User Guide for LEAB models including: 1051009024 CAN-LIN Gateway, 1051009024, CAN-LIN Gateway, Gateway
1 Safety This Quick Start Guide is intended to support safe handling of the CAN-LIN Gateway. Observe the safety instructions: WARNING! Risk of injury from electric shock.
CAN-LIN Gateway Quick start guide 27/10/2023 V 2 1 Safety This Quick Start Guide is intended to support safe handling of the CAN-LIN Gateway. Observe the safety instructions: WARNING! Risk of injury from electric shock. Disconnect the vehicle negative cable prior to Installation. WARNING! Fire hazard due to short circuit: Secure your vehicle with an additional fuse installed near the unit. NOTE! Penetrating water can damage the unit: Prevent water from entering the housing during cleaning. NOTE! The unit is designed for interior use only. Do not mount the unit outside the vehicle. NOTE! Installation must only be carried out by qualified electricians. 2 About this product The CAN-LIN Gateway provides the most important data of the LPS II on the CI bus and therefore allows the LPS II to be integrated into a CI bus on-board management system. In addition to information on current, voltage and power for solar, vehicle power circuit and external feed, the charging status of the LPS II is provided on the CI bus. In the same way, the 230 V/12 V output as well as the jump-start function of the LPS II can be switched on and off. 3 Package contents No. Name 1x CAN-LIN Gateway 1x Quick start guide 4 Accessories (optional) CAN-LIN Gateway connection cable to LPS II Part number 1601001136 Cable length: 5 m Connections: open cable end on M12 connector 5 Technical specifications Part number Power consumption Voltage range Temperature range Protection class Housing BUS system connections Dimensions (L x W x H) Weight CAN-LIN Gateway 1051009024 18 mA 9.8 V ... 14.6 V DC: -20 °C ... +75 °C III 7-pin relay socket housing CAN bus/LIN bus 60 mm x 30 mm x 30 mm 30 g 6 LIN bus parameters The following commands and information can be transmitted or controlled via the LIN bus system: Information Command 12 V/230 V input current Capacity:12 V/230 V/solar Switch 12 V/230 V output on/ off 12 V/230 V output current Operating status Switch emergency start function on/off 12 V/230 V input voltage Error levels 12 V/230 V output voltage Error codes Solar power Firmware version Solar voltage Hardware version Battery temperature Serial number Battery current Residual time IO signals Residual capacity SoC (State of Charge) 7 PIN assignment CAN-LIN Gateway Pin Assignment Description 1 Terminal 31 Ground (earth) 2 CAN (High) CAN-Bus High 3 LIN LIN bus 4 Terminal 31 Ground 5 CAN (Low) CAN-Bus Low 6 n. a. Not assigned 8 Terminal 30 12 V DC: M12 connector of the connection cable (accessories) PIN Assignment 1 Not assigned 2 Battery positive 3 GND 4 CAN (High) 5 CAN (Low) Description 12 V DC: Ground CAN-Bus High CAN-Bus Low Core colour Black Brown Blue Grey 8 Installation To install the unit, proceed as follows: NOTE! To ensure the smooth operation of the CAN-LIN Gateway, make sure that the Gateway and the LPS II are at the same ground potential (GND). ü A 5-pin M12 connector is available. 1. Connect pin 3 (LIN) of the gateway to the LIN connection point of the CI bus. 2. Connect pin 2 (CAN (High)) of the gateway to pin 4 of the M12 connector. 3. Connect pin 5 (CAN (Low)) of the gateway to pin 5 of the M12 connector. 4. Connect pin 8 (12 V DC) of the gateway to pin 2 of the M12 connector or the 12 V connec- tion point of your vehicle. 5. Connect pin 1 or pin 4 (GND) of the gateway to pin 3 of the M12 connector or the ground of your vehicle. 6. Connect the M12 plug to the remote connector of the LPS II. ð The unit is installed. 9 Disposal Dispose of the device in accordance with the Waste Electrical and Electronic Equipment Regulations (WEEE). The system must not be disposed of with household waste. Take it to a recycling point or return it to your point of sale. LEAB Automotive GmbH Thorshammer 6 24866 Busdorf info@leab.eu +49 (0) 4621 - 97860-0ST4 PDF Engine (Build 13.0.1.0) SCHEMA ST4