Anslut Heater Fan
Model: 015181
Operating Instructions
Important! Read the user instructions carefully before use. Save them for future reference. (Translation of the original instructions)
Description
1. POWER Indicator/Button
2. Thermostat Dial (MIN to MAX)
3. Mode Selector Dial
4. Fan Symbol (Fan Mode)
5. Low Heat Output + Fan Symbol (Low Output Mode + Fan)
6. High Heat Output + Fan Symbol (High Output Mode + Fan)
Before Use
- Unpack the product and all parts from the packaging and place them on a level surface.
- Check that the mains voltage corresponds to the rated voltage on the type plate. Plug in the plug. The product is now ready to use.
Important:
- Do not place the product near walls or corners, where incoming or outgoing air can be blocked.
- Do not place the product directly below a power outlet.
How to Use
- Place the product standing upright on a level, stable surface at a safe distance from flammable objects and substances.
- Plug the plug into the power point.
- Set the thermostat dial to the required mode.
- Start the product by setting the mode selector to the required output.
- The heating element switches off when the set room temperature is reached, including the fan. The heating element and fan start again when the temperature drops. The product starts and switches off automatically to maintain a constant room temperature.
- To switch off the product, set the thermostat to MAX and put the mode selector in fan mode. Allow the product to run for two minutes to cool and then switch off the product and pull out the plug.
Maintenance
Note: Switch off the product, pull out the plug, and wait until the product has completely cooled before cleaning and/or maintenance.
- Wipe off any dust from the surface of the product with a soft cloth. When necessary, clean with a cloth moistened with a mild detergent and then dry with a soft cloth.
- Do not use petrol, solvent, or strong detergent. This can damage or discolour the product.
Storage
- Pull out the plug and cover the product to protect it from dust if it is not going to be used for some time.
- Store the product in a cool, dry, and well-ventilated place.
Troubleshooting
| Problem | Possible Cause | Action |
|---|---|---|
| The product does not start, even though it is plugged in and switched on and the thermostat is set to the required mode. | No power supply. | Plug the plug into a power point that is supplied with power. |
| The heater element glows. | Voltage too high. | Check that the mains voltage corresponds to the rated voltage on the type plate. |
| The fan is working, but the product does not get hot. | The air inlet is blocked. | Make sure there are no foreign objects that can block the air inlet, such as curtains, plastic bags, or paper etc., near the product. |
| Heating mode not set. | Set the required heating mode. | |
| The set thermostat value has been reached. | Turn the thermostat dial and listen for a click when the thermostat is activated/deactivated. If you do not hear a click and the thermostat is not damaged, the product will start automatically when it has cooled. | |
| The overheating protection has tripped. | Switch off the product, pull out the plug, and check that the inlet or outlet openings are not blocked. Wait at least 10 minutes so that the overheating protection has time to reset before starting the product again. | |
| Abnormal noise. | The product is not correctly positioned. | Place the product on a level surface. |
Technical Data
| Item | Symbol | Value | Unit |
|---|---|---|---|
| Heat output | |||
| Nominal heat output | Pnom | 2 | kW |
| Minimum heat output (indicative) | Pmin | 1.0 | kW |
| Maximum continuous heat output | Pmax,c | 2 | kW |
| Auxiliary electricity consumption | |||
| At normal heat output | elmax | N/A | kW |
| At minimum heat output | elmin | N/A | kW |
| In standby mode | elSB | N/A | kW |
| Type of heat input, for electric storage local space heaters only (select one) | |||
| Manual heat charge control, with integrated thermostat | No | ||
| Manual heat charge control with room and/or outdoor temperature feedback | No | ||
| Electronic heat charge control with room and/or outdoor temperature feedback | No | ||
| Fan assisted heat output | No | ||
| Type of heat output/room temperature control (select one) | |||
| Single stage heat output and no room temperature control | No | ||
| Two or more manual stages, no room temperature control | No | ||
| With mechanic thermostat room temperature control | Yes | ||
| With electronic thermostat room temperature control | No | ||
| Electronic room temperature control plus day timer | No | ||
| Electronic room temperature control plus week timer | No | ||
| Other control options (multiple selections possible) | |||
| Room temperature control, with presence detection | No | ||
| Room temperature control, with open window detection | No | ||
| With distance control option | No | ||
| With adaptive start control | No | ||
| With working time limitation | No | ||
| With black bulb sensor | No | ||
Safety Instructions
Warning! ⚠️ Some parts of the product get very hot - risk of burn injuries. Keep the product under careful supervision when it is used by, or near children or persons with functional disorders.
- Do not put any foreign objects on the product.
- Never poke your fingers or any other objects into the inlet or outlet openings.
- Do not use the product near a bath, shower, or swimming pool.
- Do not cover the product, this can result in overheating.
General Safety:
- Keep children less than 3 years old under supervision when they are near the product. The product can be switched on/off by children from 3 to 8 years old only if it is mounted in the correct position to use, and if they are supervised or receive instructions concerning the safe use of the product and understand the risks involved. Do not allow children from 3 to 8 years old to connect, use, clean, or maintain the product.
- This product can be used by children from 8 years and upwards and by persons with physical, sensorial, or mental disabilities, or persons who lack experience or knowledge, if they are supervised or receive instructions concerning the safe use of the product and understand the risks involved. Keep children under supervision to make sure they do not play with the product. Do not allow children to clean or maintain the product without supervision. Keep children less than 3 years old under supervision when they are near the product.
- The product is only intended for household use.
- Pull out the plug if the product is not going to be used for some time.
- Do not run the power cord in front of the product.
- The product must only be connected to a correctly installed and earthed power point. Check that the mains voltage corresponds to the rated voltage on the type plate.
- Make sure to plug the plug firmly in the power point. Do not touch the power cord or the plug with wet hands.
- Put the switch in the OFF position and pull out the plug when the product is not in use.
- Do not route the power cord under carpets etc. Place the power cord so that there is no risk of treading on it, or tripping over it.
- Do not expose children to the flow of air from the product for long periods.
- Only use the product in a well-ventilated area.
- Do not place the product near walls or corners, where incoming or outgoing air can be blocked.
- Do not put the product near curtains or other flammable materials – fire risk.
- Do not expose the product to vibrations, knocks, or blows when in use.
- The product is not intended to be controlled with an external timer or a separate remote control that can make the product start automatically.
- Do not use longer than necessary extension cords. Always unfold the complete extension cord.
- Do not connect other appliances to the same power outlet the product is using.
- Never leave the product unattended when plugged in. Keep children and pets at a safe distance.
- Never put the product in a vehicle that is moving or on any other surface where there is a risk of it tipping over.
- Place the product where the air flow cannot be blocked by furniture or curtains, etc.
- Do not use the product in explosive environments, for example, in the vicinity of flammable liquids, gas, or dust. Do not place the product near a naked flame or other source of heat.
- Do not attempt to dismantle or repair the product. Repairs should be carried out by qualified personnel or an authorised service centre.
- A damaged cord or plug must be replaced by an authorised service centre or qualified person to ensure safe use.
- Switch off the product immediately and pull out the plug in the event of any abnormal noise, smell, smoke, or other sign of a problem.
Symbols
- ? Read the instructions.
- ? Do not cover.
- ✅ Approved in accordance with the relevant directives.
- ♻️ Recycle discarded product in accordance with local regulations.
Contact Information
For the latest version of the operating instructions, see www.jula.com
Manufacturer: Jula AB, Box 363, 532 24 SKARA, Sweden
Distributor: Jula Poland Sp. z o.o., Jula Norge AS, etc. (See PDF for full details)
Contact details: www.jula.com
