Owner Manual Hall Tree

Important Notes

• Place all parts on a clean and smooth surface such as a rug or carpet to avoid the parts from being scratched.
• Before you begin, kindly follow the assembly instructions step by step.
• Do not tighten all screws and bolts until the unit is fully set-up.

Safety and Care Advice

Important - Please read these instructions fully before starting assembly:

• Check you have all the components and tools listed on the following pages.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area; small parts could choke if swallowed.
• Make sure you have enough space to layout the parts before starting.
• During assembly, do not stand or put weight on the product, as this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft, level surface to avoid damaging the unit or your floor.
• Parts of the assembly will be easier with 2 people.
• To reduce the likelihood of damaging your product, please ensure that your power drill is set on a low torque setting.

Care and Maintenance

• Only clean using a damp cloth and mild detergent; do not use bleach or abrasive cleaners.
• From time to time, check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take it to your local authority waste disposal centre.

Handy Hints

• Assemble all parts and bolts loosely during assembly; only once the product is complete should you fully tighten the bolts.
• Regularly check and ensure that all bolts and fittings are tightened properly.

WARNING

In order to help prevent overturning – please follow these instructions:

• Use the anti-tip strap or wall fixing method provided (if applicable).
• Do not allow children to climb or hang on the furniture.
• Do not open more than one drawer at a time.
• Do not place heavy items in the top drawers.
• Do not place heavy items on top of the furniture, unless the furniture has been designed for this purpose.

Parts List

• Part 1: Long panel x1
• Part 2: Long panel x1
• Part 3: Long panel x1
• Part 4: Short panel x1
• Part 5: Short panel x1
• Part 6: Back panel x1
• Part 7: Side panel x1
• Part 8: Shelf x1
• Part 9: Shelf x1
• Part 10: Divider panel x3
• Part 11: Base panel x1
• Part 12: Side panel x1
• Part 13: Side panel x1
• Part 14: Back panel x1
• Part 15: Base panel x1
• Part 16: Base panel x1
• Part 17: Shelf x1
• Part 18: Drawer front x4
• Part 19: Top panel x1
• Part 20: Side panel x1
• Part 21: Side panel x1
• Part 22: Back panel x2
• Part 23: Drawer side x4
• Part 24: Top panel x1
• Part 25: Shelf x1
• Part 26: Base panel x1
• Part 27: Base panel x1
• Part 28: Side panel x1
• Part 29: Top panel x1
• Part 30: Top panel x1
• Part 31: Back panel x1
• Part 32: Drawer base x1
• Part 33: Drawer base x1

Hardware List

• Hardware A: Screw (4x12MM) x77+2
• Hardware B: Screw (4x16MM) x77+2
• Hardware C: Screw (3x14MM) x58+2
• Hardware D: Screw (6x12MM) x6
• Hardware E: Screw (4x12MM) x54+2
• Hardware F: Screw (6x30MM) x4
• Hardware G: Hinge x2
• Hardware H: Hinge x5
• Hardware I: Screw (3.5x12MM) x78+2
• Hardware J: Screw (4x40MM) x2
• Hardware K: Screw (4x40MM) x8
• Hardware L: Screw (3x16MM) x4
• Hardware M: Screw (3x12MM) x2
• Hardware N: Screw (4x16MM) x8
• Hardware O: Screw (3x14MM) x8
• Hardware P: Screw (4x16MM) x8
• Hardware Q: Cam lock x2
• Hardware R: Cam bolt x2
• Hardware S: Screw (4x16MM) x4

Assembly Instructions

STEP 1

Attach part 19 (Top panel) to part 20 (Side panel) using hardware A (x4).

STEP 2

Attach part 21 (Side panel) to part 20 (Side panel) using hardware A (x4).

STEP 3

Connect part 22 (Back panel) to parts 20 (Side panel) and 21 (Side panel). Use hardware B (x4) and C (x4).

STEP 4

Assemble the structure from Step 3 by attaching part 21 (Side panel) to the base formed by parts 19 (Top panel) and 20 (Side panel). Use hardware B (x4) and C (x4).

STEP 5

Attach part 30 (Top panel) to the assembled structure.

STEP 6

Attach part 24 (Top panel) to the structure. Use hardware K (x4) and C (x4).

STEP 7

Attach part 24 (Top panel) to the top of the structure. Use hardware A (x4).

STEP 8

Attach part 29 (Top panel) to the base. Use hardware A (x6).

STEP 9

Attach part 28 (Side panel) to part 29 (Top panel). Use hardware A (x6).

STEP 10

Connect parts 22 (Back panel), 26 (Base panel), and 27 (Base panel) to parts 28 (Side panel) and 29 (Top panel). Use hardware B (x6) and C (x4).

STEP 11

Attach part 22 (Back panel) to parts 26 (Base panel) and 27 (Base panel). Use hardware B (x6) and C (x4).

STEP 12

Attach part 31 (Back panel) to the assembled structure.

STEP 13

Attach part 24 (Top panel) to the assembled structure. Use hardware B (x4) and C (x4).

STEP 14

Attach part 1 (Long panel) to the base. Use hardware A (x6) and R (x2).

STEP 15

Attach parts 5 (Short panel), 4 (Short panel), and 3 (Long panel) to the base. Use hardware B (x6) and C (x6).

STEP 16

Attach part 6 (Back panel) to the base. Use hardware R (x6).

STEP 17

Attach part 2 (Long panel) to the base. Use hardware A (x6).

STEP 18

Assemble parts 2 (Long panel), 5 (Short panel), 4 (Short panel), and 3 (Long panel). Use hardware B (x6) and C (x6).

STEP 19

Attach part 2 (Long panel) to the assembled structure. Use hardware A (x5).

STEP 20

Attach parts 12 (Side panel) and 14 (Back panel) to the base. Use hardware A (x12).

STEP 21

Attach part 15 (Base panel) to the base. Use hardware A (x6).

STEP 22

Connect parts 16 (Base panel) and 15 (Base panel). Use hardware B (x6) and C (x4).

STEP 23

Attach part 13 (Side panel) to part 15 (Base panel). Use hardware C (x2) and K (x2).

STEP 24

Assemble parts 12 (Side panel), 16 (Base panel), and 15 (Base panel). Use hardware B (x12) and C (x4).

STEP 25

Attach part 17 (Shelf) to the assembled structure.

STEP 26

Attach part 11 (Base panel) to the structure. Use hardware A (x6) and M (x2).

STEP 27

Attach shelves 7 (Side panel) and 8 (Shelf) to the side panel. Use hardware A (x2) and B (x2).

STEP 28

Assemble parts 7 (Side panel), 9 (Shelf), 11 (Base panel), and 10 (Divider panel). Use hardware A (x8), B (x8), C (x2), and K (x2).

STEP 29

Assemble parts 1 (Long panel), 14 (Back panel), 13 (Side panel), and 12 (Side panel). Use hardware B (x6) and C (x6).

STEP 30

Assemble parts 7 (Side panel), 2 (Long panel), and 8 (Shelf). Use hardware B (x5) and C (x4).

STEP 31

Attach parts 3 (Long panel), 4 (Short panel), 21 (Side panel), 12 (Side panel), and 29 (Top panel). Use hardware A (x2), D (x6), and B (x2).

STEP 32

Attach panels with multiple holes (part 10, Divider panel) to the main structure. Use hardware D (x54).

STEP 33

Attach parts 28 (Side panel) and 29 (Top panel) to the main structure. Use hardware F (x4).

STEP 34

Attach part 25 (Shelf) to the main structure.

STEP 35

Attach hinges H to parts 32 (Drawer base) and 33 (Drawer base). Use hardware I (x10).

STEP 36

Attach doors (parts 33, 20, 28, 32) using hinges G (x2) and hardware I (x20).

STEP 37

Attach drawer fronts (part 18) to drawer sides (part 23). Use hardware S (x4), O (x8), I (x48), P (x8), N (x8).

STEP 38

Attach the top decorative molding. Use hardware L (x4).

STEP 39

Attach handles to doors/drawers. Use hardware J (x2) and Q (x2).