch the preferred position, press OK button to select. Press & hold setting button again to return back to the first pairing order. (Pairing order : Front Left > Front Right > Rear Right > Rear Left) · Ensure that there is only one of the tire with sensor is activated during pairing, otherwise there is no guarantee that the sensor ID that really needs to be paired will be paired into the receiver. · To cancel the current pairing process by pressing return key, however pairing process cannot be canceled after prairing process is successful. c) Press OK button, the digits on the top left & top right will flash. Press the setting button again to switch preferred position, press OK button to select. You will hear "Di- Di-" which indicates successful. c) Press OK button, then press the setting button to switch between thresold value interface (High Pressure Value & Low Pressure Value ). Select the preferred interface by pressing OK button. The digit will flash then press the setting button to adjust the preferred value & press OK button to select. · High Pressure Value Setting Interface d) Press & hold the setting button to exit setting interface. 9 10 SETTING · Low Pressure Value Setting Interface d) Press & hold the setting button to exit setting interface. 4. Unit Switching a) Press & hold setting button to enter setting interface. c) Press OK button, then press the setting button to switch pressure unit. Press OK button to select the preferred unit. d) Press & hold the setting button to exit setting interface. TROUBLESHOOTING If any of the following problem occur, please resort to Troubleshooting for the possible solutions. Consult Blaupunkt authorized dealer if problem persist. Problems Air leakage after sensor installation No tire data are displayed after completing installation Missing or lost sensor External sensor battery low Change of tire location Solutions The tire valves may not be universal standard, please check with the local workshop. Ensure ACC is turned on. Please purchase new sensor. Please replace with battery CR1632. Please reprogram the corresponding sensors. Di- b) Press setting button thrice, P4 & default pressure unit will be shown. 11 12 Designed and engineered by Blaupunkt Competence Centre TPMS TY1.0E 1 311 21 008 45 01 TPMS TY1.0V 1 311 21 009 45 01Adobe PDF Library 16.0.5 Adobe InDesign 17.1 (Windows)