Laxihub P2(T) Quick Guide

Quick start guide

• Packing list
• Product description
• Installation
• Product configuration
• Specification
• Legal notice

1. Packing list

• Camera X1
• Power adaptor X1
• Power cable X1
• Bracket X1
• Screw X3
• Quick guide X1

2. Product description

A visual representation of the camera with numbered parts:

• 1. LED indicator
• 2. Microphone
• 3. Speaker
• 4. Reset button
• 5. Power port
• 6. SD card slot

3. Installation

1. Use the included mounting bracket to fix the camera to a clean surface.
2. Put the camera on a flat surface.

Installation diagrams show mounting the camera to a ceiling and placing it on a flat surface.

Notice

To reset the device, press and hold the reset button for 5 seconds. The camera beeps when the operation is completed.

LED indicator of camera:

4. Product configuration

Scan QR code to download and install the Arenti APP. Also, you can search "Arenti" on App Store (iOS) or Google Play (Android).

App store download buttons and QR codes for iOS and Android are displayed.

Registration

Open the App. If you are a new user, tap to create a new account and follow the prompts to complete account setup. Note: You must agree with the Privacy Agreement.

A screenshot of the app's registration/login screen is shown.

Pairing

Open APP home page. Click "+" or "Add" and select icon according to actual camera. Power on the device. For about 30 seconds, the camera will emit start-up tone and LED indicator will flash red slowly. Note: When pairing, please put the camera and mobile phone close to the router. If camera is not in the red slow blinking after 30 seconds of powering on, press and hold the reset button for 5 seconds to reset, and then configure the network again.

Screenshots illustrate the process of adding a device and scanning a QR code.

Select the Wi-Fi network and input the password, and then click "Next". Make sure that your phone has connected to a fluent and steady Wi-Fi already.

A screenshot shows the Wi-Fi network selection screen, emphasizing the need for a 2.4GHz network.

Scan the QR code in your phone with the camera and click "Next", when the camera comes out "dong dong dong" and LED indicator becomes solid blue.

Screenshots show the operation instructions for scanning the QR code.

If no device is found and the pairing process is not successful, please check below instructions:

1. Wi-Fi network is 2.4GHz.
2. Wi-Fi password entered is correct and the same Wi-Fi network is used on the mobile device.
3. Camera is in pairing mode.
4. Check your WiFi for network activity.

If there doesn't work please or you have any other problems, please contact support@arenti.com to get help.

Notice

If you have multiple cameras, please follow steps again to add devices one by one. To change Wi-Fi network, please restore the camera to factory settings and follow steps to add the camera.

5. Specification

6. Legal notice

Support: www.arenti.com

Symbols

? Direct current (DC)

A symbol depicting a crossed-out trash can with a battery inside indicates not to dispose of batteries with household waste.

Don't throw batteries or out of order products with the household waste (garbage). The dangerous substances that they are likely to include may harm health or the environment. Make your retailer take back the products or use selective collect of garbage proposed by your city.

CE

Hereby, Laxihub declares that the radio equipment type 'P2(T)' is in compliance with the Directive 2014/53/EU. The full test of the EU declaration of conformity is available at the following Internet address: www.arenti.com

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and consider removing the no-collocation statement.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution!

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Safety Information

Power Adapter Safety:

1. The power plug is intended to serve as a disconnect device. Do not drop or cause an impact to the power adapter.
2. If the power cable is damaged (for example, the cord is exposed or broken), or the plug loosens, stop using it at once. Continued use may lead to electric shocks, short circuits, or fire.
3. Do not touch the device or the power adapter with wet hands. Doing so may lead to short circuits, malfunctions, or electric shocks.

Child's safety

1. Comply with all precautions with regard to child's safety. Letting children play with the device or its accessories may be dangerous.
2. The device and its accessories are not intended for use by children. Children should only use the device with adult supervision.

Operation safety

1. Use the device under allowed humidity and temperature conditions.
2. Do not aim the device at strong light sources (such as lamplight, and sunlight) when focusing it, to avoid reducing the lifespan of the CMOS sensor, and causing overbrightness and flickering.
3. Observe local laws and regulations, and respect the privacy and legal rights of others.

© 2023. All rights reserved. All trade names are registered trademarks of respective companies. Apple, the Apple logo, iPhone are trademarks of Apple Inc. registered in the U.S. and other countries. Google, the Google logo, Android are trademarks of Google Inc. App Store is a service mark of Apple Inc. Google Play is a service mark of Google Inc.

V1.0 202306