iDPRT AIDC | Barcode Printer Supplier, Label Printer, Scanner & More
User Guide for iDPRT models including: 01.Y.S.GT100004 Thermal Label Printer, 01.Y.S.GT100004, Thermal Label Printer, Label Printer, Printer
File Info : application/pdf, 2 Pages, 549.27KB
DocumentDocumentProduct Introduction Front View: Top Cover Left Cover Opening Button Power Button Paper Outlet Rear View: Inside View: Paper Inlet Panel Right Cover Opening Button Accessories Power Port USB Port Power Adapter*1 USB Cable*1 Ribbon Loading the Ribbon 01 Open the top cover and then open the panel Open the top cover first, then press the open cover button on both sides of the panel at the same time before lifting the panel upward. 02 Loading the Ribbon Install the ribbon into the printer by pinching the left and right wings of the ribbon with both hands. Note: The side with the anti-counterfeit label is facing the paper outlet. Putting in the paper 01 Putting in the paper Put in the paper as shown, up to 20 sheets of A4 paper can be placed at once. Power On 01 Connecting Power Plug the power cable into the power port on the back of the printer. Tips: All the drawings of the product and accessories in the manual are for reference only. Due to the updating and upgrading of the product, there may be some differences between the actual product and the drawings, please refer to the actual product. For more product information, please contact iDPRT customer service. Anti-Counterfeit Label 03 Close the Panel Turn the panel down and press it with both hands until you hear a "pop" sound. 02 Power On Long press the power button for 3 seconds to power on the printer. Note: Long pressing the power button can power off the printer. Future 999 Product Name: Wireless AI Printer Dimensions: 295.5*147.3*69.3mm Product Model: Future 999 Weight: About 1553g (excluded accessories) Input Parameter: DC 14V Operating Temperature: 0 ~ 40 Wi-Fi Connection: Wi-Fi IEEE 802.11b/g/n 2.4GHz Manufacturer: Xiamen Hanin Electronic Technology Co., Ltd. Add: No.96, Rongyuan Road, Tong'an District, Xiamen, China, 361100 Customer Service Email: idprt@afterservice.vip After Service Web : https://idprt.afterservice.vip Web: www.idprt.com +1 833 923 1143 After Service Printing Wirelessly from Mobile Phone 01 Download the App 04 Cloud Remote Printing The printer is on and the connected Wi-Fi hotspot can access the Internet; Even when the printer is not around you, you can still choose the file to print via the"HerePrint"App. After entering the print preview, send the data to the printer through remote printing. Scan the QR code or search"Hereprint"in APP store to download the"Hereprint"app. Printing from Windows PC Connect one side of the USB cable to the PC and the other side to the printer; Turn on the printer; Download the driver program from www.idprt.com and install it in the PC; Add the printer to the PC and print the documents from the PC after establishing the connection. 02 Connect to the printer via Wi-Fi Connect the mobile phone to Wi-Fi hotspot (select 2.4 GHz frequency band); Open the"HerePrint"app, click"+"in the top right corner of Home to add the device; Select the printer series according to the guide of app; Enter the Wi-Fi password; Waiting for the connection result. 03 Printing via LAN The printer is on and connected to the same Wi-Fi hotspot as the mobile phone; In the"HerePrint"app, select the file to print, enter"Preview"and confirm the parameters, then your mobile phone can send data to the printer via LAN. Precautions The best operating temperature is 0~40, if the environmental temperature is too low or too high, the print quality may be affected. Please do not use the unofficial adapter or ribbon to ensure the print quality. During printing, the area around the print head is very hot. Do not touch it, as you could be burned. Do not pull out paper by force during printing, or else it may damage the printer. In a domestic environment this product may cause radio interference. LED Indicator and Buzzer Definitions Error Status Status Print head temperature is too high Run out of ribbon Indicator Red LED flashes rapidly Red LED flashes slowly Out of paper Red LED flashes slowly Cutter jam Red LED flashes rapidly RFID error Red LED flashes slowly Printer cover is not closed Red LED is lighting *Buzzer sounds for 5 seconds and then stops Buzzer "Beep--beep beep--" "Beep beep beep--" "Beep beep beep--" "Beep--beep--beep--" -- --- -- Printer Status Status Power on process Power off Printing Firmware update Indicator Red, green and blue LED flashes alternately Light off White LED flashes slowly Red, green and blue LED flashes alternately Printer Status Status Bluetooth connecting In Wi-Fi connection Wi-Fi data receiving In USB connection USB data receiving No connection currently Indicator Blue LED flashes rapidly White LED is lighting White LED flashes rapidly Green LED is lighting Green LED flashes rapidly Blue LED is lighting FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with the FCC's RF Exposure guidelines. This equipment should be installed and operated with minimum distance between the radiator and your body (20cm). Use only the supplied antenna. FCC ID: 2AUTE-8TT22G Disclaimer Thank you for purchasing our product! By using this product, you hereby signify that you have read the Disclaimer and all warnings carefully and that you understand and agree to abide by the terms and conditions herein. The user should observe safe and lawful practices including, but not limited to, those set forth in this document. Our company therefore holds no liability for damages caused by force majeure, used by a third party, incorrect use, non-compliance with this user manual or intentional misconduct on the part of the user. Except for the scope prohibited by the applicable laws, the company is not responsible for any incidental, indirect, special or consequential damages, including but not limited to the loss of profits, income or data due to the violation of explicit or implied warranties or conditions mentioned in this user manual. Information in this user manual is for informational purposes only. It is subject to change without prior notice, due to the manufacturer's continuous development program. This document supersedes and replaces all information supplied prior to the publication hereof. Website: www.idprt.com Customer Service Email: idprt@afterservice.vip Future 999