User Manual for CAS models including: CAS IE-1700 Digital Crane Scale, CAS IE-1700, Digital Crane Scale, Crane Scale, Scale
CAS IE-1700 Digital Crane Scale - CAS Scales Australia
4 SAFETY GUIDE Read carefully the following instructio n and advice before using this scale. Over-loading this scale is harshly prohibited Refrain from long-time loading that could lead to excessive fatigue on loadcell used inside the scale. Excessive fatigue that on loadcell would decrease the
File Info : application/pdf, 15 Pages, 289.56KB
DocumentDocument
CONTENTS
SAFETY GUIDE................................................4 PRECAUTION...................................................4 PRODUCT CHARACTERISTICS................5 SPECIFICATION ..............................................5 MODEL ...............................................................6 SIZE AND NET WEIGHT...............................7 OPERATION......................................................8 ELECTRICAL PRINCIPLE DIAGRAM...10 DISPLAY MESSAGE .....................................11 TROUBLESHOOTING .................................12 REMOTE CONTROLLER...........................13
SAFETY GUIDE
Read carefully the following instruction and advice before using this scale.
¥ Over-loading this scale is harshly prohibited ¥ Refrain from long-time loading that could lead to excessive fatigue on loadcell
used inside the scale. Excessive fatigue that on loadcell would decrease the accuracy and shorten the life of scale. ¥ Check the shackle and hook regularly. ¥ Check the battery power level before/after use and recharge the scale in time. ¥ In order to maximize the battery life, periodic recharging is necessary for scales even not in use for long time. ¥ Do not try to repair the scale by yourselves. ¥ Use privately attached charger only.
PRECAUTION
¥ The crane scale is a kind of precise weighing instrument, pay attention on operantion and maintenance.
¥ Rotate the load instead of machine otself if necessary for operation. ¥ Stop using the machine under the circumstances of thunder & rain. ¥ Check periodicly if the clips/pins and screws of the machine are loose or broken
before use. ¥ If low battery signal appeare & LED annunciator goes green while charging,
please check the battery. ¥ Hang the machine instrad for storage while not in use in order to prevent from
unnecessary load in the weight sensor inside. ¥ Do not subject the scale to sudden to sudden temperature changes. ¥ Avoid from the shock of excessive weight.
PRODUCT CHARACTERISTICS
Model
Display
characteristics
IE Series
30mm(1.2)LED 30mm(1.2)LCD
High accuracy, small volume, easy to bring
¥ High quality: The process management is operated according to OIML R76,
GB/T11883-2002, and get the European CE certificate.
¥ Safty installation: Aluminum Die-Casting Case, high intensity hook and shackle,
special loadcell for safty installation.
¥ High reliability: Using high quality components on PCB circul board to board to insure
long time stability.
¥ Broad applicability: 30mm high character display, 25M distance eyeshot, can be used
in storage industry, textile industry, metallurgy industry etc.
¥ Simple operation: Check battry voltage automatically, wireless remote controller,
separate battery space, small volume, easy to bring.
¥ Complete function: Kg/Lb conversion, Hold, Tare, Division choice, Stablity regulation,
Accumulation/Search, Gross/Net conversion, parameter regulation etc.
SPECIFICATION
Standard
GB/T11883-2002zElectrical Crane Scale{
Accuracy class
OIML class III
Display
30mm(1.2) 5digits LCD/LED
Zero Range
4% full capacity
Tare Range
100% Full capacity
Stable Time
10 seconds
Overload Indication
100% Max. capacity + 9e
Max. Safety Load
125% Max. capacity
Ultimate Load
400% Max. capacity
Battery Life
50 hours
Battery Type
Fully sealed Lead-Acid battery, 6V/5Ah
Adapter
DC9V/1500mA
Operating Temp.
- 10 ~ + 40
Operating Humidity
85% RH under 20
Remote Controller Distance Min. 10m
Battery of Remote Controller 5# battery, 1.5V2
MODEL
Model IE-100
Max. capacity (kg / lb)
50/100
Min. capacity (kg / lb)
0.5/1
Division (kg / lb)
0.02/0.05
IE-200
100/200
1/2
0.05/0.1
IE-500
200/500
2/4
0.1/0.2
IE-1000
500/1000
4/10
0.2/0.5
IE-2000
1000/2000
10/20
0.5/1
Total display (kg / lb) n=2000 n=2000 n=2500 n=2000 n=2000
SIZE AND NET WEIGHT
Max.Capacity
100kg 200kg 300kg 500kg 1000kg
L (mm) 335 335 335 360 360
A (mm)
20 20 20 25 25
B (mm)
65 65 65 75 75
C (mm)
20 20 20 20 20
Net weight
4.0 4.0 4.0 4.2 4.2
Notice: If there's any modification, all the date are subject to the scale itself.
OPERATION
¥ TURN ON
Operation
OFF/ON
Display
8.8.8.8.8
500.0
U X.XX
-----
0
Illustration
Display two times Display capacity two times Display the voltage of battery Wait stable signal "STB" light, can hang the weight
Notice: To guarantee the accuracy, leave scale alone for 3~5 minutes after turning on.
¥ ZERO
Operation
Press0on scale Press ZERO on controller
Display
0
0
Illustration
After turn on, generally display
0, if not for
0
Can operate like this
¥ TARE
Operation
Display
Illustration
PressTon scale
Press TARE on controller
0 Press this key to deduct the weight of Container, while "TARE" light on, the
0 Scale will show the net weight of load
Notice: As crane scale deduct the weight of container automatically, so it will show the net weight of load every time, you needn't press this key to get net weight until you change the container or turn off.
OVERLOAD WARNING
The display will show-OL-once the load (Net + Tare) exceeds Max. capacity. Make sure that the load are within the capacity range, otherwise it's very dangerous.
¥ CHECK BATTERY
PressOFF/ONon scale, when turn on or turn off, it showsU X.XX
Press OFFon controller 2 seconds
Stable after 15 minute, it show
, after 60minutes, it turn off automaticaly.
¥ HOLD THE WEIGHT READING
Press "HOLD" key on the remote controller to hold the displayed weight reading. At this moment, "HOLD" light on, Press this key again will disable hold function.
¥ LOW BATTERY WARNING
When the battery voltage lower thenU 5.8.0, the display flash, but the scale can still work until the display show -Lb- , one minute later, it will turn off automatically, you need to recharge the battery to use again.
¥ POWER SAVING
The display will show when the load are at stable status in excess of 15 minutes and revert to normal weighing readings while load changes. When the load are at stable status in excess of 60 minutes, the scale will turn off automatically
¥ RECHARGING BATTERY
1. Turn off, connect the adapter with 220V AC power supply, also insert the plug in the socket which located in the rear of scale. The light become green, it means it's recharging automatically, until the green light become red, that means recharging is finished.
2. When you need to use crane scale hour after hour, take off the rear cover, change the battery with recharged battery.
Attention : Generally, the time of recharging should not lower than 8 hours, this scale have recharging protection function, long time recharging will not damage the battery.
¥ TURN OFF
PressOFF/ONon scale 2 seconds PressOFFon controller 2 seconds Stable after 15minutes, it show , after 60minutes, it turn off automatically.
ELECTRICAL PRINCIPLE DIAGRAM
Load cell
Signal enlarges
Control key
Control distance
A/D
CPU
LED or LCD display
Battery
DISPLAY MESSAGE
Display
Illustration
- - - - - Waiting stable
Err10 Accumulated weight not exceed Min. Capacity
Err11 Accumulated times exceed, (can't accumulate after 30times)
Err12 Accumulated weight exceed (can't accumulate after 99999)
CLr Ask if you really want to delete accumulated weight, in case error deletion
noCLr Give up deletion
88888 Confirm deletion
noACC No any accumulated value (when you check)
SHIFt Conversion, when you press SHIFT in controller
UX.XX The voltage of current battery
SCALE Enter weight adjustment
SEtUP Enter parameter adjustment
UAdJ Enter voltage adjustment
-OL- Overload warning
-Lb- Low battery warning
End End, when parameter adjustment ready
OFF Turn off
TROUBLESHOOTING
Phenomenon
Reason
No display when Turn on
Battery damaged Battery contact loosed
Display flash
Low battery Min.Capacity
Can't trun on & off
OFF/ONAbuttun damaged
Can't tare
TAREAbuttun damaged
Recharge indicator Light can't turn on
The recharger damaged
The recharger isn't plugged ready
The load is unstable
Display isn't stable
The display don't show "0" when empty load The error is large
Loadcell cable damaged
The scale in damp Environment for a long time No enough time for heating the scale after turn on Put the scale on ground for too long time
The scale isn't hung properly
Battery can't recharge
Battery damaged Outlet damaged
Remote distance
Receiver window is too dirty
shorten
Low battery of controller
Solution Check battery Tighten the contact Recharge the battery Check & clean the buttun Check & clean the buttun Check the recharger
Insert plug again
Stablize the load Check and replace loadcell Put the scale in dry Environment After turning on, heating 3-5 minutes. Scale should be hung
Check the scale and sling Replace battery Replace the outlet Check and clean Replace controller battery
REMOTE CONTROLLER GUIDE
¥ Lightness of display
Operation
Illustration
F1 0~5, 0: no display, 1: Minimum light, 5: Maximum light (Default: 2)
µ ZERO
Operation
Illustration
ZERO display 0 when no load, "ZERO" light on
µ HOLD
Operation
Illustration
HOLD Hold the weight, "HOLD" light on
HOLD Convert to weighing situation, "HOLD" light off
µ TARE
1. Tare directly
Operation
Illustration
TARE Display show net weight, "TARE" light on
TARE Display show gross weight, "TARE" light off
2. Set tare weight in advance
Operation MR TARE
display SHIFT 00000 ****
MR
- ***
Illustration
Current tare weight Input the tare weight Exit, "TARE" light on, it will deduct tare weight automatically when weighing.
µ ACCUMULATION
Operation
display
Illustration
. /P Current accumulation times
) Rear four digit of current accumulated value
- Front four digit of current accumulated value
Attention: After display two times circlely, it will return to weigh situation automatically, you also can press MR to return directly.
µ SEARCH
Operation
display
Illustration
.3 /P Current accumulation times
. Current weight
) Rear four digit of current accumulated value
- Front four digit of current accumulated value
.3
Return to weigh
Attention: Press5"3&and ª«can search every time weight and accumulated value, press
.3 return.
µ CLEAR
Operation $-&"3 $-&"3
display $-S OP$-S
Illustration
Display blink, please confirm if you want to delete Accumulated value
Cancel deletion
.3 Confirm deletion
µ ZERO DISPLAY
Operation .3 ª«
display
Illustration
4)*'5
Display current zero value
µ KG/LB CONVERSION
Operation display
Illustration
.3 4)*'5 Un = 0 : kg "lb" light off
$-&"3 6O Un = 1 : kg "lb" light on,
µ SEARCH OVERLOAD TIMES
Operation .3 $-&"3
display 4)*'5 0-
Illustration Display times of overload
µ VOLTAGE DISPLAY
Operation .3 ' .3
display
Illustration
4)*'5
6999 Display show current voltage of the battery
Return to weigh
µ TURN OFF
Operation 0''
display
Illustration
0'' 6999
Display show current voltage of battery then turn off
GPL Ghostscript 9.55.0