Instruction Manual for BUSTER Punch models including: RF 1-10V, Premium Led Push Dimmer, RF 1-10V Premium Led Push Dimmer
Please read before installing. 1. These product s must be installed in acco rdanc e with the latest Building and IEE wiring regula tions.
4G Dimmer Switch - SALT Store
ELECTRICITY 1G, 2G, 3G & 4G PREMIUM LED PUSH DIMMER BUSTERANDPUNCH.COM DIMMER TECHNICAL SPEC. DIMMER STYLE: 1G, 2G, 3G, 4G PREMIUM LED PUSH DIMMER. LED / CFL 1,2,3,4 GANG 5-120w max HALOGEN / INCANDESCENT 1 GANG 2,3,4 GANG 400w max 250w max. MINIMUM BRIGHTNESS LEVEL SETTING How to set the minimum brightness level: Operate steps of Dimmer and Switch Actions ON OFF Max 1 Min Max Dimmer With the Lamp in an OFF state, at max. positon, push ON and wait 5 seconds until lamp stablises. ON Max 2 Min Max Dimmer ON OFF Min Turn to min. position. Push OFF and push ON at min. brightness level. Turn to max. position. Push OFF ON 3 Min Flash ON and push ON again. The lamp OFF 1 time 50% will appear to flash once at half- Min Max brightness level. You have now Dimmer entered Minimum Dim Set Mode. ON 4 50% Min Max Dimmer Set your desired min. brightness level. Push OFF and ON once. The lamp will appear at half- OFF ON brightness level then return to normal brightness level. It has now configured and saved your settings. Each step must be performed within 10 seconds, if not,it will time out and auto exit the programme without saving. If you wish to terminate the setting mode, push OFF whilst the lamp is flashing. INSTALLATION 1. Before commencing work, isolate the mains power supply and remove the fuse in the fuse box or switch off the circuit breaker in the consumer unit. 2. If unit is to be used as a replacement for an existing product, remove existing unit from its location and disconnect the wiring. CAUTION: Verify power is OFF to switch before proceeding. 3. Connect the wires as shown in appropriate wiring diagrams. Use green/yellow sleeving on earth conductors not insulated. Ensure terminals are properly tightened and no bare wire is visible. Push back unit into moulding box making sure conductors are not trapped. If installing standard incandescent bulbs, check the total load of the module is between 60W and 400W max. If installing LED bulbs, check the total load of the module is between 5W and 120W max. DIMMER ON 1 WAY CIRCUIT Phase 2 Live Neutral Earth Brown Blue Yellow and Green Your product is supplied in 2 boxes, one box containing the switch plate and a further box containing the details kit. Open the details kit box and install the plate as follows. By hand, screw nut A in place (orientate as shown). Align Flat C to the corresponding flat on the inside of the Dimmer Knob B. Push the dimmer knob in place by hand. Use a cross head electric or manual screwdriver to fit the special countersunk screws until tight*. IMPORTANT NOTES Please read before installing. 1. These products must be installed in accordance with the latest Building and IEE wiring regulations. If in any doubt, please contact a qualified electrician. 2. This dimmer is only suitable for incandescent, halogen, dimmable LED and dimmable LED-filament bulbs, but is not suitable for non dimmable LED or any CFL bulbs. 3. Dimmer comes set at Leading Edge as factory default, Please check with an electrician that your circuit is Leading Edge if not follow the instructions to change the mode of the dimmer. BACK BOXES We recommend you to use a UK back box to install your product. Please note that the minimum recommended depth for the mounting box is 47 mm. Back boxes are available to purchase from us, please see recommended sizes below: DIMMER PLATE 1G - 2G 3G - 4G RECOMMENDED BACKBOX 1G UK Back box SKU# ELB921 2G UK Back Box SKU# ELB922 RECYCLING ELECTRICAL PRODUCTS Buster and Punch encourages all of its customers to make note of this symbol and avoid putting any waste electrical goods in your domestic waste bin or container. Please ensure you take your waste electrical goods to a suitable facility for disposal. MODE SETTING H o w to se t Trailing Edge (T E) or Le adin g Edge ( LE) Mod e. (Factory default is TE mode): To set LE mode follow steps 1-4. To revert back to TE mode, follow steps 1-3 and 5. Operate steps of Dimmer and Switch Actions OFF 1 ON Min Min Max Dimmer Set the lamp to min. position whilst in OFF state. Wait for around 5 seconds to push ON, until the lamp appears stable. 4 (LE mode) ON 2 Min ON 3 Max ON Max ON Min Min Max Dimmer ON OFF Max Turn to max. position. Push OFF and push ON. Min Max Dimmer Flash OFF 1 time Turn to min. position, push OFF and push ON again. Lamp will ON Min appear to flash 4 times at half- bright level. You can now either follow step 4 to enter TE mode or step 5 to enter LE mode. To Select LE mode (for special required) Min Max Dimmer Turn to max. position, push OFF Flash ON OFF 1 Max and push ON at max brightness time level to confirm and save setting with flash 3 times. To select TE mode (Factory default) Min Max Dimmer Flash OFF 1 time At min. position, push OFF and ON push ON at min. brightness level Min to confirm and save setting your desired setting. The lamp will flash once. Each step must be performed within 10 seconds, if not, it will time out and auto exit program without saving. 5 (TE mode) DIMMER ON 2 WAY CIRCUIT c Dimmer Phase 2 Live Neutral Earth Brown Blue Yellow and Green By hand, screw the coin caps into the end of the screws. Use the plastic coin cap tool to fully tighten the coin caps**. 2 WAY SWITCH DIMMER ON 3 WAY CIRCUIT 2 WAY SWITCH c Dimmer Phase 2 Live Neutral Earth Brown Blue Yellow and Green * Please ensure screws are sufficiently tight to support the product but please do not over tighten as this may cause some deformation to the plate or damage the screw. ** Do NOT use a standard screw driver to tighten the coin caps. This may damage the cap and is not covered under warranty. Plastic coin cap tool must be used by hand only. 5. To red uce the risk of dis colouration or tarnishing , avoid installation on wet plaster. c Dimmer 6. Turn po wer b ack on.Adobe PDF library 15.00 Adobe Illustrator(R) 24.0