mailto:service@etcasia.com
mailto:service@etcconnect.com
mailto:service@etceurope.com
ETC - Theatre, Film, Studio and Architectural Lighting
User Guide for ETC models including: ETCpad Portable Access Device, ETCpad, Portable Access Device, Access Device
ETCpad Handbuch - Preworks
ETC ETCpad wired/wireless tablet - Lillehammer Tekniske Byrå AS
File Info : application/pdf, 10 Pages, 1.04MB
DocumentDocumentETC Setup Guide ETCpad Overview The ETCpad provides wireless and/or wired access to ETC applications. Note: The device may only be used with ETC applications . Other apps may not be installed. ETCpad ships with the following: · Power Supply · Network Adapter · USB Hub with USB-C Adapter · Hand Strap · Eos Augment3d Target Set Note: The Eos Augment3d Target Set is for use with the Focus Wand feature of aRFR . This functionality will be enabled in a future update. ETCpad USB-C connector Front Right Rear Power switch Network jack Network adapter Volume control Docking port Battery compartment Audio jack WARNING: This device contains a lithium battery. Battery may explode if mistreated. Do not disassemble or dispose of in fire. Corporate Headquarters Middleton, WI, USA Tel +608 831 4116 Service: (Americas) service@etcconnect.com London, UK Tel +44 (0)20 8896 1000 Service: (UK) service@etceurope.com Rome, IT Tel +39 (06) 32 111 683 Service: (UK) service@etceurope.com Holzkirchen, DE Tel +49 (80 24) 47 00-0 Service: (DE) techserv-hoki@etcconnect.com Hong Kong Tel +852 2799 1220 Service: (Asia) service@etcasia.com Web: etcconnect.com © 2023 Electronic Theatre Controls, Inc. Product information and specifications subject to change. ETC intends this document to be provided in its entirety. 4250M2270 Rev E Released 2023-MM ETC Setup Guide ETCpad Home Screen When ETCpad starts up, it will display the home screen. Battery Indicator Time Back Home Overview The home screen displays the icons for any ETC applications installed, settings for the ETCpad, and application update. Any notifications will display near the bottom of the display. There are three navigation buttons located at the bottom of the display: · Back - opens the last screen that you were on. · Home - opens the home screen. · Overview - opens a list of recently viewed apps. To open a app, tap on its image. To close an app, swipe its image either to the left or right. ETCpad Page 2 of 10 ETC ETC Setup Guide ETCpad Settings Tap on the Settings icon to open the settings display, which shows all the available settings options for the ETCpad. About This display shows information about the ETCpad device, such as the device's software and current IP address. Note: The About display does not show information about the currently installed ETC applications. Please see the individual application's About display for app specific information. Auto Launch Options This display allows you to select an app to open immediately when ETCpad is powered on. Tap the box to select the desired app. Battery This display shows the current battery charge percentage, approximate battery life left, and usage by application since last charge. While in this display, the battery data does not automatically refresh. To see the most current information, press Refresh. ETCpad Page 3 of 10 ETC ETC Setup Guide ETCpad Date & Time This display allows you to set the date and time for your device. The following settings are available: · Automatic Date & Time - automatically sets the date and time based on the network-provided information. Enabled by default. · Automatic Time Zone - automatically sets the time zone based on the network-provided information. Enabled by default. · Set Date - opens a calendar to allow you to manually set the current date. Automatic Date & Time must be disabled first. · Set Time - opens a clock to allow you to manually set the current time. Automatic Date & Time must be disabled first. · Select Time Zone - opens a list of available time zones. Automatic Time Zone must be disabled first. · Use 24-Hour Format - displays the time in a 24-hour format as HH : MM. Enabled by default. When disabled, time will display in the 12-hour format (AM/PM). Display In this area, you can adjust the display settings. The following settings are available: · Brightness Level - adjusts the backlight for the display. · Adaptive Brightness - when enabled, the device will automatically adjust the backlight based on external lighting conditions. · Sleep - allows you to set the period of inactivity before the device will go into sleep mode. · Lock Screen Rotation - allows you to lock the screen to either portrait or landscape based off of its current orientation. · Large Text - when enabled, the text on the device will display in a larger font. This setting does not affect the installed applications. Manage Apps ETCpad This menu allows you to enable or disable individual apps installed on the ETCpad. Disabling an app removes the icon from the home screen but does not uninstall the app. If an app is disabled, a popup will appear asking for confirmation. Page 4 of 10 ETC ETC Setup Guide ETCpad Reset This display allows you to either reset the network settings or restore the device to factory settings. Set Connection Type This option allows you to set the network connection type to either ethernet or WiFi. Note: You can only select one connection type at a time. Ethernet In this display, you can configure the device to connect via ethernet by using the network adapter. The IP settings can be set to either Static (you provide the IP address) or DHCP (IP address is automatically obtained from a DHCP server). If Static is selected, you will need to provide the IP Address, Subnet Mask, and Default Gateway. WiFi In this display, you can select an available WiFi network to connect to when WiFi is turned on. Tapping an available network will give you the options to connect to it, forget the network, or cancel out of this option. If you tap a connected network, you will have the options to forget the network or cancel out of this option. Add Hidden Network In this display, you can add a WiFi network with a non-broadcasting (hidden) SSID (System Set Identifier). To add, you will need to enter the SSID, Security type, and IP Settings. The IP settings can be set to either Static (you provide the IP address) or DHCP (IP address is automatically obtained from a DHCP server). Once entered, tap Add Network to create. ETCpad Page 5 of 10 ETC ETC Setup Guide ETCpad Updating Apps via UpdaterAtor Note: Updating ETCpad apps via UpdaterAtor requires UpdaterAtor v6.X or later and ETCpad v2.0 or later. If your ETCpad is running a version prior to 2.0, contact ETC Technical Services to request an Image Upgrade Kit. ETCpad apps can be updated via a networked connection to the UpdaterAtor software. While a WiFi or an Ethernet connection will work, Ethernet is recommended. Once connected, select Software Version > Manage. A popup will appear showing information for apps currently installed on the ETCpad. Select Update for any individual apps that need to be updated. ETCpad Page 6 of 10 ETC ETC Setup Guide ETCpad Accessories The following accessories are available for use with your ETCpad: · Network Adapter · USB Hub with USB-C Adapter · Hand Strap · Shoulder Strap · Replacement Batteries · VESA Base · Office Base · Stylus (enabled in a future update) · MultiTablet Charger (charges up to 6 tablets) Note: For a list of which accessories ship with ETCpad, please see Overview on page 1. ETCpad Page 7 of 10 ETC ETC Setup Guide ETCpad Network Adapter A network adapter is provided with the ETCpad for wired ethernet connection. Installing the Network Adapter 1: Remove the four foam screw covers. 2: Remove the four screws using #1 Phillips screwdriver. You will need these screws to attach the adapter. 3: Put the adapter in place. 4: Using the screws from step 2, attach the network adapter. USB Hub The USB hub has three USB, one SD, and one MicroSD ports, and comes with a USB-C adapter. The hub is used for software installation. For information about software installation on the ETCpad, please see the current ETCpad Release Note. Hand and Shoulder Straps There are four connection points on the back of the ETCpad for connecting either a hand or shoulder strap. The hand strap is attached on a diagonal for either left or right hand use. The shoulder strap is attached on a horizontal line between two connection points. Hand Strap Placement Options Shoulder Strap Placement Options Installing the Strap 1: Remove the foam screw covers from two of the attachment points. 2: Remove the screws using #1 Phillips screwdriver. 3: Begin to screw in two of the screws included with your strap using a 2mm Allen wrench. 4: Slide the ends of the strap onto the screws and snap into place. 5: Tighten the screws down fully. You may experience some resistance due to the thread locker patch on the screw. 6: The strap can be adjusted by opening the hook and loop clasp and moving the position of the strap. Multitablet Charger We recommend not leaving ETCpad on the multitablet charger for long term storage. Instead, remove the battery from the device to reduce self-discharge of the battery. This will help maintain the current charge level in the battery for the next use. ETCpad Page 8 of 10 ETC ETC Setup Guide ETCpad Replacement Batteries Additional batteries are available for use as spares or replacements. Note: You can check the charge of your battery without turning the device on by pressing on the Battery Charge Indicator. You will need to remove the battery compartment cover to view the indicator. Replacing the Battery Battery Pull Tab Battery Charge Indicator Side Clip Side Clip Battery Tab Battery Tab 1: Carefully lift up on the battery compartment cover using your finger or a small screwdriver to remove it. 2: Gently pull up on the battery pull tab while releasing the side clips one at a time. 3: Lift battery out of compartment. 4: Place bottom two tabs of the new battery into place. 5: Push down gently on the battery to snap it into place. 6: Replace the battery compartment cover. ETCpad Page 9 of 10 ETC ETC Setup Guide ETCpad VESA and Office Bases The VESA and Office bases allow for horizontal docking of the ETCpad. Power Switch VESA Base Office Base The following ports are available on both docks: Power USB Ports Connector RS232 Reserved For Future Implementation Ethernet Port Note: Use only one network connection type at a time. If using ethernet while docked, you will need to use the dock's ethernet port and not the network adapter on the device. Stylus Stylus functionality will be enabled in a future software update. ETCpad Page 10 of 10 ETC