Oraimo OIM-812A Nugget Ice Maker

1. IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE AND SAVE FOR FUTURE REFERENCE.

When using an electrical appliance, especially when children are present, basic safety precautions should always be followed, including the following:

INTENDED USE

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by person responsible for their safety.
• Close supervision is necessary when any appliance is used by or near children. Children should be supervised to ensure that they do not play with the appliance. Cleaning and user maintenance shall not be done by children unless they are older than 8 and supervised. Keep the appliance and its cord out of reach of children.
• Use the appliance only for intended household purposes as described in this User Manual.

ELECTRICITY SAFETY

• This appliance must be provided with correct voltage via a professionally installed power socket. Make sure the voltage indicated on the label of the appliance is the same as your local supply.

RELATED TO USE

• DO NOT attempt to disassemble, repair, modify or replace any part of the appliance. No user serviceable parts inside. All servicing should be performed by qualified personnel only.
• Always place and use the appliance on a dry, stable and level surface with sufficient ventilation, away from heat sources. Leave at least 6 inches (15 cm) of clearance on the sides and back for proper ventilation.
• Always turn the appliance OFF and unplug it before cleaning, or whenever not in use.
• Always turn the appliance OFF and unplug it before making any repairs or servicing to avoid electric shock or UV radiation.
• DO NOT sit on or place any object on top of the appliance.
• DO NOT use with water that is micro-biologically unsafe or of unknown quality.
• DO NOT use mechanical devices to defrost. Carry out self-cleaning cycle to remove any frozen parts.
• If the appliance is stored in a cold environment, wait at least 3 hours for the appliance to warm to room temperature before plugging it in.
• Regarding the use of flammable blowing agent and refrigerant, dispose of the ice maker in accordance with local regulations.
• Use caution and handle with care when moving, handling and using the ice maker to avoid damaging to the refrigerant tubing or increasing the risk of leakage.
• Damaged parts (e.g., compressor, condenser, motor and copper pipe etc.) shall be replaced with the same one by authorized personnel to minimize the risk of possible ignition resulting from incorrect parts or improper servicing.
• This ice maker complies with the applicable terms in Code of Federal Regulations, including 21 CFR, Chapter 1.
• DO NOT attempt to replace UV lamp by yourself. Have the lamp replaced by authorized personnel only.

FOR HOUSEHOLD USE ONLY. SAVE THESE INSTRUCTIONS.

Specifications

2. KNOWING YOUR ICE MAKER

This section details the components and features of your Oraimo Ice Maker.

Front View Components:

• Ice Scoop: A plastic scoop provided for removing ice.
• Ice Bin: The compartment where ice is collected.
• Control Panel & Display: Contains buttons for operation and an LED screen showing status and times.
• Water Tank: Reservoir that holds water for ice production.
• MAX Fill Line: Indicates the maximum safe water level in the tank.
• Front Door (with Transparent Window): Allows viewing of the ice level.
• Ice Full Sensor: Detects when the ice bin is full and stops ice production.
• Water Filter: Located within the water tank area to purify water.
• Water Level Detector: Monitors the water level in the tank.

Rear View Components:

• Drain Plug: Located at the bottom rear for emptying the water tank.
• Drainpipe (for water tank): Connects to the drain plug for water removal.
• Drainpipe (for water line): Used when connecting to a water supply system.
• Water Inlet (for Automatic Refill): Port for connecting the water supply hose.
• Power Cord: For connecting the unit to a power source.
• Inlet Pipe: Included hose for water connection (9.8ft./3m).

3. USING YOUR ICE MAKER

Getting Started

• Ensure the drain plug is firmly inserted before use.
• The ice maker will stop making ice if the ice bin is pulled out for more than 5 minutes. Ensure it is replaced within 5 minutes to continue the cycle.
• Locate and Clean: Place the ice maker upright on a flat, level surface with at least 6 inches (15 cm) of clearance on the sides and back for ventilation. Clean the water tank, ice bin, and ice scoop. Allow the unit to settle for at least 2 hours before first use.
• Add Water Manually: Open the front door and pull out the ice bin. Fill the water tank with potable water, ensuring it is below the MAX fill line. Recommended water type: distilled or demineralized water (hardness < 12 grains per gallon) at 40-82°F (4-28°C). Place the ice bin back and close the door.
• Start Making Ice: Plug the unit into a properly installed grounded outlet. Press the ON/Standby button [Power Button] to start the ice-making cycle. The unit will continue making ice until the ice bin is full.
• Scoop Ice Out: The ice maker will start producing ice in approximately 15 minutes. Scoop the ice cubes out as they are made. Put the ice into use or store it in a freezer to avoid melting.

Automatic Refilling

To add water automatically, connect the included hose to your home's water supply system. An adapter (not included) may be required depending on your system.

To avoid overflow, do not add water manually when the ice maker is already connected to the water supply system.

• Insert the Hose: Fully insert the included hose into the water inlet port on the back of the unit until it is fully seated. To remove, hold the gray ring and pull the hose out.
• Connect with Water Supply System: Connect the other end of the hose to your water supply system. A 1/4" connector may be required. It is recommended to connect with a water filtration system to prevent blockage from scale or mineral build-up.

4. CLEANING AND MAINTENANCE

To keep your ice tasting fresh, it is recommended to perform self-cleaning at least once every 1 to 2 weeks.

Self-Cleaning

• Hold the CLEAN button [Clean Button] for 3 seconds to start or cancel the self-cleaning cycle.
• The ice maker will auto-clean for the first 3 minutes (the CLEAN indicator [Clean Indicator] stays on). After 3 minutes, the indicator will flash quickly for 5 minutes to confirm whether to proceed with a deep clean. Press the CLEAN button again to confirm. If no operation is performed within 5 minutes, the cleaning cycle will stop automatically.
• Once cleaning is done or cancelled, the ice maker will enter standby mode.
• After continuous running for 100 hours, the CLEAN indicator [Clean Indicator] will flash slowly for 30 seconds to remind you to clean the ice maker. Hold the CLEAN button [Clean Button] for 3 seconds to start cleaning.

Regular Cleaning

To remove fallen dirt or fibers, it is recommended to clean the ice bin and water tank once a week. Unplug the unit before cleaning.

1. Unplug and take out the ice bin. Remove the water filter from the right corner of the tank.
2. Rinse the ice bin and water filter with diluted detergent and warm water.
3. Clean the water tank with diluted detergent, warm water, and a soft cloth. Add water to rinse and then drain out the water.
4. Gently wipe the exterior with a soft, damp cloth.

Removal of Scale / Mineral Build-up

For scale or mineral build-up, follow these directions for deep cleaning periodically or when needed. Do not clean with solvents or chemicals.

1. Fill the water tank with warm water (around 90°F / 32°C) below the MAX line or connect with the water supply system.
2. Add distilled white vinegar or an ice maker cleaner. Let it sit for at least 18 hours.
3. Hold the CLEAN button [Clean Button] for 3 seconds to start the self-cleaning cycle. If the indicator flashes, press the CLEAN button [Clean Button] to continue. Repeat for at least 3 cleaning cycles.
4. Drain the mixture and continue running 3 cleaning cycles with fresh water for each rinse.

When not in use for an extended period of time, drain the water tank and clean as instructed. Cover and store in a cool, dry location away from direct sunlight.

5. TROUBLESHOOTING GUIDE

The troubleshooting guide addresses the most common problems. If problems persist, feel free to contact the Customer Support at contact@oraimo.com.

6. WARRANTY AND SERVICE

Thanks for choosing Oraimo Ice Maker.

This product is covered with Oraimo product and labor warranty for 12 months from the date of its original purchase.

The warranty will not apply in cases of:

• Misuse, dismantling, or repairs performed by unauthorized personnel.
• Any appliance that has been tampered with or used for commercial purpose.
• Use of force, natural hazards, damage caused by external influences.
• Damage caused by non-observance of the User Manual, e.g. connection to an unsuitable mains supply or non-compliance with the instructions.
• Partially or completely dismantled appliances.
• Defects caused by or resulting from damages from shipping or alteration to the product or any of its parts that have been performed by unauthorized personnel.

We can only provide after-sales service for products that are sold by Oraimo or Oraimo authorized retailers and distributors. If you have purchased your appliance from a different place, please contact your seller for return and warranty issues.

※Please have your order ID ready before contacting Customer Support.

Warranty Certificate

Customer's Name: [____________________]

Order ID: [____________________]

Product Model: OIM-812A

Problem Description: [____________________]

This product is covered by a guarantee from the date of purchase. The warranty is valid only when the warranty card is properly completed. Warranty is limited to the core product. Accessories included in the package are not covered. Please contact us if you have a question or experience a problem with the product, we promise we will give you a satisfied solution within 24 hours.