User Manual for Futaba models including: R7214SB-24G, AZPR7214SB-24G, AZPR7214SB24G, R7214SB FASSTest-2.4GHz Bidirectional Communication System, FASSTest-2.4GHz Bidirectional Communication System, Bidirectional Communication System, Communication System
Futaba Corporation R7214SB-24G RECEIVER AZPR7214SB-24G AZPR7214SB24G r7214sb 24g
The. R7214SB receiver features bi-directional communication with a FASSTest Futaba transmitter ... 7 Cycle the receiver power off and back on again after.
R7214SB 14-Channel (PWM) Air Receiver (26-Channel S.BUS) FASSTest – Futaba UK
File Info : application/pdf, 2 Pages, 2.34MB
DocumentDocumentFASSTest12CH(Telemetry OFFmode This mode is forcibly turning off telemetry transmission to prevent collision of telemetry signals from the receiver to the transmitter when using dual RX link mode in FASSTest12ch mode. 1 Turn on the receiver. [Transmitter is always OFF] 2 Press and hold the SW for 5 seconds or more. Blinking switches every 5 seconds as follows. RED ORANGE GREEN ORANGE slow blink 3 Release the switch here Blinks ORANGE once FASSTest12CH(Telemetry OFFmode : OFF Press SW once more to return to flashing orange once 4 Press switch FASSTest12CH(Telemetry Blinks ORANGE twice OFFmode : ON 5 Press and hold the SW Blinks ORANGE How to Dual Rx Link 1 Install two receivers on the aircraft as shown in the connection example. 2 Link the two receivers using the dual receiver feature of the transmitter. For systems without dual receiver capability, link each receiver in turn. Transmitter in link mode For FASSTest 18CH Select dual mode and link primary *Follow the link procedure for each receiver manual. Turn on the main Transmitter in link mode receiver and link For FASSTest 18CH Select dual mode and link secondary About telemetry system Turn on the sub receiver and link When using the dual receiver function The telemetry function of the main receiver can be used Sub-receiver telemetry function is not available Telemetry for FASSTest12CH In FASSTest12CH mode, after linking R7214SB in telemetry OFF mode, link the receiver you want telemetry to. (The transmitter will show the telemetry of the last linked transmitter.) 1 First Link R7214SB Telemetry OFF mode 2 Second Link R7214SB Telemetry 2 Display Change to this mode when using FASSTest12CH in dual RX link mode. 6 Release SW Solid ORANGE 1 First Link 2 Second Link R7214SB Telemetry OFF mode e.g. FASSTest receiver Telemetry 2 Display 7 Turn off the receiver power After restarting, the LINK LED lights up. In FASSTest12CH Telemetry OFF Mode Status LINK LED Start Orange Solid 2 Telemetry display of second-linked receiver. 1 Telemetry OFF first-Linked receiver. Compliance Information Statement (for U.S.A.) This device, trade name Futaba Corporation, model number R7214SB, complies with part15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION: To assure continued FCC compliance 1. Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. 2. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. The responsible party of this device compliance is: FUTABA Corporation of America 2681 Wall Triana Hwy Huntsville, AL 35824, U.S.A. Phone:1-256-461-9399 FAX:1-256-461-1059 E-mail: service@futabaUSA.com FUTABA CORPORATION Hobby Radio Control Business Center Sales & Marketing Department 1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan TEL: +81-475-32-6051, FAX: +81-475-32-2915 ©FUTABA CORPORATION 2023, 6 (1) 1M23N36204 R7214SB FASSTest-2.4GHz Bidirectional Communication System Dual Rx Link System Equipment S.BUS2 / S.BUS Port and 14 Channels for Conventional System Receiver Applicable systems: Futaba FASSTest-2.4GHz system transmitter Thank you for purchasing a Futaba R7214SB FASSTest-2.4GHz compatible receiver. The R7214SB receiver features bi-directional communication with a FASSTest Futaba transmitter using the S.BUS2 port. Using the S.BUS2 port an impressive array of telemetry sensors may be utilized. It also includes both standard PWM output ports (1-14ch) and S.BUS output ports. The R7214SB can also be switched to the Dual Rx Link System. This system can ensure safety by mounting two FASSTest receivers on one aircraft. Usage precaution · Analog servos cannot be used with the R7214SB in the FASSTest 12CH mode. · Don't connect to Extra Voltage before turning on a receiver. WARNING Changes or modification not approved by the party responsible for compliance could void the user's authority to operate the equipment. The R7214SB receiver should be protected from vibration by foam rubber, Velcro, or similar mounting methods. Protect from moisture. Keep away from conductive materials to avoid short circuits. Antenna installation precaution Do not cut or bundle the receiver antenna wire. The antennas must be mounted in such a way to assure they are strain relieved. Keep the antenna as far away from the motor, ESC and other noise sources as you possibly can. Do not touch the antenna to metal, carbon, or other conductive material. Be sure that the two antennas are placed at 90 degrees to each other. The R7214SB has two antennas. In order to maximize signal reception and promote safe modeling Futaba has adopted a diversity antenna system. This allows the receiver to obtain RF signals on both antennas and fly problem-free. Antenna installation for carbon fuselage You must leave 30mm at the tip of the antenna fully exposed. The exposed antenna should be secured so that it cannot move around or back inside of your aircraft. Be careful of connector insertion Don't connect an S.BUS servo / gyro to S.BUS2 connector. Link precaution Do not perform the linking procedure while the motor's main power is connected or the engine is operating as it may result in serious injury. When the linking is complete, please cycle the receiver power and ensure the receiver is properly linked to the transmitter. Power on the system in this order: Transmitter first, followed by the receiver. If the R7214SB receiver was previously linked to another transmitter, make sure that transmitter is not operating while linking the receiver to the new transmitter. Connector precaution Don't connect a connector, as shown in this figure. It will short-circuit, if it connected in this way. A short circuit across the battery terminals may cause abnormal heating, fire and burns. DANGER Receiver Do not insert either a switch or battery in this manner. (Typical installation) When all ports are used. Servo for conventional system HUB *Be sure that when using ESCs regulated output the capacity of the ESC must meet your usage condition. *Never use dry batteries for the power supply of the R7214SB as they may cause difficulties. Servo Battery 3.7 7.4 V Antenna Switch A battery is connectable also with which port. Channel 1 output Channel 12 output R7214SB Specifications Extra Voltage Port It connects with the battery for power, etc. External voltage input cable of an option is used. The voltage of the battery can be displayed with a transmitter. S.BUS port (SB/DG2 Mode LED S.BUS2 port Link LED Mode switch (SB2/RX (SB2/DG1) (It is not used for a link.) FASSTest-2.4 GHz system(18 ch/12 ch mode) S.BUS2 and S.BUS port and 14 channels for conventional system receiver · Dual antenna diversity · Size: 1.46 x 1.98 x 0.63 in. (37.0 x 50.2 x 15.9 mm) · Weight: 0.73 oz. (20.8 g) · Power requirement: 3.7 V to 7.4 V(Voltage range: 3.5 V to 8.4 V) · Battery F/S Voltage: It sets up with a transmitter · Extra Voltage port: 0 70 V DC Port can be changed (Refer to separate table) HUB Percentage of Waste Paper pulp 80% HUB HUB HUB HUB S.BUS Servo S.BUS Gyro Temperature Sensor Voltage Sensor Current Sensor RPM Sensor Altitude Sensor Airspeed Sensor S.BUS2 Tool LED Indication Status No signal reception Receiving signals Waiting for link Unrecoverable error (EEPROM, etc.) LINK LED Red Solid Green Solid Start 2second later Red Blink 3 second Red Green Alternate blink In Dual RX Link Mode Status MODE LED External receiver is receiving error or not connected. S.BUS signal not received S.BUS signal reception from external receiver (also received by external receiver) Red Solid Green Solid In FASSTest12CH Telemetry OFF Mode Status Start LINK LED Orange Solid Link FASSTest is a bidirectional communication system between the R7214SB receiver and FASSTest capable transmitters. Multiple optional telemetry sensors may be connected to the S.BUS2 on the receiver and that data is in turn displayed on the transmitter. Link to the transmitter 1 Bring the transmitter and the receiver close to each other, within 20 inches (half meter). 2 Turn on the transmitter. Place the transmitter into the receiver linking mode. 3 Turn on the receiver. 4 The receiver will wait for the linking process to begin for 2 seconds. Following that it will return to the normal operation mode. 5 When the LED of the receiver changes from blinking red to solid green, linking is complete. (A link waiting state is ended in 3 second.) · Refer to the transmitter's operation manual for complete details on how to place the transmitter into the linking mode. · If there are many FASSTest systems turned on in close proximity, your receiver might have difficulty establishing a link to your transmitter. This is a rare occurrence. However, should another FASSTest transmitter/receiver be linking at the same time, your receiver could link to the wrong transmitter. This is very dangerous if not noticed. To avoid the problem, we strongly recommend that you double check whether your receiver is really under control by your transmitter. · If the System Type of the transmitter is changed, the receiver will need to be re-linked to the transmitter. S.BUS2 S.BUS2 extends S.BUS and supports bidirectional communication. Sensors are connected to the S.BUS2 port. Compliance Information Statement (for Canada) This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. French: Cet appareil radio est conforme au CNR-210 d'Industrie Canada. L'utilisation de ce dispositifest autorisée seulement aux deux conditions suivantes : (1) il ne doit pas produire de brouillage, et (2) l'utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même sice brouillage est susceptible de compromettre le fonctionnement du dispositif. Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Antenna installation Do not bend the antenna part 90° Gently bend the coaxial cable part. Antenna should be secured so that it cannot move around or back inside of aircraft. Coaxial cable Antenna part Channel Modes The R7214SB is capable of changing its channel allocations as described in the table below. This is especially important when using the receiver in a dual receiver mode. See your transmitter operation manual for complete details on operating in the dual receiver mode. R7214SB CH Mode table Mode A Mode B Mode C Mode D Mode E Mode F Mode G Mode H 1 1 1 1 1 13 13 13 13 2 2 2 2 2 14 14 14 14 3 3 3 3 3 15 15 15 15 4 4 4 4 4 16 16 16 16 5 5 5 5 5 17 17 17 17 6 6 6 6 6 18 18 18 18 7 7 7 7 7 19 19 19 19 8 8 8 8 8 20 20 20 20 9 9 9 9 9 21 21 21 21 10 10 10 10 10 22 22 22 22 11 11 11 11 11 23 23 23 23 12 12 12 12 12 24 24 24 24 SB2/DG1 DG1 SB2 DG1 SB2 DG1 SB2 DG1 SB2 SB/DG2 DG2 SB SB DG2 DG2 SB SB DG2 LED RED 1 RED 2 RED 3 RED 4 RED 5 GREEN1 GREEN2 GREEN3 Default 1 Turn on the receiver. [Transmitter is always OFF] 2 Press and hold the SW for 5 seconds to 10 seconds. 3 When the LED of the receiver changes from blinking red to blinking orange, SW is released. 4 The LED should now blink red two times in the patterns described in the chart below. 5 Each press of the SW advances the receiver to the next mode. 6 When you reach the mode that you wish to operate in, press and hold the SW for more than 2 seconds. When LED blinks in orange, it is the completion of a mode change, SW is released. 7 Cycle the receiver power off and back on again after changing the Channel mode. 1 Turn on the receiver. [Transmitter is always OFF] LINK LED Red Solid 2 Receiver enters link waiting state Start 2second later Red Blink 3 second 3 The LED will flash for the current CH Current CH mode output mode. display Dual Rx Link System By installing two receivers in one aircraft, if one receiver becomes unable to communicate, the other receiver can be operated. How to change to Dual RX Link mode 1 Turn on the receiver. [Transmitter is always OFF] 2 Press and hold the SW for 5 seconds or more. Receiver : A Receiver : B Communicate with two receivers Even if there is a problem with the B receiver, communication will be performed with the A receiver. Even if there is a problem with the A receiver, communication will be performed with the B receiver. In Dual RX link mode, the SB2/RX port is for reception only, so use separate ports for S.BUS output and S.BUS2 input/output. Connection example R7214SB Blinking switches every 5 seconds as follows. RED ORANGE GREEN ORANGE slow blink 3 Release the switch here Blinks GREEN once If it is passed, turn off the power and restart Dual RX Link mode : OFF Press SW once more to return to flashing green once 4 Press switch Blinks GREEN twice Dual RX Link mode : ON 5 Press and hold the SW Blinks ORANGE FASSTest Receiver S.BUS2 ESC When using ESC Declaration of Conformity (for EU) Hereby, Futaba Corporation declares that the radio equipment type is R7214SB in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.rc.futaba.co.jp/support/manual/ 6 Release SW Solid ORANGE 7 Turn off the receiver power After restarting, the MODE LED lights up. Status External receiver is receiving error or not connected. S.BUS signal not received S.BUS signal reception from external receiver (also received by external receiver) MODE LED Red Solid Green Solid