Veneta® Blinds: Online Blinds | Shop Window Blinds Made To Measure – Veneta Blinds
Installation Guide for VENETA models including: 65101-40168-E Cordless Dual Blinds, 65101-40168-E, Cordless Dual Blinds, Dual Blinds, Blinds
How to Install – Veneta Blinds Dual Cordless Roller Blinds
File Info : application/pdf, 2 Pages, 4.98MB
DocumentDocumentHow to install your Dual Blinds Cordless (Roller Blinds with Raceway) #65101-40168-E Required Tools measuring tape drill with 2mm bit phillips bit or screwdriver Difficulty: pencil knife Included Hardware Installing inside the window frame The hardware can be found in the small hardware box included with your blind. 1 Blind Bracket Installation 32mm Hexagon Screw (for Mounting Bracket) 3 Insert the top light guard holder horizontally into the groove at the backside of raceway and turn 90 degrees to lock in the raceway groove.Then insert the top light guard into the groove of the top light guard holder. 19mm Round Head Screw 6 How to install your Dual Blinds Cordless (Roller Blinds with Raceway) #65101-40168-E Installation continued... Difficulty: Blind Bracket Cover Top Light Guard Holder (for Inside Mount) Mounting Brackets (for Outside Mount) Backside of Raceway Traditional Hold Down Bracket (Optional) Handle 6 1 Installing outside the window frame 1 Blind Bracket Installation Measure 75mm in from top left and top right of where the blind will sit, and mark where the screws will go. When installing the mounting bracket, the distance from the bracket's mounting hole to the edge of the window frame should be at least 19mm. Make sure all brackets line up with each other horizontally. Each bracket will require two 32mm hexagon screws for the installation. If more brackets are supplied, space them evenly between the first two brackets. 19mm 2 How to install your Dual Blinds Cordless (Roller Blinds with Raceway) #65101-40168-E Installation continued... 2 Blind Installation and Removal Before installing the shade into the mounting brackets, please locate the lock pin in the shade bracket on the end plug side. Slide the pin downward into the end plug to prevent the shade from falling. Difficulty: There are two ways to attach the shade to mount brackets.... A. Insert the back edge of the raceway into the back plastic part of the bracket, and then turn the raceway upwards so that the front rib of the raceway snaps into the bracket. B. Snap the front rib of the raceway into the bracket, and then turn the raceway backwards and upwards so that the back of the raceway is stuck to the back plastic part of the bracket. The hem bars of both the front & back blinds should be at the same height. Feedback? We would love to know how you went with your installation... Please write a review on our website at... www.venetablinds.com.au Removal of the Blind... Use a tool to push back the front or back plastic part of the brackets. Turn the back side of the raceway downward so that it detaches from the bracket. Finally remove the raceway by pulling downward from the brackets. or 3 Handle installation and Removal Attach Handle to Hem Bar... Step 1: Turn over hem bar and you can see a label attached at the center of the hem bar. Step 2: Align the center of the bottom of the handle with the label. Step 3: Hook the handle to the hem bar from top to bottom. Step 4: Press the handle from top to bottom to make the top of the handle clip into the hem bar. Step 5: Tear off the label from hem bar. 3 How to install, operate and maintain your Dual Blinds Cordless (Roller Blinds with Raceway) #65101-40168-E Installation continued... Label Difficulty: The center of handle should be aligned with the label. Remove handle from hem bar... Use straight screwdriver to pry the bottom of Handle from hem bar and then the handle can be removed. 4 Hold Down Brackets Installation (optional) Use 19mm round head screw to secure each bracket. 5 Cordless Operation Pull the handle downwards or upwards and the blind will be lowered or raised. The tension in our cordless roller blind can be adjusted to provide optimal light control and to ensure easy and dependable operation on a variety of window types and sizes. If a cordless blind begins to slide down on its own or it fails to roll up, the issue can be easily fixed by turning the adjustment dial towards "+" to increase the tension. Conversely, if the cordless blind cannot stop at the desired height and tends to roll up by itself, the tension can be decreased by turning the adjustment dial towards the "-". * The blind must be installed on the brackets when adjusting. Place the U- shape channel of pole under the handle and push up to lift the blinds. Use the "hook" portion to hook the handle to lower the blinds. Maintaining your Blind Need HELP? Call our Customer Service team for assistance 1300 836 382 Great Job... Enjoy your new Veneta Blinds! 1 Dusting Dust can be removed using a feather duster or vacuum with brush attachment on low suction. 2 Spot Cleaning Use a warm damp cloth or a mild detergent for tougher stains. Dab the affected area, but do not rub the fabric. Finish with just a warm damp cloth. Allow the fabric to dry in the lowered position. 4