User Guide for MSI models including: PRO MP241X LCD Monitor, PRO MP241X, LCD Monitor, Monitor
Quick Start Guide. Accessories. Stand. Stand Base. External Power Supply & Power Cord. Cables. High Speed HDMI™ Cable (Optional). ⚠Important.
2 giorni fa — Safety Instructions. ∙ Read the safety instructions carefully and thoroughly. ∙ All cautions and warnings on the device or User Guide should be noted.
File Info : application/pdf, 22 Pages, 1.10MB
DocumentDocumentPRO Series
LCD Monitor
PRO MP241X (3BA9)
User Guide
Contents
Getting Started.............................................................................................................. 3 Package Contents................................................................................................... 3 Installing the Monitor Stand................................................................................... 4 Adjusting the Monitor ............................................................................................. 5 Monitor Overview.................................................................................................... 6 Connecting the Monitor to PC ................................................................................ 7
OSD Setup ..................................................................................................................... 8 OSD Keys ................................................................................................................ 8 OSD Setup Menus ................................................................................................. 10
Specifications.............................................................................................................. 13 Preset Display Modes ................................................................................................ 15 Troubleshooting.......................................................................................................... 16 Safety Instructions...................................................................................................... 17 TÜV Rheinland Certification....................................................................................... 19 Regulatory Notices..................................................................................................... 20
Revision V1.2, 2023/06
2 Contents
Getting Started
This chapter provides you with the information on hardware setup procedures. While connecting devices, be careful in holding the devices and use a grounded wrist strap to avoid static electricity.
Package Contents
Monitor
PRO MP241X
Documentation
Quick Start Guide
Stand
Accessories
Stand Base
External Power Supply & Power Cord
Cables
High Speed HDMITM Cable (Optional)
Important
Contact your place of purchase or local distributor if any of the items is damaged or missing.
Package contents may vary by country.
The included power cord is exclusively for this monitor and should not be used with other products.
Getting Started 3
Installing the Monitor Stand
1. Leave the monitor in its protective foam packaging. Align and gently push the stand bracket towards the monitor groove until it locks in place.
2. Align and gently push the base towards the stand until it locks in place. 3. Make sure the stand assembly is properly installed before setting the monitor
upright.
Important
Place the monitor on a soft, protected surface to avoid scratching the display panel. Do not use any sharp objects on the panel.
1 2
4 Getting Started
Adjusting the Monitor
This monitor is designed to maximize your viewing comfort with its adjustment capabilities.
Important
Avoid touching the display panel when adjusting the monitor. -5° +15°
Getting Started 5
Monitor Overview
1 3
2
4
5
6
1 OSD Keys 2 Power Button 3 Kensington Lock 4 HDMITM Connector
Supports 1920x1080@75Hz as specified in HDMITM 1.4b.
5 D-Sub Port 6 Power Jack
6 Getting Started
Connecting the Monitor to PC
1. Turn off your computer. 2. Connect the video cable from the monitor to your computer. 3. Assemble the monitor power adapter & power cord. (Figure A) 4. Connect the power adapter to the monitor power jack. (Figure B) 5. Plug the power cord into the electrical outlet. (Figure C) 6. Turn on the monitor. (Figure D) 7. Power on the computer and the monitor will auto detect the signal source.
B D
C A
Getting Started 7
OSD Setup
This chapter provides you with essential information on OSD Setup.
Important
All information is subject to change without prior notice.
OSD Keys
The monitor comes with a set of OSD Keys that help to control the On-Screen Display (OSD) menu.
1 2 3 4
8 OSD Setup
OSD Keys
1M
2
3
4E
Hot Key (When OSD is OFF)
OSD Setup (When OSD is ON)
Activating the OSD Main Menu
Returning to the previous menu
Exiting from the OSD Main Menu
Used as the designated shortcut hotkey
Used as the Up/Right button to select function menus and items
Allowing upward adjustment in function values
Used as the Down/Left button to select function menus and items
Allowing downward adjustment in function values
Activating the auto adjustment function that automatically sets the horizontal/vertical position, clock and focus (for D-Sub signals only)
Used as the Enter button to enter function items
OSD Setup 9
OSD Setup Menus
Press the M key to launch the On-Screen Display (OSD) main menu and use the OSD keys to tune the desired function to suit your personal preferences.
1st Level Menu 2nd/3rd Level Menu
Brightness
0-100
Contrast
0-100
DCR
ON
OFF
Return
Exit
Mode
Standard
Movie
FPS
RTS
EyeSaver
Return
Exit
Color Temp.
Warm
Cool
User
R (0-100)
G (0-100)
B (0-100)
Return
Exit
Description Adjusting display brightness Adjusting display contrast Activating dynamic contrast Deactivating dynamic contrast Returning to the previous menu Exiting from this function menu Normal work mode Movie mode FPS game mode RTS game mode Eye protection mode Returning to the previous menu Exiting from this function menu Warm color temperature Cold color temperature Fine-tuning of Red color temperature Fine-tuning of Green color temperature Fine-tuning of Blue color temperature Returning to the previous menu Exiting from this function menu
10 OSD Setup
1st Level Menu 2nd/3rd Level Menu Description
Aspect
Auto
Auto adjusting the picture aspect ratio
16:9
Picture in 16:9 mode
4:3
Picture in 4:3 mode
Return
Returning to the previous menu
Exit
Exiting from this function menu
Input
HDMITM
Digital HDMITM signal input
D-Sub
Analog D-Sub signal input
Return
Returning to the previous menu
Exit
Exiting from this function menu
Adjust
Auto Adjust
Auto adjusting the horizontal/vertical position, clock and focus of pictures
Auto Color
Adjusting the white balance of pictures
Gamma
Gamma 1 Adjusting color tone brightness gray 1
Gamma 2 Adjusting color tone brightness gray 2
Return Returning to the previous menu
Exit
Exiting from this function menu
Return
Returning to the previous menu
Exit
Exiting from this function menu
Other
Language
(More languages coming soon)
English Deutsch
Language factory default is English.
Power Off
Return Exit ON
OFF
Return Exit
Returning to the previous menu
Exiting from this function menu
Turning off the monitor after saving power for 1 minute
Deactivating the timed switch-off function
Returning to the previous menu
Exiting from this function menu
OSD Setup 11
1st Level Menu 2nd/3rd Level Menu
Other
Reset
YES
NO
Return
Exit
OD
OFF
Normal
Extreme
ECO Mode
Return Exit ON
OFF
Return Exit Adaptive- ON Sync OFF Return Exit Return Exit Exit
Description
Resetting to the factory default settings
Exiting from the Reset function
Returning to the previous menu
Exiting from this function menu
Deactivating the response time overdrive function
Setting the monitor's response time to normal speed
Setting the monitor's response time to extreme speed
Returning to the previous menu
Exiting from this function menu
When ECO Mode is set to ON: · Brightness curve will be adjusted. · Mode and DCR will be grayed out.
When ECO Mode is set to OFF: · A warning message will be shown on the screen. · Users can set Brightness to higher value.
Returning to the previous menu
Exiting from this function menu
Activating Adaptive-Sync to prevent screen tearing
Deactivating Adaptive-Sync
Returning to the previous menu
Exiting from this function menu
Returning to the previous menu
Exiting from this function menu
Exiting from the OSD Setup
12 OSD Setup
Specifications
Monitor Size Curvature Panel Type Resolution Aspect Ratio Brightness (nits) Contrast Ratio Refresh Rate Response Time I/O
View Angles DCI-P3*/ sRGB Surface Treatment Display Colors Monitor Power Options Power Adapter Specs Power Input Power Output Adjustment (Tilt) Kensington Lock VESA Mounting
PRO MP241X 23.8 inch Flat VA 1920 x 1080 (FHD) 16:9
250 cd/m2 (TYP) 3000:1 75Hz 4ms (GTG) HDMITM Connector x1 D-Sub Port x1 178°(H) , 178°(V) 84% / 105% Anti-glare 16.7 Million 12V 2.5A Model: ADS-40NP-12-1 12030E 100~240V, 50~60Hz, 1.5A 12V 2.5A -5° ~ 15° Yes Plate Type: 75 x 75 mm Screw Type: M4 x 10 mm
· Thread Diameter: 4 mm · Thread Pitch: 0.7 mm · Thread Length: 10 mm
Specifications 13
Monitor
PRO MP241X
Dimension (W x H x D)
541.79 x 416.61 x 180.80 mm
Weight
2.85 Kg (Net) 4.27 Kg (Gross)
Environment
Operating
Temperature: 0 ~ 40 Humidity: 20% ~ 90%, non-condensing Altitude: 0 ~ 5000m
Storage
Temperature: -20 ~ 60 Humidity: 10% ~ 90%, non-condensing
* Based on CIE1976 test standards.
14 Specifications
Preset Display Modes
Standard
Resolution
VGA
640x480
@60Hz
@67Hz
@72Hz
@75Hz
Dos-Mode
720x480
@60Hz
720x576
@50Hz
SVGA
800x600
@56Hz
@60Hz
@72Hz
@75Hz
XGA
1024x768 @60Hz
@70Hz
@75Hz
SXGA
1280x1024 @60Hz
@75Hz
WXGA+
1440x900 @60Hz
WSXGA+ 1680x1050 @60Hz
Full HD
1920x1080 @60Hz
@75Hz
Video Timing Resolution
720P 1080P @60Hz
HDMITM V V V V V V V V V V V V V V V V V V V V V
D-Sub V V V V V V V V V V V V V V V V V V
V V
Preset Display Modes 15
Troubleshooting
The power LED is off.
· Press the monitor power button again. · Check if the monitor power cable is properly connected.
No image.
· Check if the computer graphics card is properly installed. · Check if the computer and monitor are connected to electrical outlets and are
turned on. · Check if the monitor signal cable is properly connected. · The computer may be in Standby mode. Press any key to activate the monitor.
The screen image is not properly sized or centered.
· Refer to Preset Display Modes to set the computer to a setting suitable for the monitor to display.
No Plug & Play.
· Check if the monitor power cable is properly connected. · Check if the monitor signal cable is properly connected. · Check if the computer and graphics card are Plug & Play compatible.
The icons, font or screen are fuzzy, blurry or have color problems.
· Avoid using any video extension cables. · Adjust brightness and contrast. · Adjust RGB color or tune color temperature. · Check if the monitor signal cable is properly connected. · Check for bent pins on the signal cable connector.
The monitor starts flickering or shows waves.
· Change the refresh rate to match the capabilities of your monitor. · Update your graphics card drivers. · Keep the monitor away from electrical devices that may cause electromagnetic
interference (EMI).
16 Troubleshooting
Safety Instructions
Read the safety instructions carefully and thoroughly.
All cautions and warnings on the device or User Guide should be noted.
Refer servicing to qualified personnel only.
Power
Make sure that the power voltage is within its safety range and has been adjusted properly to the value of 100~240V before connecting the device to the power outlet.
If the power cord comes with a 3-pin plug, do not disable the protective earth pin from the plug. The device must be connected to an earthed mains socket-outlet.
Please confirm the power distribution system in the installation site shall provide the circuit breaker rated 120/240V, 20A (maximum).
Always disconnect the power cord or switch the wall socket off if the device would be left unused for a certain time to achieve zero energy consumption.
Place the power cord in a way that people are unlikely to step on it. Do not place anything on the power cord.
If this device comes with an adapter, use only the MSI provided AC adapter approved for use with this device.
Battery
Please take special precautions if this device comes with a battery.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.
Avoid disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, which can result in an explosion.
Avoid leaving a battery in an extremely high temperature or extremely low air pressure environment that can result in an explosion or the leakage of flammable liquid or gas.
Do not ingest battery. If the coin/button cell battery is swallowed, it can cause severe internal burns and can lead to death. Keep new and used batteries away from children.
European Union:
Batteries, battery packs, and accumulators should not be disposed of as unsorted household waste. Please use the public collection system to return, recycle, or treat them in compliance with the local regulations.
BSMI:
For better environmental protection, waste batteries should be collected separately for recycling or special disposal.
Safety Instructions 17
California, USA: The button cell battery may contain perchlorate material and requires special handling when recycled or disposed of in California. For further information please visit: https://dtsc.ca.gov/perchlorate/
Environment
To reduce the possibility of heat-related injuries or of overheating the device, do not place the device on a soft, unsteady surface or obstruct its air ventilators.
Use this device only on a hard, flat and steady surface. To prevent the device from tipping over, secure the device to a desk, wall or fixed
object with an anti-tip fastener that helps to properly support the device and keep it safe in place. To prevent fire or shock hazard, keep this device away from humidity and high temperature. Do not leave the device in an unconditioned environment with a storage temperature above 60 or below -20, which may damage the device. The maximum operating temperature is around 40. When cleaning the device, be sure to remove the power plug. Use a piece of soft cloth rather than industrial chemical to clean the device. Never pour any liquid into the opening; that could damage the device or cause electric shock. Always keep strong magnetic or electrical objects away from the device. If any of the following situations arises, get the device checked by service personnel: · The power cord or plug is damaged. · Liquid has penetrated into the device. · The device has been exposed to moisture. · The device does not work well or you can not get it working according to the User
Guide. · The device has dropped and damaged. · The device has obvious sign of breakage.
18 Safety Instructions
TÜV Rheinland Certification
TÜV Rheinland Low Blue Light Certification
Blue light has been shown to cause eye fatigue and discomfort. MSI now offers monitors with TÜV Rheinland Low Blue Light certification to ensure users' eye comfort and well-being. Please follow the instructions below to reduce the symptoms from extended exposure to the screen and blue light. Place the screen 20 28 inches (50 70 cm) away from your eyes and a little below
eye level. Consciously blinking the eyes every now and then will help to reduce eye strain after
extended screen time. Take breaks for 20 minutes every 2 hours. Look away from the screen and gaze at a distant object for at least 20 seconds
during breaks. Make stretches to relieve body fatigue or pain during breaks. Turn on the optional Low Blue Light function.
TÜV Rheinland Flicker Free Certification
TÜV Rheinland has tested this product to ascertain whether the display produces visible and invisible flicker for the human eye and therefore strains the eyes of users.
TÜV Rheinland has defined a catalogue of tests, which sets out minimum standards at various frequency ranges. The test catalogue is based on internationally applicable standards or standards common within the industry and exceeds these requirements.
The product has been tested in the laboratory according to these criteria. The keyword "Flicker Free" confirms that the device has no visible and invisible
flicker defined in this standard within the range of 0 - 3000 Hz under various brightness settings. The display will not support Flicker Free when Anti Motion Blur/MPRT is enabled. (The availability of Anti Motion Blur/MPRT varies by products.)
TÜV Rheinland Certification 19
Regulatory Notices
CE Conformity
This device complies with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (2014/30/EU), Low-voltage Directive (2014/35/EU), ErP Directive (2009/125/EC) and RoHS directive (2011/65/EU). This product has been tested and found to comply with the harmonized standards for Information Technology Equipment published under Directives of Official Journal of the European Union.
FCC-B Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the measures listed below:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
Notice 1
The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Notice 2
Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
MSI Computer Corp.
901 Canada Court, City of Industry, CA 91748, USA
(626) 913-0828
www.msi.com
20 Regulatory Notices
WEEE Statement
Under the European Union ("EU") Directive on Waste Electrical and Electronic Equipment, Directive 2012/19/EU, products of "electrical and electronic equipment" cannot be discarded as municipal waste anymore and manufacturers of covered electronic equipment will be obligated to take back such products at the end of their useful life.
Chemical Substances Information
In compliance with chemical substances regulations, such as the EU REACH Regulation (Regulation EC No. 1907/2006 of the European Parliament and the Council), MSI provides the information of chemical substances in products at: https://csr.msi.com/global/index
RoHS Statement
Japan JIS C 0950 Material Declaration
A Japanese regulatory requirement, defined by specification JIS C 0950, mandates that manufacturers provide material declarations for certain categories of electronic products offered for sale after July 1, 2006. https://csr.msi.com/global/Japan-JIS-C-0950-Material-Declarations
India RoHS
This product complies with the "India E-waste (Management and Handling) Rule 2016" and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule.
Turkey EEE Regulation
Conforms to the EEE Regulations of the Republic Of Turkey
Ukraine Restriction of Hazardous Substances
The equipment complies with requirements of the Technical Regulation, approved by the Resolution of Cabinet of Ministry of Ukraine as of 10 March 2017, 139, in terms of restrictions for the use of certain dangerous substances in electrical and electronic equipment.
Vietnam RoHS
As from December 1, 2012, all products manufactured by MSI comply with Circular 30/2011/TT-BCT temporarily regulating the permitted limits for a number of hazardous substances in electronic and electric products.
Regulatory Notices 21
Green Product Features
Reduced energy consumption during use and stand-by Limited use of substances harmful to the environment and health Easily dismantled and recycled Reduced use of natural resources by encouraging recycling Extended product lifetime through easy upgrades Reduced solid waste production through take-back policy
Environmental Policy
The product has been designed to enable proper reuse of parts and recycling and should not be thrown away at its end of life.
Users should contact the local authorized point of collection for recycling and disposing of their end-of-life products.
Visit the MSI website and locate a nearby distributor for further recycling information.
Users may also reach us at gpcontdev@msi.com for information regarding proper disposal, take-back, recycling, and disassembly of MSI products.
Warning!
Overuse of screens is likely to affect eyesight.
Recommendations:
1. Take a 10-minute break for every 30 minutes of screen time. 2. Children under 2 years of age should have no screen time. For children aged 2
years and over, screen time should be limited to less than one hour per day.
Copyright and Trademarks Notice
Copyright © Micro-Star Int'l Co., Ltd. All rights reserved. The MSI logo used is a registered trademark of Micro-Star Int'l Co., Ltd. All other marks and names mentioned may be trademarks of their respective owners. No warranty as to accuracy or completeness is expressed or implied. MSI reserves the right to make changes to this document without prior notice.
The terms HDMITM, HDMITM High-Definition Multimedia Interface, HDMITM Trade dress and the HDMITM Logos are trademarks or registered trademarks of HDMITM Licensing Administrator, Inc.
Technical Support
If a problem arises with your product and no solution can be obtained from the user's manual, please contact your place of purchase or local distributor. Alternatively, please visit https://www.msi.com/support/ for further guidance.
22 Regulatory Notices