User Manual for BAFANG models including: DP C11 LCD Maxtix Display, DP C11, LCD Maxtix Display, Maxtix Display, Display
BAFANG | Service |
File Info : application/pdf, 16 Pages, 1.26MB
DocumentDocument7 USER MANUAL FOR DP C11.CAN USER MANUAL FOR DISPLAY CONTENT 7.1 Important Notice 2 7.6.3 Selection mode 5 7.2 Introduction of Display 2 7.6.4 Headlights / backlighting 6 7.3 Product Description 3 7.6.5 Walk Assistance 6 7.3.1 Specifications 3 7.6.6 SERVICE 7 7.3.2 Functions Overview 3 7.6.7 Battery capacity indication 7 7.4 Display 4 7.7 Settings 8 7.5 Key Definition 4 7.7.1 "Display Setting" 8 7.6 Normal Operation 5 7.7.2 "Information" 11 7.6.1 Switching the System ON/OFF 5 7.8 Error Code Definition 14 7.6.2 Selection of Support Levels 5 BF-UM-C-DP C11-EN November 2019 1 7.1 IMPORTANT NOTICE · If the error information from the display cannot be corrected according to the instructions, please contact your retailer. · The product is designed to be waterproof. It is highly recommended to avoid submerging the display under water. · Do not clean the display with a steam jet, high-pressure cleaner or water hose. · Please use this product with care. · Do not use thinners or other solvents to clean the display. Such substances can damage the surfaces. · Warranty is not included due to wear and normal use and aging. 7.2 INTRODUCTION OF DISPLAY · Model: DP C11.CAN BUS · The housing material is PC and Acrylic, and the button material is made of silicone. · The label marking is as follows: Note: Please keep the QR code label attached to the display cable. The information from the Label is used for a later possible software update. 2 BF-UM-C-DP C11-EN November 2019 USER MANUAL FOR DISPLAY 7.3 PRODUCT DESCRIPTION 7.3.1 Specifications · Operating temperature: -20~45 · Storage temperature: -20~50 · Waterproof: IP65 · Storage room Humidity: 30%-70% RH 7.3.2 Functional Overview · Speed display (including top speed and average speed, switching between km and miles) · Battery capacity indicator · Lighting control · Brightness setting for backlight · Walk assistance · Indication of performance support · Motor output power indicator · Time display for single journeys · Kilometer stand (including single-trip dis- tance, total distance and remaining distance) · Setting the support levels · Energy consumption indicator CALORIES (Note: If the display has this function) · Display for the remaining distance (Depends on your riding style) · Information View (battery, controller, HMI and sensor) · Error messages view BF-UM-C-DP C11-EN November 2019 3 7.4 DISPLAY 1 Display of battery capacity in real time. 3 2 Support level 1 4 5 3 The display shows this symbol , When 2 the lights are turned on. 6 4 Unit of speed 5 Digital speed display 6 Trip: Daily kilometers (TRIP) - Total kilometers (ODO) - Top speed (MAX) - Average speed (AVG) - Rremaining distance (RANGE) - Energy Consumption (CALORIES) - Output power (POWER)- Travel time (TIME). Service: Please see the service section 7.5 KEY DEFINITION up down System On/Off up down 4 BF-UM-C-DP C11-EN November 2019 USER MANUAL FOR DISPLAY 7.6 NORMAL OPERATION 7.6.1 Switching the System ON/OFF Press and hold off the system. (>2S) on the display to turn on the system. Press and hold (>2S) again to turn If the "automatic shutdown time" is set to 5 minutes (it can be reset with the "Auto Off" function, See "Auto Off"), the display will automatically be turned off within the desired time when it is not in operation.If the password function is enabled, you must enter the correct password to use the system. 7.6.2 Selection of Support Levels When the display is turned on, press the or button (<0.5S) to switch to the support level, the lowest level is 0, the highest level is 5. When the system is switched on, the support level starts in level 1. There is no support at level 0. For different assist levels please see part "Assist Mode". 7.6.3 Selection mode Briefly press the button (<0.5s) to see the different trip modes. Trip: daily kilometers (TRIP) - total kilometers (ODO) - Maximum speed (MAX) - Average speed (AVG) - Rremaining distance (RANGE) - Energy consumption (CALORIES) - Output power (POWER) - Travel time (TIME). BF-UM-C-DP C11-EN November 2019 5 7.6.4 Headlights / backlighting Hold the button (>2S) to activate the headlight and taillights. Hold the button (>2S) again to turn off the headlight. The brightness of the backlight can be set in the display settings "Brightness". 7.6.5 Walk Assistance The Walk assistance can only be activated with a standing pedelec. Activation: Press the button until this symbol appears. Next press and hold down the button whilst the symbol is displayed, now the Walk assistance will activate. The symbol will blink and the pedelec moves approx. 5 km/h. After releasing the button, the motor stops automatically and switches back to level 0. 6 BF-UM-C-DP C11-EN November 2019 USER MANUAL FOR DISPLAY 7.6.6 SERVICE The display shows "SERVICE" as soon as a certain number of kilometers or battery charges has been reached. With a mileage of more than 5000 km (or 100 charge cycles), the "SERVICE" function is displayed on the display. Every 5000 km the display "SERVICE" is displayed every time. This function can be set in the display settings. 7.6.7 Battery capacity indicator The battery capacity is shown in the top left of the display. Each full bar represents a remaining capacity of the battery in a percentage. (as shown in the diagram below): Capacity Range 80%-100% 60%-80% 40%-60% 20%-40% 5%-20% <5% Indicator blinking BF-UM-C-DP C11-EN November 2019 7 7.7 SETTINGS After the display is turned on, press and hold the and buttons (at the same time) to enter into the setting menu, By pressing the or button (<0.5S), you can highlight and select Display Setting, Information or Exit. Then press the button (<0.5S) to confirm your selected option. Or highlight "EXIT" and press the button (<0.5S) to return to the main menu, or highlight "BACK" and press (<0.5S) the button (<0.5S) to return to the Settings interface. 7.7.1 "Display Setting" Press the or button (<0.5S) and highlight Display Setting, and then briefly press the (<0.5S) to access the following selections. button 7.7.1.1 "TRIP Reset" Reset mileage Press the or button (<0.5S) to highlight "Trip Reset" in the Display setting menu, and then press button (<0.5S) to select. Then with the or button choose between "YES" or "NO". Once you have chosen your desired selection, press the button (<0.5S) to save and exit to the "Display setting". 8 BF-UM-C-DP C11-EN November 2019 USER MANUAL FOR DISPLAY 7.7.1.2 "Unit" Selections in km/Miles Press the or button (<0.5S) to highlight "Unit" in the Display setting menu, and then press button (<0.5S) to select. Then with the or button choose between "Metric" (kilometer) or "Imperial" (Miles). Once you have chosen your desired selection, press the button (<0.5S) to save and exit to the "Display setting". 7.7.1.3 "Brightness" Display brightness Press the or button (<0.5S) to highlight "Brightness" in the Display setting menu, and then press button (<0.5S) to select. Then with the or button choose between "100%" / "75%" / "50%" /" 30%"/"10%". Once you have chosen your desired selection, press the button (<0.5S) to save and exit to the "Display setting". 7.7.1.4 "Auto Off" Set Automatic system switch off time Press the or button (<0.5S) to highlight "Auto Off" in the Display setting menu, and then press button (<0.5S) to select. Then with the or button choose between "OFF", "9"/"8"/"7"/"6"/ "5"/ "4"/"3"/"2"/"1", (The numbers are measured in minutes). Once you have chosen your desired selection, press the button (<0.5S) to save and exit to the "Display setting". BF-UM-C-DP C11-EN November 2019 9 7.7.1.5 "Assist Mode" Set support level Press the or button (<0.5S) to highlight "Max Pass" in the Display setting menu, and then press button (<0.5S) to select. Then with the or button choose between "3/5/9" (the amount of support levels). Once you have chosen your desired selection, press the button (<0.5S) to save and exit to the "Display setting". 7.7.1.6 "Service" Switching the notification on and off Press the or button (<0.5S) to highlight "Service" in the Display setting menu, and then press button (<0.5S) to select. Then with the or button choose between "NO" or "YES". Once you have chosen your desired selection, press the button (<0.5S) to save and exit to the "Display setting". 10 BF-UM-C-DP C11-EN November 2019 USER MANUAL FOR DISPLAY 7.7.2 "Information" Once the display is turned on, press and hold the and buttons (at the same time) to enter into the setting menu, press the or button (<0.5S) to select "Information", then press the button (<0.5S) to confirm and enter into "Information". 7.7.2.1 Wheel Size Press the or button (<0.5S) to highlight "Wheel Size", then press the button (<0.5S) to confirm and view the wheel size. To return, press the button (<0.5S) to exit back to the "Information". This information cannot be changed, this is only for information, about the pedelec. 7.7.2.2 Speed Limit Press the or button (<0.5S) to highlight "Speed Limit", then press the button (<0.5S) to confirm and view the speed limit. To return, press the button (<0.5S) to exit back to the "Information". This information cannot be changed, this is only for information, about the pedelec. BF-UM-C-DP C11-EN November 2019 11 7.7.2.3 Battery Information Press the or button (<0.5S) to highlight "Battery Info", then press the confirm. Now press the or button (<0.5S) to view the contents. To return, press the button (<0.5S) to exit back to the "Information". button (<0.5S) to Code Code definition unit Code Code definition unit Hardware ver Hardware version b10 Absolute SOC % Software ver Software version b11 Cycle times b01 Current temperature b12 Maximum not charging time Hour Recently not char- b04 Total voltage mV b13 ging time Hour b06 Average current mA d00 Number of battery cell b07 Remaining capacity mAh d01 Voltage of cell 1 mV b08 Full charge capacity mAh d02 Voltage of cell 2 mV b09 Relative SOC % dn Voltage of cell n mV NOTE: If no data is detected, "--" is displayed. 7.7.2.4 Controller Information Press the or button (<0.5S) to highlight "Ctrl Info", then press the button (<0.5S) to confirm. Now press the or button (<0.5S) to view Hardware Version or Software Version. To return, press the button (<0.5S) to exit back to the "Information". 12 BF-UM-C-DP C11-EN November 2019 USER MANUAL FOR DISPLAY 7.7.2.5 Display Information Press the or button (<0.5S) to highlight "Display Info", then press the button (<0.5S) to confirm. Now press the or button (<0.5S) to view Hardware Version or Software Version. To return, press the button (<0.5S) to exit back to the "Information". 7.7.2.6 Torque Information Press the or button (<0.5S) to highlight "Torque Info", then press the button (<0.5S) to confirm. Now press the or button (<0.5S) to view Hardware Version or Software Version. To return, press the button (<0.5S) to exit back to the "Information". 7.7.2.7 Error Code Press the or button (<0.5S) to highlight "Error code", then press the button (<0.5S) to confirm. Now press the or button (<0.5S) to view a list of error codes from the pedelec. It can show information for the last ten errors of the pedelec. The error code "00"means that there is no error. To return, press the button (<0.5S) to exit back to the "Information". BF-UM-C-DP C11-EN November 2019 13 7.8 ERROR CODE DEFINITION The display can show the errors of a pedelec. If an error is detected, one of the following error codes will be displayed. Note: Please read the description of the error code carefully. If you see the error code, restart the system first. If the problem is not resolved, please contact your dealer. Error Declaration Troubleshooting 04 The throttle has fault. 1. Check the connector of throttle whether they are correctly connected. 2. Disconnect the throttle, If the problem still occurs, please contact your retailer. (only with this function) Check the throttle can adjust back into its 05 The throttle is not back in its correct correct position, if the situation does not position. improve, please change to a new throttle.(only with this function) 07 Overvoltage protection 1. Remove the battery. 2. Re-Insert the battery. 3. If the problem persists, please contact your retailer. 08 Error with the hall sensor signal inside the motor Please contact your retailer. 09 Error with the Engine phase's Please contact your retailer. 1. Turn off the system and allow the Pedelec The temperature inside the engine to cool down. 10 has reached its maximum protection value 2. If the problem persists, please contact your retailer. The temperature sensor inside the 11 motor has an error Please contact your retailer. Error with the current sensor in the 12 Please contact your retailer. controller 13 Error with the temperature sensor inside of the battery Please contact your retailer. 14 BF-UM-C-DP C11-EN November 2019 USER MANUAL FOR DISPLAY Error Declaration Troubleshooting 1. Turn off the system and let the pedelec cool The protection temperature inside down. 14 the controller has reached its maxi- mum protection value 2. If the problem persists, please contact your retailer. 15 Error with the temperature sensor Please contact your retailer. inside the controller 21 Speed sensor Error 1. Restart the system 2. Check that the magnet attached to the spoke is aligned with the speed sensor and that the distance is between 10 mm and 20 mm. 3. Check that the speed sensor connector is connected correctly. 4. If the error persists, please contact your retailer. 25 Torque signal Error 1. Check that all connections are connected correctly. 2. If the error persists, please contact your retailer. 1.Check the connector from the speed sensor to make sure it is connected correctly. 26 Speed signal of the torque sensor has 2.Check the speed sensor for signs of damage. an error 3.If the problem persists, please contact your retailer. 27 Overcurrent from controller Please contact your retailer. 30 Communication problem 1. Check all connections are correctly connected. 2. If the error persists, please contact your retailer. Brake signal has an error 33 (If brake sensors are fitted) 1. Check all connectors. 2. If the error continues to occur, please contact your retailer. BF-UM-C-DP C11-EN November 2019 15 Error Declaration Troubleshooting 35 Detection circuit for 15V has an error Please contact your retailer. 36 Detection circuit on the keypad has an error Please contact your retailer. 37 WDT circuit is faulty Please contact your retailer. 41 Total voltage from the battery is too high Please contact your retailer. Total voltage from the battery is too 42 low Please contact your retailer. 43 Total power from the battery cells is Please contact your retailer. too high 44 Voltage of the single cell is too high Please contact your retailer. 45 Temperature from the battery is too Please contact your retailer. high 46 The temperature of the battery is too low Please contact your retailer. 47 SOC of the battery is too high Please contact your retailer. 48 SOC of the battery is too low Please contact your retailer. 61 Switching detection defect Please contact your retailer. (only with this function) 62 Electronic derailleur cannot release. Please contact your retailer. (only with this function) 71 Electronic lock is jammed Please contact your retailer. (only with this function) 81 Bluetooth module has an error Please contact your retailer. (only with this function) 16 BF-UM-C-DP C11-EN November 2019Adobe PDF Library 15.0 Adobe InDesign 15.1 (Windows)