HORIZON AXI03005 RC Remote Control Model Car Crawler Instruction Manual

Instruction Manual for HORIZON models including: AXI03005, RC Remote Control Model Car Crawler, Model Car Crawler, Remote Control Model Car, AXI03005, Crawler

RBX10 1/10 Scale Rock Bouncer

PDF RBX10 1/10 Scale Rock Bouncer

EN 2 RBX10 RYFT ROCK BOUNCER, 1/10 RTR Age Recommendation: Not for children under 14 years. This is not a toy. WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.

File Info : application/pdf, 20 Pages, 7.68MB

AXI03005-Manual-EN

AXI03005
RBX10 1/10 Scale Rock Bouncer
INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D'UTILISATION MANUALE DI ISTRUZIONI
Before operating this vehicle, please read all printed materials thoroughly. Horizon Hobby is not responsible for inadvertent errors in this manual.

EN
NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit www.horizonhobby.com or www.towerhobbies.com and click on the support or resources tab for this product.

MEANING OF SPECIAL LANGUAGE
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product: WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superficial injury. CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury. NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury. This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maitenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

Age Recommendation: Not for children under 14 years. This is not a toy.

SAFETY PRECAUTIONS AND WARNINGS

As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the product or property of others.
This model is controlled by a radio signal subject to interference from many sources outside your control. This interference can cause momentary loss of control, so it is advisable to always keep a safe distance in all directions around your model as this margin will help avoid collisions or injury.

· Never operate your model with low transmitter batteries. · Always operate your model in open spaces away from full-size vehicles,
traffic and people. · Never operate the model in the street or in populated areas for any reason. · Carefully follow the directions and warnings for this and any optional
support equipment (chargers, rechargeable battery packs, etc.) you use. · Keep all chemicals, small parts and anything electrical out of the reach of
children. · Never lick or place any portion of the model in your mouth as it could
cause serious injury or even death. · Exercise caution when using tools and sharp instruments.

· Take care during maintenance as some parts may have sharp edges. · Immediately after using your model, do NOT touch equipment such as the
motor, electronic speed control and battery, because they generate high temperatures. You may burn yourself seriously touching them. · Do not put fingers or any objects inside rotating and moving parts, as this may cause damage or serious injury. · Always turn on your transmitter before you turn on the receiver in the car. Always turn off the receiver before turning your transmitter off. · Keep the wheels of the model off the ground when checking the operation of the radio equipment.

TABLE OF CONTENTS

Box Contents ............................................................................................................. 3 Water-Resistant Vehicle With Waterproof Electronics.................................... 3 General Precautions............................................................................................... 3
Wet Conditions Maintenance ............................................................................... 3
Quick Start ................................................................................................................. 3 Components ............................................................................................................. 3
Charging the Battery ................................................................................................ 4 Installing the transmitter Batteries....................................................................... 4 Transmitter Functions .............................................................................................. 4 SR6100AT AVC Technology Telemtry Receiver ................................................... 5 Installing The Vehicle Battery ............................................................................... 5 Binding And Calibrating The Receiver ................................................................ 5 Disabling AVC® Technology Stability Assist....................................................... 5
Failsafe...................................................................................................................... 5
Aux channels ........................................................................................................... 5
Driving Precautions ................................................................................................ 6 Powering On The Vehicle ....................................................................................... 6 Before Running Your Vehicle ................................................................................. 6 AVC Sensitivity.......................................................................................................... 6 Run Time..................................................................................................................... 6 To Improve Run Times ............................................................................................ 6
Performing A Control Direction Test..................................................................... 6 Changing The Travel Adjust Settings.................................................................... 7 Vehicle Fluids............................................................................................................ 7

SpektrumTM FirmaTM SMART 130A Brushless ESC ................................................ 7 Specifications.......................................................................................................... 7
ESC LED Status........................................................................................................ 7
Audible Warning Tones.......................................................................................... 7
Esc Calibration Procedure..................................................................................... 7
Descriptions............................................................................................................. 8
ESC Programming Procedure............................................................................... 8
Esc Functions And Modes..................................................................................... 8
Programming Table................................................................................................. 8
SpektrumTM FirmaTM 2200Kv 4-Pole Brushless Motor........................................... 9 Precautions.............................................................................................................. 9
Gearing .................................................................................................................... 9
Setting The Gear Mesh .......................................................................................... 9
Telemetry Settings .................................................................................................. 9
Troubleshooting Guide ............................................................................................ 9 Limited Warranty ................................................................................................... 10 Warranty And Service Contact Information ...................................................... 10 FCC Information....................................................................................................... 11 IC Information.......................................................................................................... 11 Compliance Information For The European Union ........................................... 11 Replacement Parts ................................................................................................. 45 Recommended Parts .............................................................................................. 46 Optional Parts.......................................................................................................... 47 Exploded View ........................................................................................................ 48

RBX10 RYFT ROCK BOUNCER, 1/10 RTR

BOX CONTENTS

EN
COMPONENTS · Axial® RyftTM Rock Bouncer 4WD RTR: 1/10-Scale (AXI03005) · SpektrumTM SMART DX3, 2.4GHz Transmitter (SPM2340) · Spektrum SR6100AT 6 Channel AVC® Telemetry Surface Receiver
(SPMSR6100AT) · Spektrum S614S 15KG, Steel Gear Waterproof Servo (SPMS614S) · Spektrum FirmaTM SMART 130A Brushless ESC (SPMXSE1130) · Spektrum Firma 2200Kv 4-pole Brushless Motor (SPMXSM2700) · 4 AA batteries (for transmitter)

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS

Your new Horizon Hobby vehicle has been designed and built with a combination of waterproof and water-resistant components to allow you to operate the product in many "wet conditions," including puddles, creeks, wet grass, snow and even rain.
While the entire vehicle is highly water-resistant, it is not completely waterproof and your vehicle should NOT be treated like a submarine. The various electronic components used in the vehicle, such as the Electronic Speed Control (ESC), servo(s) and receiver are waterproof, however, most of the mechanical components are water-resistant and should not be submerged.
Metal parts, including the bearings, hinge pins, screws and nuts, as well as the contacts in the electrical cables, will be susceptible to corrosion if additional maintenance is not performed after running in wet conditions. To maximize the long-term performance of your vehicle and to keep the warranty intact, the procedures described in the "Wet Conditions Maintenance" section below must be performed regularly if you choose to run in wet conditions. If you are not willing to perform the additional care and maintenance required, then you should not operate the vehicle in those conditions.
CAUTION: Failure to exercise caution while using this product and complying with the following precautions could result in product malfunction and/or void the warranty.
GENERAL PRECAUTIONS
· Read through the wet conditions maintenance procedures and make sure that you have all the tools you will need to properly maintain your vehicle.
· Not all batteries can be used in wet conditions. Consult the battery manufacturer before use. Caution should be taken when using Li-Po batteries in wet conditions.
· Most transmitters are not water-resistant. Consult your transmitter's manual or the manufacturer before operation.
· Never operate your transmitter or vehicle where lightning may be present. · Do not operate your vehicle where it could come in contact with salt
water (ocean water or water on salt-covered roads), contaminated or polluted water. Salt water is very conductive and highly corrosive, so use caution.

· Even minimal water contact can reduce the life of your motor if it has not been certified as water-resistant or waterproof. If the motor becomes excessively wet, apply very light throttle until the water is mostly removed from the motor. Running a wet motor at high speeds may rapidly damage the motor.
· Driving in wet conditions can reduce the life of the motor. The additional resistance of operating in water causes excess strain. Alter the gear ratio by using a smaller pinion or larger spur gear. This will increase torque (and motor life) when running in mud, deeper puddles, or any wet conditions that will increase the load on the motor for an extended period of time.
WET CONDITIONS MAINTENANCE
· Drain any water that has collected in the tires by spinning them at high speed. With the body removed, place the vehicle upside down and pull full throttle for a few short bursts until the water has been removed.
CAUTION: Always keep hands, fingers, tools and any loose or hanging objects away from rotating parts when performing the above drying technique.
· Remove the battery pack(s) and dry the contacts. If you have an air compressor or a can of compressed air, blow out any water that may be inside the recessed connector housing.
· Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off with a garden hose. Avoid rinsing the bearings and transmission.
NOTICE: Never use a pressure washer to clean your vehicle.
· Use an air compressor or a can of compressed air to dry the vehicle and help remove any water that may have gotten into small crevices or corners.
· Spray the bearings, drive train, fasteners and other metal parts with a water-displacing light oil. Do not spray the motor.
· Let the vehicle air dry before you store it. Water (and oil) may continue to drip for a few hours.
· Increase the frequency of disassembly, inspection and lubrication of the following: - Front and rear axle hub assembly bearings. - All transmission cases, gears and differentials. - Motor--clean with an aerosol motor cleaner and re-oil the bushings with lightweight motor oil.

QUICK START

Please read the entire manual to gain a full understanding of the Axial Ryft RTR vehicle, fine-tuning the setup and performing maintenance.

1. Read the safety precautions found in this manual. 2. Charge a battery for the vehicle. Refer to the included charging warnings
and instructions for battery charging information. 3. Install the AA batteries in the transmitter. Only use alkaline or
rechargeable batteries. 4. Install the fully charged battery in the vehicle.

5. Power ON the transmitter and then the vehicle. Wait 5 seconds for the ESC to initialize. Always power the transmitter ON before the vehicle and power it OFF after the vehicle has been powered OFF.
6. Check the steering and throttle control directions. Verify that the servos are moving in the correct direction.
7. Drive your vehicle.
8. Perform any necessary maintenance.

INSTRUCTION MANUAL

CHARGING THE BATTERY

Choose a battery designed to work with the SpektrumTM FirmaTM SMART 130A Brushless ESC (SPMXSE1130). We recommend the Spektrum 5000mAh 3S 11.1V 50C Smart LiPo Battery (SPMX50003S50H5) or the Spektrum 5000mAh 4S 14.8V 50C Smart LiPo Battery (SPMX50004S50H5) hardcase batteries with IC5® connector. Choose a charger designed to charge 3S and/or 4S Li-Po batteries.

We recommend the Spektrum SMART S1100 AC Charger, 1x100W (SPMXC1080). Refer to your battery and charger manuals for usage, safety, and charging information.

INSTALLING THE TRANSMITTER BATTERIES
This transmitter requires 4 AA batteries. 1. Remove the battery cover from the transmitter. 2. Install the batteries as shown. 3. Install the battery cover.
CAUTION: If using rechargeable batteries, charge only rechargeable batteries. Charging non-rechargeable batteries may cause the batteries to burst, resulting in injury to persons and/or damage to property.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to national regulations.

TRANSMITTER FUNCTIONS
A/B. CHANNEL 3 BUTTON
C. THROTTLE/BRAKE
D. STEERING WHEEL
E. STEERING RATE Adjusts the end point of the steering
F. BRAKE RATE Adjusts the braking end point.
G. STEERING TRIM Adjusts the steering center point. Normally, the steering trim is adjusted until the vehicle tracks straight.
H. THROTTLE TRIM Adjusts the throttle neutral point
I. SMART BATTERY LEVEL INDICATOR
J. SERVO REVERSING To reverse the Throttle (TH) or Steering (ST) channel, switch the position of the correlating switch--"N" is for normal, "R" is for reverse.
K. THROTTLE LIMIT Limits throttle output to 50/75/100% Select 50% or 75% for less experienced drivers or when you are driving the vehicle in a small area.
L. POWER LED · Solid red lights: Indicates radio connectivity and adequate battery power · Flashing red lights: Indicates the battery voltage is critically low. Replace batteries
M. POWER BUTTON
N. BIND BUTTON

I J K L
M N
A/B

H G F E
D C

RBX10 RYFT ROCK BOUNCER, 1/10 RTR

SR6100AT AVC TECHNOLOGY TELEMTRY RECEIVER

Battery/Programming Port
Steering Port Throttle Port
AUX 1 Port AUX 2 Port AUX 3 Port AUX 4 Port

Bind Button

AUX CHANNELS
The Aux channels can operate as additional servo channels, or as a power supply for a personal transponder.
If AVC is active, only 4 channels; Steering, Throttle, AUX3 and AUX4 are operational. The remaining Aux channels can be used to power a personal transponder or lights.
If AVC is disabled (see DISABLING AVC TECHNOLOGY STABILITY ASSIST FUNCTION), all 6 channels including the Aux channels can operate as servo channels.

INSTALLING THE VEHICLE BATTERY
1. Ensure the ESC is powered OFF. 2. Remove the body clips and rotate the hood up. 3. Insert the battery into the battery tray. 4. Install the battery straps to hold the battery in place. 5. Connect the battery power lead to the ESC IC5 connector, noting proper
polarity. 6. Power ON the transmitter, then the vehicle. 7. Rotate the body into place, and insert the body clips.
IMPORTANT: Secure the ESC wires so they do not interfere with any moving parts.

BINDING AND CALIBRATING THE RECEIVER
Binding is the process of linking the SR6100AT receiver to your Spektrum transmitter. The AVC features on the receiver can be enabled or disabled during the binding process.
IMPORTANT: You must calibrate the SR6100AT receiver each time it is placed in bind mode, regardless of AVC being enabled or disabled.
Upon initial setup after the first bind, the model must be configured for servo direction, trim and travel. Then the receiver must be rebound and calibrated to those settings for proper operation. Center the steering trim and throttle trim on the transmitter before beginning.
1. Press and hold the bind button on the receiver. 2. Power on the receiver. The orange LED flashes, indicating the receiver is
in bind mode. Release the bind button after the orange LED illuminates. 3. Put your transmitter in bind mode. The bind process is complete when
the orange LED on the receiver remains lit. The receiver is now bound to the transmitter but must be calibrated before it will operate.

Full Throttle

Brake/Reverse

4. Pull the transmitter trigger to full throttle, pause, then return the trigger to center.
5. Push the transmitter trigger to full brake, pause, then return the trigger to center.
6. Turn the transmitter steering wheel to full right, pause, then return the wheel to center.
7. Turn the transmitter steering wheel to full left, pause, then return the steering wheel to center. The orange LED flashes to confirm the settings have been accepted.
8. Turn off the vehicle to complete the binding and calibration process.

CAUTION: When the bind process is complete, the throttle and steering channels are active. Keep hands and loose objects away from all spinning parts on the vehicle.
IMPORTANT: You must rebind the transmitter and receiver if you:
· Change the servo reversing after binding · Change the travel after binding · Change the receiver mounting orientation
DISABLING AVC® TECHNOLOGY STABILITY ASSIST
If you participate in organized racing, you may be required to turn AVC technology off. To turn off AVC technology: 1. Connect power to the receiver and quickly press and release the bind
button three times (within 1.5 seconds). 2. Press and hold the bind button and to put the receiver in bind mode.
release the buton when the LED starts to flash rapidly, indicating it is in bind mode. When the AVC system has been disabled, the LED on the receiver will show three flashes upon power up, and then remain lit. The receiver is bound and operating normally when the LED remains illuminated.
TIP: If the AVC feature in the receiver is active and the AVC menu in the transmitter is Inhibited, AVC functions will default to the AUX 1 and AUX 2 operation, and in this scenario, AVC will not work correctly.
FAILSAFE
In the unlikely event that the radio link is lost during use, the receiver will drive the throttle channel to the neutral position. If the receiver is powered on prior to turning on the transmitter, the receiver will enter the failsafe mode, driving the throttle channel to the neutral position. When the transmitter is turned on, normal control is resumed.
IMPORTANT: Failsafe activates only in the event that signal is lost from the transmitter. Failsafe will NOT activate in the event that receiver battery power decreases below the recommended minimums or power to the receiver is lost.

INSTRUCTION MANUAL

DRIVING PRECAUTIONS

· Maintain sight of the vehicle at all times. · Routinely inspect the vehicle for loose wheel hardware. · Routinely inspect the steering assembly for any loose hardware. Driving
the vehicle off-road can cause fasteners to loosen over time. · Do not drive the vehicle in tall grass. Doing so can damage the vehicle or
electronics. · Stop driving the vehicle when you notice a lack of power. Driving the vehicle
when the battery is discharged can cause the receiver to power off. If the receiver loses power, you will lose control of the vehicle. Damage due to an over-discharged Li-Po battery is not covered under warranty.

CAUTION: Do not discharge a Li-Po battery below 3V per cell. Batteries discharged to a voltage lower than the lowest approved voltage may become damaged, resulting in loss of performance and potential fire when batteries are charged.
· Do not apply forward or reverse throttle if the vehicle is stuck. Applying throttle in this instance can damage the motor or ESC.
· After driving the vehicle, allow the electronics to cool before driving the vehicle again.
IMPORTANT: Keep wires away from all moving parts.

POWERING ON THE VEHICLE
1. Center the ST TRIM and TH TRIM dials on the transmitter. 2. Power on the transmitter. 3. Install a fully charged battery pack per the Installing the Battery section. 4. Power on the ESC.
BEFORE RUNNING YOUR VEHICLE
1. Check for free suspension movement. All suspension arms and steering components should move freely. Any binds will cause the vehicle to handle poorly.
TIP: To increase the ride height and ground clearance of your vehicle, screw down the shock collars to compress the springs.
2. Charge a battery pack. Always charge the battery pack as per the battery and/or charger manufacturers' instructions.
3. Set the transmitter steering trim. Follow the instructions to set the steering trim/subtrim so that the vehicle drives straight with no input to the steering.
4. Perform a Control Direction Test.

IMPORTANT: The vehicle MUST remain on a flat, level surface and motionless for at least 5 seconds.

AVC SENSITIVITY
The ST RATE dial adjusts the sensitivity, or stability, value in the receiver. If you increase the sensitivity, the AVC® system becomes more sensitive to the vehicle drifting left or right. You would use maximum sensitivity during
high speed driving or drag racing, when you want the vehicle to stay in a straight line.
Turn the ST RATE knob counter-clockwise to reduce the sensitivity.
Turn the ST RATE knob clockwise to increase the sensitivity.

IMPORTANT: The ST RATE knob will only adjust the sensitivity when the transmitter is bound to a DSMR® receiver. When the transmitter is bound to a DSM®, DSM2® or DSM Marine receiver, the ST RATE knob controls the steering dual rate.

RUN TIME
The largest factor in run time is the capacity of the battery pack. A larger mAh rating increases the amount of run time experienced.
The condition of a battery pack is also an important factor in both run time and speed. The battery connectors may become hot during driving. Batteries will lose performance and capacity over time.
Driving the vehicle from a stop to full speed repeatedly will damage the batteries and electronics over time. Sudden acceleration will also lead to shorter run times.

TO IMPROVE RUN TIMES
· Keep your vehicle clean and well maintained. · Allow more airflow to the ESC and motor. · Change the gearing to a lower ratio. A lower ratio decreases the operating
temperature of the electronics. Use a smaller pinion gear or larger spur gear to lower the gear ratio. · Use a battery pack with a higher mAh rating. · Use the optimum charger to charge battery packs (Visit your local hobby dealer for more information).

PERFORMING A CONTROL DIRECTION TEST
Perform a control test with the vehicle wheels off the ground. If the wheels rotate after the vehicle is powered ON, adjust the TH Trim knob until they stop. To make the wheels move forward, pull the trigger. To reverse them, wait for the wheels to stop, then push the trigger. When moving forward, the wheels should maintain a straight line without any steering wheel input. If not, adjust the ST Trim knob, so the wheels maintain a straight line without having to turn the steering wheel.

RBX10 RYFT ROCK BOUNCER, 1/10 RTR

CHANGING THE TRAVEL ADJUST SETTINGS
Set the travel adjust settings with all four vehicle wheels off the ground. The throttle end point and brake end point adjustments will cause the wheels to spin at full speed. Have an assistant safely hold the vehicle securely while adjusting these settings.
CAUTION: Keep hands, hair and all loose clothing away from any moving parts, especially the wheels, while setting the travel adjust end points. Serious injury may result.
1. Hold the trigger in the full brake position and turn the steering wheel to full right while powering on the transmitter. The LED flashes rapidly, indicating programming mode is active.
2. Throttle End Point: Continue holding full throttle. Turn the TH TRIM knob to adjust the full throttle end point.

VEHICLE FLUIDS

The Axial Ryft comes from the factory with the following lubricants:

Shock Oil Differential Fluid Transmission Gears

30 wt 1,000,000 wt Hi Pressure Black Grease

EN
3. Brake End Point: Hold the trigger in the full brake position. Turn the TH TRIM knob to adjust the full brake end point. Return the trigger to the center position.
4. Left Steering End Point: Hold the steering wheel in the full left position. Turn the ST TRIM knob to adjust the left end point.
5. Right Steering End Point: Hold the steering wheel in the full right position. Turn the ST TRIM knob to adjust the right end point. Return the steering wheel to the center position.
6. Power off the transmitter to save the travel adjust settings. The minimum Travel is 75%, and the Maximum travel is 150%.
IMPORTANT: If the travel is changed on the DX3, you must rebind and calibrate the SRS6100AT.

SPEKTRUMTM FIRMATM SMART 130A BRUSHLESS ESC

SPECIFICATIONS

Type

Sensorless, SMART Throttle Compatible

Output

130A/760A

Function

Forward/BrakeForward/Brake Reverse

Input Voltage

7.4V14.8V

BEC Output

6V/4A

Dimensions (LxWxH) 57.5mm x 46mm x 38mm

Weight

154 g

ESC LED STATUS
· No ESC LEDs will glow when there is no throttle input from the transmitter. · The red ESC LED glows when there is any throttle input from the transmitter.
AUDIBLE WARNING TONES
1. Input Voltage: The ESC checks the input voltage when it is powered ON. If a voltage problem is detected, the ESC continuously sounds 2 beeps with a 1 second pause (xx-xx-xx). Power OFF the ESC and ensure the connections are secure and that the battery power is not too low for safe operation.
2. Radio Connection: The ESC checks radio signal input when it is powered ON. If a problem is detected, the ESC continuously sounds 1 beep with a 2 second pause (x--x--x). Power OFF the ESC and ensure the radio system is operating correctly.
NOTICE: Always disconnect the battery from the ESC after operating your vehicle. The ESC's switch only controls power to the receiver and servos. The ESC will continue to draw current when connected to the battery, resulting in possible damage to the battery through over discharge.

ESC CALIBRATION PROCEDURE
Complete the transmitter/receiver binding procedure prior to calibrating the ESC.
1. Set the transmitter throttle channel to 100% travel and center the throttle trim. 2. Connect a battery to the ESC battery lead. 3. Power on the transmitter. 4. Press and hold the SET button while turning on the ESC. Release the
SET button when the red LED begins to flash, indicating the ESC is in calibration mode. The ESC will enter programming mode if the button is held for more than three seconds.
TIP: The red LED should be flashing when the ESC enters calibration mode. If the green LED is flashing the ESC has entered programming mode. Power off the ESC and repeat step 4, releasing the SET button when the red LED begins to flash.
5. With the transmitter throttle trigger at the neutral position, press and release the ESC SET button. The red LED will stop flashing, the green LED will flash one time and the motor will make a tone to indicate the neutral position has been accepted.
6. While holding the throttle trigger at the full throttle position, press and release the ESC SET button. The green LED will flash twice and the motor will make two tones to indicate the full throttle position has been accepted.
7. While holding the throttle trigger at the full brake position, press and release the SET button. The green LED will flash three times and the motor will make three tones to indicate the full brake position has been accepted.
The motor will operate normally after calibration is completed.

INSTRUCTION MANUAL

EN
ESC FUNCTIONS AND MODES The ESC includes programming options so you can adjust the way your vehicle performs. Refer to the included programming table to adjust the ESC for your driving conditions.

PROGRAMMING TABLE

Programming Items 1. Running Mode 2. Drag Brake Force 3. Low Voltage Cutoff 4. Start Mode 5. Max Brake Force 6. Max Reverse Force 7. Initial Brake Force 8. Neutral Range 9. Timing 10. Motor Rotation 11. Li-Po Cells

Programming Value

Forward w/ brake Forward/Reverse w/ brake Forward/Reverse

10%

20%

non-protection

2.6V/Cell

2.8V/Cell 3.0V/Cell

Level 1

Level 2

Level 3

Level 4

25%

50%

75%

100%

25% = Drag Brake 6% (Narrow)
0.00º

50% 0% 9% (Normal) 3.75º

75% 20% 12% (Wide) 7.50º

100% 40%
11.25º

Counterclockwise

Clockwise

Auto Calculate

2 Cells

3 Cells

4 Cells

5 40% 3.2V/Cell Level 5 disable
15.00º 5 Cells

6 60% 3.4V/Cell Level 6
18.75º 6 Cells

Default Settings

80% 100%

Level 7 Level 8 Level 9

22.50º 26.25º

DESCRIPTIONS
1. Running Mode Forward Only with Brake Intended for competition use, this mode allows only forward and brake controls.
Forward/Reverse with Brake This mode is the basic all-around mode, allowing forward, reverse and brake controls. To engage reverse while moving forward, apply the brake until the vehicle has come to a complete stop, release brake, then apply the brake again. While braking or in reverse, engaging the throttle will result in the vehicle immediately accelerating forward.
2. Drag Brake Force Adjusts the amount of brake automatically applied when the throttle is returned to the neutral position. This simulates the engine braking effect of a full-scale vehicle, allowing improved turn-in and your vehicle's general response to controls.
3. Low Voltage Cutoff This function helps to prevent battery over-discharge. The ESC continuously monitors the battery's voltage. If the voltage falls below the voltage threshold for 2 seconds, the output power shuts off and the red LED flashes twice repeatedly.
The cutoff threshold calculation is based on individual Li-Po cell voltage. For Ni-MH batteries, if the voltage battery pack is higher than 9.0V, it will be treated as a 3-cell Li-Po battery pack; if it is lower than 9.0V, it will be treated as a 2-cell Li-Po battery pack. Example: for a 8.0V Ni-MH battery pack used with a 2.6V/cell threshold, it will be treated as a 2-cell Li-Po battery pack and the low-voltage cut-off threshold will be 5.2V (2.6x2=5.2).
4. Start Mode (Punch) Sets the initial throttle punch when the car accelerates. Level 1 gives a very soft initial acceleration and level 4 gives a stronger initial acceleration.

5. Max Brake Force Adjusts the maximum braking force. A higher value provides stronger braking, but can also cause the wheels to lock, resulting in loss of control of the car.
6. Max Reverse Force This parameter adjusts the maximum power when travelling in reverse.
7. Initial Brake Force (minimum brake) Adjusts the minimum amount of braking power when the brakes engage. The default value is equal to the drag brake value. A high value can lock the wheels when the brake is used.
8. Neutral Range Adjusts the throttle sensitivity around the neutral point. A higher value results in the throttle having to be moved more for the vehicle to move forward, backward or brake.
9. Timing Adjusts the motor drive current timing. More timing gives more performance, but can lower efficiency and cause damage to the motor and/or ESC by overload or overheating.
NOTICE: Always ensure the motor timing is set correctly. Failure to set the motor timing correctly can result in damage to the motor and ESC. Refer to the manufacturer instructions for recommended timing settings.
10. Motor Type 11. Motor Rotation
Allows you to make this change in the ESC so no wires need to be changed between the ESC and the motor.
12. Li-Po Cells Allows the ESC to automatically detect or manually set the number of cells in your Li-Po battery back.

ESC PROGRAMMING PROCEDURE
Programming is accomplished using the SET button on the ON/OFF switch*.
1. Connect a fully charged battery to the ESC. 2. Power on the transmitter. 3. Power on the ESC. 4. Hold the SET button until the green LED flashes. Release the set button
to enter programming mode.
TIP: To reset all programming items to the default values, press and hold the set button for five seconds
5. Press and release the set button as needed to cycle through the programming items. The number of times the green LED flashes equals the programming item number given in the programming table

6. When at the desired programming item, press and hold the set button until the red LED flashes to select the item.
7. Press and release the SET button to cycle through the values available for the programming item based on the number of times the LED flashes. Refer to the programming table.
8. Save the setting by pressing and holding the SET button for 3 seconds.
9. Power off the ESC to exit programming mode or to change other programming items.
* Other programming options include the Spektrum SMART Firma ESC Programming Box (SPMXCA200) and the SmartLink USB updating and programmer application. See SpektrumRC.com for more details about Spektrum SMART Firma ESCs.

RBX10 RYFT ROCK BOUNCER, 1/10 RTR

SPEKTRUMTM FIRMATM 2200Kv 4-POLE BRUSHLESS MOTOR

PRECAUTIONS
· Never touch moving parts. · Never disassemble while the batteries are installed. · Always let parts cool before touching.
GEARING
Your vehicle has been equipped with the optimal gearing installed for the use of a 3 or 4S battery. It offers an ideal balance between speed, power and efficiency.
Installing a pinion gear with fewer teeth or a spur gear with more teeth will provide greater torque but will reduce top speed. Likewise, a pinion gear with more teeth or a spur gear with fewer teeth will reduce torque and increase top speed. Care should be taken when installing larger pinion gears as this can "overgear" the vehicle, resulting in overheating of the motor and ESC. When testing different gearing options, pay close attention to the temperature of the motor and speed control to ensure you are operating within the temperature range of the components. The motor or ESC should never be so hot that it cannot be touched. If temperatures are too hot, a different gearing combination with a lower pinion gear and/or higher spur gear is suggested.

Adjusting the gear mesh is only necessary when changing gears.
1. Remove the right body side panel.
2. Remove the gear cover.
3. Remove the two screws holding the motor to the mount.
4. With your chosen gear installed on the motor shaft, select the pair of motor mounting holes which allow for the tightest gear mesh without having to force the gears together or forcing the motor holes to line up with the mount.
5. Install the two motor mounting screws and washers. There should be just enough space between the pinion and spur gears that a small piece of paper can be rotated between the gears easily. If the paper is difficult to rotate into the gears, remove the mounting screws and rotate the motor to the next set of mounting holes. Re-install the mounting screws.

SETTING THE GEAR MESH Proper gear mesh (how gear teeth meet) is important to the performance of the vehicle. When the gear mesh is too loose, the spur gear could be damaged by the pinion gear of the motor. If the mesh is too tight, speed could be limited and the motor and ESC will overheat. The pinion gear setscrew can be accessed by rotating the motor until the setscrew lines up with the notch in the side of the motor mount. The gear mesh has already been set at the factory and is adjusted by rotating the motor mounting screw hole locations. When using the stock pinion and spur gear sizes, the motor mounting screws should be in the mounting holes shown in the illustration to maintain proper gear mesh.
Stock motor mount holes

6. Remove the paper. Check the mesh at 35 different locations around the spur gear for a small amount of movement.
7. Install the gear cover.
TELEMETRY SETTINGS
If using the Spektrum Dashboard app or the optional speedometer module on your transmitter, set the motor pole count to 4 and the rollout distance to 1.57" (39.9mm).

TROUBLESHOOTING GUIDE

Problem Vehicle does not operate
Motor runs but wheels do not rotate

Possible Cause Battery not charged or plugged in ESC switch not "On" Transmitter not "On" or low battery Pinion not meshing with spur gear Pinion spinning on motor shaft Transmission gears stripped Drive pin broken

Steering does not work

Servo plug not in receiver properly

Servo gears or motor damaged

Will not turn one direction Servo gears damaged

Motor wire solder joint is damaged

Motor does not run

Motor wire broken

ESC damaged

ESC gets hot

Motor over-geared Driveline bound up

Poor run time and/or sluggish acceleration

Battery pack not fully charged Charger not allowing full charge Driveline bound up

Transmitter batteries low

Poor range and/or glitching Vehicle battery low

Loose plugs or wires

Solution Charge battery/plug in Turn on ESC switch Turn on/replace batteries Adjust pinion/spur mesh Tighten pinion gear setscrew on motor shaft flat spot Replace transmission gears Check and replace drive pin Make sure the steering servo plug is connected to the receiver steering channel, noting proper polarity Replace or repair servo Replace or repair servo Resolder the motor wire with the proper equipment Repair or replace as needed Contact Horizon Hobby Product Support Use smaller pinion or larger spur gear Check wheels and transmission for binding Recharge battery Try another charger Check wheels, transmission for binding Check and replace Recharge battery Check all wire connections and plugs

INSTRUCTION MANUAL

LIMITED WARRANTY
What this Warranty Covers Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the "Product") will be free from defects in materials and workmanship for a period of 2 years from the date of purchase.
What is Not Covered This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modification of or to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable technical regulations or (vii) use that violates any applicable laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER'S INTENDED USE.
Purchaser's Remedy Horizon's sole obligation and purchaser's sole and exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER'S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, purchaser is advised to return the Product immediately in new and unused condition to the place of purchase.
Law These terms are governed by Illinois law (without regard to conflict of law principals). This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice.
Warranty Services Questions, Assistance, and Services Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup or use of the Product has been started, you must contact your local distributor or Horizon directly. This will

enable Horizon to better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll free telephone number referenced in the Warranty and Service Contact Information section to speak with a Product Support representative.
Inspection or Services If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at http://www.horizonhobby.com/content/ service-center_render-service-center. If you do not have internet access, please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service. When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours. When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.
NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue with a Li-Po battery, please contact the appropriate Horizon Product Support office.
Warranty Requirements For Warranty consideration, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your Product will be serviced or replaced free of charge. Service or replacement decisions are at the sole discretion of Horizon.
Non-Warranty Service Should your service not be covered by warranty, service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of the retail purchase cost. By submitting the item for service you are agreeing to payment of the service without notification. Service estimates are available upon request. You must include this request with your item submitted for service. Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and cashier's checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon's Terms and Conditions found on our website http://www. horizonhobby.com/content/service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the country of use and ownership. If received, a non-compliant Product will not be serviced. Further, the sender will be responsible for arranging return shipment of the un-serviced Product, through a carrier of the sender's choice and at the sender's expense. Horizon will hold non-compliant Product for a period of 60 days from notification, after which it will be discarded.
10/15

WARRANTY AND SERVICE CONTACT INFORMATION

Country of Purchase

Horizon Hobby

Contact Information

Address

Horizon Service Center (Repairs and Repair Requests) servicecenter.horizonhobby.com/RequestForm/

United States of America

Horizon Product Support (Product Technical Assistance)

productsupport@horizonhobby.com 877-504-0233

Sales

websales@horizonhobby.com 800-338-4639

2904 Research Rd. Champaign, Illinois, 61822 USA

European Union

Horizon Technischer Service Sales: Horizon Hobby GmbH

service@horizonhobby.eu +49 (0) 4121 2655 100

Hanskampring 9 D 22885 Barsbüttel, Germany

RBX10 RYFT ROCK BOUNCER, 1/10 RTR

FCC INFORMATION
Contains FCC ID: BRWKATY1T FCC ID: BRWSR6100A This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and/or antenna and your body (excluding fingers, hands, wrists, ankles and feet). This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
SUPPLIER'S DECLARATION OF CONFORMITY
Axial RBX10 Ryft Rock Bouncer RTR (AXI03005) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help.
Horizon Hobby, LLC 2904 Research Rd., Champaign, IL 61822 Email: compliance@horizonhobby.com Web: HorizonHobby.com

IC INFORMATION
CAN ICES-3 (B)/NMB-3(B) Contains IC: 6157A-KATY1T IC: 6157A-SR6100AT This device contains license-exempt transmitter(s)/receivers(s) that comply with Innovation, Science, and Economic Development Canada's licenseexempt RSS(s). Operation is subject to the following 2 conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

COMPLIANCE INFORMATION FOR THE EUROPEAN UNION

EU COMPLIANCE STATEMENT:
Axial RBX10 Ryft Rock Bouncer RTR (AXI03005); Hereby, Horizon Hobby, LLC declares that the device is in compliance with the following: EU Radio Equipment Directive 2014/53/EU; RoHS 2 Directive 2011/65/EU; RoHS 3 Directive - Amending 2011/65/EU Annex II 2015/863.
The full text of the EU declaration of conformity is available at the following internet address: https://www.horizonhobby.com/content/support-rendercompliance.
NOTE: This product contains batteries that are covered under the 2006/66/ EC European Directive, which cannot be disposed of with normal household waste. Please follow local regulations.
Wireless Frequency Range and Wireless Output Power: Transmitter 2402 2478 MHz 17.5dBm Receiver 2405 2478 MHz 19.39dBm

EU Manufacturer of Record: Horizon Hobby, LLC 2904 Research Road Champaign, IL 61822 USA
EU Importer of Record: Horizon Hobby, GmbH Hanskampring 9 22885 Barsbüttel Germany
WEEE NOTICE:
This appliance is labeled in accordance with European Directive 2012/19/EU concerning waste of electrical and electronic equipment (WEEE). This label indicates that this product should not be disposed of with household waste. It should be deposited at an appropriate facility to enable recovery and recycling.

INSTRUCTION MANUAL

REPLACEMENT PARTS // TEILELISTE // LISTE DES PIÈCES DE RECHANGE // ELENCO DEI RICAMBI

Part #

English

ARAC9830 AR709003 Washer 3x8x0.5mm (10)

AXI230032 Body Panel Set (Clear): RBX10

AXI230033 AXI230034 AXI231025 AXI231026 AXI231027 AXI231028 AXI231029 AXI231030 AXI231031 AXI231032 AXI231033 AXI231034 AXI231035 AXI231036 AXI232039 AXI232040 AXI232041 AXI232042 AXI232043

Interior Set (Clear): RBX10 Hook & Loop Strap 17 x 270mm Chassis Skid Plate: RBX10 Servo Saver: RBX10 Cage Sides, L R (Org): RBX10 Cage Roof, Hood (Orange): RBX10 Cge Sprts, Btt Try (Org): RBX10 Cage Fuel Cell (Orange): RBX10 Cge Rdo Bx, Spr Cvr (Org): RBX10 Cage Sides, L R (Blk): RBX10 Cage Roof, Hood (Black): RBX10 Cge Sprts, Btt Try (Blk): RBX10 Cage Fuel Cell (Black): RBX10 Cge Rdo Bx, Spr Cvr (Blk): RBX10 AR14B Axle Housing Front: RBX10 AR14B C-Hub: RBX10 AR14B Steering Knuckle: RBX10 AR14B Metal Diff Cover: RBX10 AR14B Unvrsl Axle Set: RBX10

AXI232045 Hex Rtr Clpr Pin Set (4): RBX10

AXI232047 AXI232049 AXI232050 AXI232051 AXI232052 AXI232053 AXI232054 AXI232055 AXI232056 AXI232057 AXI232058 AXI233020 AXI233021 AXI233023 AXI233024 AXI233025 AXI233026 AXI233027 AXI233028 AXI233029 AXI233030 AXI234020 AXI234021 AXI234022 AXI234023 AXI234024 AXI234025 AXI234026 AXI234027 AXI234028 AXI234029 AXI234030 AXI235097 AXI235109 AXI235110 AXI235167 AXI235168 AXI235329 AXI236103 AXI236174 AXI43002 AXI43011

AR14B Axle Housing Rear: RBX10 AR14B Straight Axle (2): RBX10 Transmission Housing Set: RBX10 WB11 Driveshaft Set: RBX10 WB11 Driveshaft Cplr (2): RBX10 Diff, Gears, Housing: RBX10 Ring 38T, Pinion 13T, 32P: RBX10 Spur Gear, 53T 32P: RBX10 Transmissoin, Motor Plate: RBX10 Transmission, Shaft Set: RBX10 Trans, Gears, (Hi Speed): RBX10 Shock Parts, Molded: RBX10 Shock Parts Bump Stop (4): RBX10 Shck Bdy, Cap 10x53.5 (2): RBX10 Shock Shaft, 66.7mm (2): RBX10 Shck Bdy, Cap 10x59.5 (2): RBX10 Shock Shaft, 77.7mm (2): RBX10 Spring 15x85mm 2.20lbs/in (2) Spring 15x105mm 1.75lbs/in (2) O-Ring, Shock Set: RBX10" O-Ring 9x1.9mm (10) SS Steering Links (2): RBX10 SS Link M6 x 114mm (2): RBX10 SS Link M6 x 105mm (2): RBX10 Rear Trailing Arm (2): RBX10 SS Link M6 x 132.5mm (2): RBX10 Rod Ends, Strght, M4 (10): RBX10 Rod Ends, Angled, M4 (10): RBX10 Pvt Ball 3x6.8x9.5mm (10):RBX10 Pivot Ball, 8x7mm (10): RBX10 Pvt Ball,3x6.8x7.6mm(10):RBX10 Pvt Ball,3x6.8x7.5mm (10):RBX10 M2.5 x 6mm, BHS (10) M3 x 14mm, Button Head Screw(10) M3 x 16mm, Button Head Screw(10) M2.5 x 8mm Flat Head Screw (10) M2.5 x 10mm Flat Head Screw (10) M3 x 25mm, Set Screw (10)" 2.5 x 4.6 x 0.5mm Washer (10) M3 x 14mm Pin (6) 2.2 Interco TSL Bogger 5.9" (2) 2.2 Raceline Monster Blk

AXIC0005 AXA0113 Hex Skt Butn Hd M3x6mm

AXIC0012 AXA120 Hex Socket Btn Hd M3x25

Deutsch

Français

Italiano

AR709003 Unterlegscheibe 3 x 8 x 0,5 mm (10) AR709003 Rondelle 3 x 8 x 0,5 mm (10)

AR709003 Rondella 3x8x0,5 mm (10)

Karosserieteilesatz (farblos): RBX10

Ensemble de panneaux de carrosserie (transparent) : RBX10

Pannelli carroz. (trasparenti): RBX10

Innensatz (farblos): RBX10

Ensemble intérieur (transparent) : RBX10 Set interni (trasparenti): RBX10

Klettverschluss 17 x 270 mm

Sangle autoagrippante 17 x 270 mm

Fascetta a strappo 17 x 270 mm

Gleitplatte Fahrwerk: RBX10

Plaque de protection pour châssis : RBX10 Prot. sottoscocca telaio: RBX10

Servo Saver: RBX10

Économiseur de servo : RBX10

Salva servo: RBX10

Käfigseiten, L R (Orange): RBX10

Côtés de cage, D G (orange) : RBX10

Scocca lat, DX/SX (aranc): RBX10

Käfigdach, Haube (Orange): RBX10

Cage, toit, capot (orange) : RBX10

Scoc tetto, cofano (aranc): RBX10

Käfig Sport, Akkufach (Orange): RBX10

Supports de cage, support de batterie (orange) Sup scoc, portabatt (aranc): RBX10

Brennstoffzelle, Käfig (Orange): RBX10

Pile à combustible cage (orange) : RBX10 Scocca, cella carb (aranc): RBX10

Käfig, Funkbox, Halterungsabdeckung (Orange): RBX10 Cage, boîte radio, cache support (orange) : RBX10 Scocca, vano radio, carter supp (aranc)

Käfigseiten, L R (Schwarz): RBX10

Côtés de cage, D G (noir) : RBX10

Scocca lat, DX/SX (nero): RBX10

Käfigdach, Haube (Schwarz): RBX10

Cage, toit, capot (noir) : RBX10

Scoc tetto, cofano (nero): RBX10

Käfighalterungen, Akkufach (Schwarz): RBX10 Supports de cage, support de batterie (noir) Sup scoc, portabatt (nero): RBX10

Brennstoffzelle, Käfig (Schwarz): RBX10

Pile à combustible cage (noire) : RBX10

Scocca, cella carb (nero): RBX10

Käfig, Funkbox, Halterungsabdeckung (Schwarz): RBX10 Cage, boîte radio, cache support (noir) : RBX10 Scocca, vano radio, carter supp (nero)

AR14B Achsgehäuse, Front: RBX10

AR14B Carter d'essieu avant : RBX10

AR14B Allogg assale ant: RBX10

AR14B C-Hub: RBX10

AR14B Moyeu de support : RBX10

AR14B Supporto mozzo: RBX10

AR14B Lenkrolle: RBX10

AR14B Rotule de direction : RBX10

AR14B Fuso a snodo: RBX10

AR14B Differentialabdeckung aus Metall: RBX10 AR14B Cache de différentiel métallique

AR14B Carter diff metallo: RBX10

AR14B Universalachsensatz: RBX10

AR14B Ensemble d'essieux universels

AR14B Set assale univ: RBX10

Satz Sechskant, Bremsscheibe, Bremssattel, Ensemble de broches d'étrier de rotor

Stift (4): RBX10

hexagonal (4)

Set perno freno a disco con pinza (4)

AR14B Achsgehäuse, Heck: RBX10

AR14B Carter d'essieu arrière : RBX10

AR14B Allogg assale post: RBX10

AR14B Gerade Achse (2): RBX10

AR14B Essieu droit (2) : RBX10

AR14B Assale dritto (2): RBX10

Getriebegehäusesatz: RBX10

Ensemble de boîte de transmission : RBX10 Kit allogg trasmissione: RBX10

WB11 Antriebswelle-Set: RBX10

WB11 Ensemble d'arbre de transmission WB11 Kit albero trasm: RBX10

WB11 Antriebskupplung (2): RBX10

WB11 Couplage d'arbre de transmission (2) WB11 Acc alber trasm (2): RBX10

Diff., Getriebe, Gehäuse: RBX10

Différentiel, engrenages, boîtier : RBX10 Diff, ingr, allogg: RBX10

Ring 38T, Zahnrad 13T, 32P: RBX10

Anneau 38T, pignon 13T, 32P : RBX10

Corona 38T, Pign 13T, 32P: RBX10

Stirnrad, 53T, 32P: RBX10

Engrenage cylindrique, 53T, 32P : RBX10 Ingr cilindrico, 56T, 32P: RBX10

Getriebemotorplatte: RBX10

Transmission, plaque de moteur : RBX10 Trasm, piastra motore: RBX10

Getriebewellensatz: RBX10

Transmission, ensemble d'arbre : RBX10 Trasm, kit albero: RBX10

Getriebe (Hochgeschwindigkeit): RBX10

Transmission, engrenages (haute vitesse) Trasm, ingr (alta velocità): RBX10

Stoßdämpferteile, gegossen: RBX10

Pièces de l'amortisseur, moulées : RBX10 Parti amm stampate: RBX10

Stoßdämpferteile, Anschlagpuffer (4): RBX10 Butée de pièces d'amortisseur (4) : RBX10 Finecorsa amm (4): RBX10

Schlagfestes Gehäuse, Kappe, 10 x 53,5 (2) Carrosserie d'amortisseur, capuchon 10 x 53,5 (2) Scocca amm, Tappo 10x53.5 (2): RBX10

Kolbenstange, 66,7 mm (2): RBX10

Bras d'amortisseur, 66,7 mm (2) : RBX10 Asta amm, 66,7 mm (2): RBX10

Schlagfestes Gehäuse, Kappe, 10 x 59,5 (2) Corps d'amortisseur, capuchon 10 x 59,5 (2) Scocca amm, Tappo 10x59.5 (2): RBX10

Kolbenstange, 77,7 mm (2): RBX10

Bras d'amortisseur, 77,7 mm (2) : RBX10 Asta amm, 77,7mm (2): RBX10

Feder 15 x 85 mm 2,20 lbs/in (998 g/Zoll) (2) Ressort 15 x 85 mm 0,25 Nm (2)

Molla 15x85 mm 2,20 lb/in (2)

Feder 15 x 105 mm 1,75 lbs/in (794 g/Zoll) (2) Ressort 15 x 105 mm 0,20 Nm (2)

Molla 15x105 mm 1,75 lb/in (2)

O-Ring-Satz für den Stoßdämpfer: RBX10" Joints toriques, ensemble amortisseur : RBX254 mm Kit amm, O-ring: RBX10"

O-Ring 9 x 1,9 mm (10)

Joint torique 9 x 1,9 mm (10)

O-ring 9x1,9 mm (10)

Lenkstangen aus Edelstahl (2): RBX10

Bras de direction en acier inoxydable (2) Tiranti sterzo acc inox (2): RBX10

Verbindung aus Edelstahl M6 x 114 mm (2): RBX10 Bras SS M6 x 114 mm (2) : RBX10

Braccetto accaio inox M6x114 mm (2)

Verbindung aus Edelstahl M6 x 105 mm (2): RBX10 Bras SS M6 x 105 mm (2) : RBX10

Braccetto accaio inox M6x105 mm (2)

Längsträger Heck (2): RBX10

Bras oscillant arrière (2) : RBX10

Braccio post (2): RBX10

Verbindung aus Edelstahl M6 x 132,5 mm (2) Bras SS M6 x 132,5 mm (2) : RBX10

Braccetto accaio inox M6x 132,5 mm (2)

Gelenkköpfe, gerade, M4 (10): RBX10

Embouts de bielle, droits, M4 (10) : RBX10 Teste a snodo dritte M4 (10): RBX10

Gelenkköpfe, abgewinkelt, M4 (10): RBX10 Embouts de bielle, coudés, M4 (10) : RBX10 Teste a snodo angol M4 (10): RBX10

Kugelzapfen 3 x 6,8 x 9,5 mm (10): RBX10 Rotule 3 x 6,8 x 9,5 mm (10) : RBX10

Art rotula 3x6,8x9,5 mm (10): RBX10

Kugelzapfen, 8 x 7 mm (10): RBX10

Rotule, 8 x 7 mm (10) : RBX10

Art rotula, 8x7mm (10): RBX10

Kugelzapfen, 3 x 6,8 x 7,6 mm (10): RBX10 Rotule, 3 x 6,8x 7,6 mm (10) : RBX10

Art rotula 3x6,8x7,6 mm (10): RBX10

Kugelzapfen 3 x 6,8 x 7,5 mm (10): RBX10 Rotule, 3 x 6,8 x 7,5 mm (10) : RBX10

Art rotula 3x6,8x7,5 mm (10): RBX10

M2,5 x 6 mm, Rundkopfschraube (10)

Vis à tête bombée M2,5 x 6 mm (10)

Viti testa tonda M2.5 x 6 mm (10)

M3 x 14 mm, Rundkopfschraube (10)

Vis à tête bombée M3 x 14 mm (10)

Viti testa tonda M3 x 14 mm (10)

M3 x 16 mm, Rundkopfschraube (10)

Vis à tête bombée M3 x 16 mm (10)

Viti testa tonda M3 x 16 mm (10)

M2,5 x 8 mm Flachkopfschraube (10)

Vis à tête plate M2,5 x 8 mm (10)

Viti testa piatta M2.5 x 8 mm (10)

M2,5 x 10 mm Flachkopfschraube (10)

Vis à tête plate M2,5 x 10 mm (10)

Viti testa piatta M2.5 x 10 mm (10)

M3 x 25 mm, Stellschraube (10)"

M3 x 25mm, Vis de fixation (10)

Grani M3 x 25 mm (10)

2,5 x 4,6 x 0,5 mm Unterlegscheibe (10)

Rondelle 2,5 × 4,6 × 0,5 mm (10)

Rondelle 2,5 x 4,6 x 0,5 mm (10)

M3 x 14 mm, Stift (6)

Broche M3 x 14 mm (6)

Perni M3 x 14 mm (6)

2.2 Interco TSL Bogger 5.9" (2)

2.2 Pneu Interco TSL/Bogger 149,86 mm (2) 2.2 Interco TSL Bogger 5.9" (2)

2.2 Raceline Monster, Schwarz

2.2 Raceline Monster noir

2.2 Raceline Monster, nero

AXA0113 Innensechskantschraube, Rundkopf, AXA0113 Douille hexagonale à tête bombée

M3 x 6 mm

AXA0113 Vite cil esag inc M3x6 mm

AXA120 Innensechskantschraube, Rundkopf, M3 x 25 AXA120 Douille hexagonale à tête bombée M3 x 25 AXA120 Vite cil esag inc M3x25

RBX10 RYFT ROCK BOUNCER, 1/10 RTR

Part #

English

Deutsch

Français

Italiano

AXIC0013 AXA013 Cap Hd M2x6mm Blk Oxide AXA013 Kappenkopf M2 x 6 mm, Schwarz, Oxid

AXA013 Vis d'assemblage creuse M2x6mm brunie AXA013 Viti testa tonda M2x6 mm nero ossido

AXIC0014 AXA121 Hex Socket Btn Hd M3x30 AXA121 Innensechskantschraube, Rundkopf, M3 x 30 AXA121 Douille hexagonale à tête bombée M3 x 30 AXA121 Vite cil esag inc M3x30

AXIC0087 AXA087 Cap Hd M3x16mm Blk Oxid AXA087 Kappenkopf M3 x 16 mm, Schwarz, Oxid

AXA087 Vis d'assemblage creuse M3 x 16 mm brunie AXA087 Viti testa tonda M3x16 mm nero ossido

AXIC0114 AXA114 Hex Skt Butn Hd M3x8mm AXA114 Innensechskantschraube, Rundkopf, M3 x 8 mm AXA114 Douille hexagonale à tête bombée M3 x 8 mm AXA114 Vite cil esag inc M3x8 mm

AXIC0115 AXA115 Hex Skt Butn Head M3x10 AXA115 Innensechskantschraube, Rundkopf, M3 x 10 mm AXA115 Douille hexagonale à tête bombée M3 x 10 AXA115 Vite cil esag inc M3x10 mm

AXIC0116

AXA116 Hex Skt Butn Hd M3x12mm

AXA116 Innensechskantschraube, Rundkopf, M3 x 12 mm

AXA116 Douille hexagonale à tête bombée M3 x 12 mm

AXA116 Vite cil esag inc M3x12 mm

AXIC0118 AXA144 Hex Flt Hd M3x8mm Blk10

AXA144 Innensechskantschraube, Flachkopf M3 x 8 mm AXA144 Douille hexagonale à tête plate M3 x 8 mm AXA144 Vite piatta esag M3x8 mm nero

Schwarz 10

noire 10

(10)

AXIC0146 AXA146 Hex Skt Flat Hd M3x12mm AXA146 Innensechskantschraube, Flachkopf, M3 x 12 mm AXA146 Douille hexagonale à tête plate M3 x 12 mm AXA146 Vite piatta esag inc M3x12 mm

AXIC0147 AXA0147 Hex Skt Flt Hd M3x16mm AXA0147 Innensechskantschraube, Flachkopf, M3 x 16 mm AXA0147 Douille hexagonale à tête plate M3 x 16 mm AXA147 Vite cil esag inc M3x16 mm

AXIC0180 AXA180 Set Screw M3x3mm Blk Ox AXA180 Schraubensatz M3 x 3 mm, Schwarz, Oxid AXA180 Vis de fixation M3 x 3 mm brunie AXA180 Grano M3x3 mm nero ossido

AXIC0221 AXA1221 Bearing 5x11x4mm

AXA1221 Lager 5 x 11 x 4 mm

AXA1221 Roulement 5 x 11 x 4 mm

AXA1221 Cuscinetto 5x11x4 mm

AXIC0230 AXA1230 Bearing 10x15x4mm

AXA1230 Lager 10 x 15 x 4 mm

AXA1230 Roulement 10 x 15 x 4 mm

AXA1230 Cuscinetto 10x15x4 mm

AXIC0830 AXA083 Cap Head M3x6mm Blk(10) AXA083 Kappenkopf M3 x 6 mm Schwarz (10) AXA083 Vis d'assemblage creuse M3 x 6 mm noire (10) AXA083 Viti testa tonda M3x6 mm nero (10)

AXIC0843 AX30843 Pinion Gear 32P 17T

AX30843 Zahnradgetriebe 32P 17T

AX30843 Engrenage à pignons 32P 17T

AX30843 Pignone 32P 17T

AXIC1009

AXA0109 Hex Skt Oversize M3x10mm

AXA0109 Innensechskantschraube, Übergröße, AXA0109 Douille hexagonale

M3 x 10 mm

surdimensionnée M3 x 10 mm

AXA0109 Viti oversize esag inc M3x10 mm

AXIC1041 AXA1041 Nylon Locknut 2.5 (10)

AXA1041 Nylon-Feststellmutter 2,5 (10)

AXA1041 Contre-écrou en nylon 2,5 (10) AXA1041 Controdado nylon 2.5 (10)

AXIC1053 AXA1053 Nylon Lock Hex Nut M3 (10) AXA1053 Nylon-Sechskant-Feststellmutter M3 (10) AXA1053 Contre-écrou à six pans en nylon M3 (10) AXA1053 Ctrdado esag nylon M3 (10)

AXIC1119 AX31119 Hex Skt Btn 3x35mm(10)

AX31119 Innensechskantschraube, Rundkopf, AX31119 Douille hexagonale bombée

3 x 35 mm (10)

AX31119 Vite cil esag inc 3x35 mm (10)

AXIC1120 AX31120 Hex Skt Flat 3x10mm(10)

AX31120 Innensechskantschraube, Flachkopf, 3 x 10 mm (10)

AX31120 Douille (10)

hexagonale

plate

3 x 10 mm

AX31120 Vite piatta esag

inc 3x10 mm (10)

AXIC1180

AXA118 Hex Socket BtnHd M3x18mm(10)

AXA118 Innensechskantschraube, Rundkopf, M3 x 18 mm (10)

AXA118 Douille hexagonale à tête bombée M3 x 18 mm (10)

AXA118 Vite cil esag inc M3x18 mm (10)

AXIC1181

AXA119 Hex Socket Btn Hd M3x20(10)

AXA119 Innensechskantschraube, Rundkopf, M3 x 20 (10)

AXA119 Douille hexagonale à tête bombée M3 x 20 (10)

AXA119 Vite cil esag inc M3x20 (10)

AXIC3151

AX31051 Nylon Lock Hex Nut 4mm(10)

AX31051 Nylon-Sechskant-Feststellmutter 4 mm (10)

AX31051 Contre-écrou à six pans en nylon 4 mm (10)

AXA31051 Controdado esag nylon 4 mm (10)

AXIC3231 AX31231 Body Clips 8mm (10)

AX31231 Karosserieklemmen 8 mm (10)

AX31231 Clips de carrosserie 8 mm (10) AX31231 Clip carrozzeria 8 mm (10)

LOS235015 Locknut Flanged M5 Serrated (10) Feststellkontermutter mit Flansch M5 (10) Contre-écrou à embase M5 strié (10)

Controdado flangiato dentellato M5 (10)

LOSA6940 6x12x4mm Sealed Ball Bearing (4) 6 x 12 x 4 mm abgedichtetes Kugellager (4) Roulement à billes hermétique 6 x 12 x 4 mm (4) Cuscinetti a sfera sigill 6x12x4 mm (4)

LOSA6956 12 x 18 x 4mm Ball Bearing (2)

12 x 18 x 4 mm, Kugellager (2)

Roulement à billes 12 x 18 x 4 mm (2)

Cuscinetti a sfera 12x18x4 mm (2)

SPM2340 DX3 SMART DSMR 3CH TX

DX3 SMART DSMR TX mit 3 Kanälen

ÉMETTEUR 3 CANAUX DSMR SMART DX3 TX DX3 SMART DSMR 3 CH

SPMS614S S614S Steel Gear WP Servo, 23T

SS614S Stahlgetriebeservo 23T WP

Servo étanche à engrenages métalliques S614 S614S, servo ingr metallo imp, 23T

SPMSR6100AT SR6100AT 6 Ch AVC/Tele Surf RX

SR6100ATAVC Telemetrie Oberflächenempfänger mit 6 Kanälen

Tele Surf RX/AVC 6 canaux SR6100AT

RX sup SR6100AT 6 Ch AVC/Telem

SPMXSE1130 Firma 130A Brushless Smart ESC

Firma 130 A bürstenloser SmartGeschwindigkeitsregler

Variateur ESC sans balais 130 A Smart Firma Smart ESC Firma 130 A Brushless

SPMXSM2700 FIRMA 2200Kv 4-pole BL Motor

FIRMA 2200 Kv 4-poliger bürstenloser Motor Moteur sans balais à 4 pôles 2 200 Kv FIRMA Motore BL FIRMA 2200 Kv 4 poli

TLR245011 Button Head Screws, M2x6mm (10) Rundkopfschrauben, M2 x 6 mm (10)

Vis à tête bombée, M2 x 6 mm (10)

Viti testa tonda, M2x6 mm (10)

TLR255001 Button Head Screws,M2.5x5mm (10) Rundkopfschrauben, M2,5 x 5 mm (10)

Vis à tête bombée, M2,5 x 5 mm (10)

Viti testa tonda, M2.5x5 mm (10)

TLR5900 Button Hd Screws, M3 x 5mm (10) Rundkopfschrauben, M3 x 5 mm (10)

Vis à tête bombée, M3 x 5mm (10)

Viti testa tonda, M3x5 mm (10)

TLR5907 Button Hd Screws, M3 x 40mm (4) Rundkopfschrauben, M3 x 40 mm (4)

Vis à tête bombée, M3 x 40mm (4)

Viti testa tonda, M3x40 mm (4)

RECOMMENDED PARTS // EMPFOHLENE TEILE// PIÈCES RECOMMANDÉES // PARTI CONSIGLIATE

Part #

English

Deutsch

SPMX50003S50H5 5000mAh 3S 11.1V Smart 50C; IC5 5000 mAh 3S 11,1 V Smart 50C; IC5

SPMX50004S50H5 5000mAh 4S 14.8V Smart 50C; IC5 5000 mAh 4S 14,8 V Smart 50C; IC5

SPMXPS3

Smart PowerStage Bundle 3S

Smart PowerStage-Paket 3S

SPMXPS6

Smart PowerStage Bundle 6S

Smart PowerStage-Paket 6S

Français 5 000 mAh 3S 11,1 V Smart 50C ; IC5 5 000 mAh 4S 14,8 V Smart 50C ; IC5 Ensemble Smart Powerstage 3S Ensemble Smart Powerstage 6S

Italiano 5000 mAh 3S 11,1V Smart 50C IC5 5000 mAh 4S 14,8V Smart 50C IC5 Smart Powerstage Bundle 3S Smart Powerstage Bundle 6S

OPTIONAL PARTS // OPTIONALE TEILE // PIÈCES OPTIONNELLES // PARTI OPZIONALI

Part #

English

Deutsch

Français

Italiano

AXI231007

23T Metal Servo Horn

23T Metall-Servohorn

Renvoi de commande de servo métallique 23T Squad servo, metallo 23T

AXI231012

Servo Horn, Metal 23T: SCX10III

Servohorn, Metall 23T: SCX10III

Renvoi de commande de servo, métallique 23T Squad servo, metallo 25T: SCX10III

AXI231037

Cage Sides, L R (Gry): RBX10

Käfigseiten, L R (Grau): RBX10

Côtés de cage, D G (gris) : RBX10

Scocca lat, DX/SX (grigio): RBX10

AXI231038

Cage Roof, Hood (Gray): RBX10

Käfigdach, Haube (Grau): RBX10

Toit de cage, capot (gris) : RBX10

Scoc tetto, cofano (grigio): RBX10

AXI231039

Cge Sprts, Btt Try (Gry): RBX10

Käfighalterungen, Akkufach (Grau): RBX10 Supports de cage, support de batterie (gris) Sup scoc, portabatt (grigio): RBX10

AXI231040

Cage Fuel Cell (Gray): RBX10

Brennstoffzelle, Käfig (Grau): RBX10

Pile à combustible cage (gris) : RBX10

Scocca, cella carb (grigio): RBX10

AXI231041

Cge Rdo Bx, Spr Cvr (Gry): RBX10 Käfig, Funkbox, Halterungsabdeckung (Grau): RBX10 Cage, boîte radio, cache support (gris)

Scocca, carter ing (grigio): RBX10

AXI332002

Differential Spool: RBX10

Differentialspule: RBX10

Spool de différentiel : RBX10

Cursore differenziale: RBX10

AXI332005

2-Speed Set: RBX10

2-Gang-Satz: RBX10

Ensemble à 2 vitesses : RBX10

Kit 2 velocità: RBX10

AXI333000

Spring 15x85mm 2.50lbs/in (2)

Feder 15 x 85 mm 2,50 lbs/in (1134 g/Zoll) (2) Ressort 15 x 85 mm 0,28 Nm (2)

Molla 15x85 mm 2,50 lb/in (2)

AXI333001

Spring 15x85mm 1.95lbs/in Purple(2) Feder 15 x 85 mm 1,95 lbs/in (884 g/Zoll), violett (2) Ressort 15 x 85 mm 0,22 Nm violet (2)

Molla 15x85 mm 1,95 lb/in viola (2)

AXI333002

Spring 15x105mm 2.20lbs/in (2)

Feder 15 x 105 mm 2,20 lbs/in (998 g/Zoll) (2) Ressort 15 x 105 mm 0,25 Nm (2)

Molla 15x105 mm 2,20 lb/in (2)

AXI333003

Spring 15x105mm 1.95lbs/in (2)

Feder 15 x 105 mm 1,95 lbs/in (884 g/Zoll) (2) Ressort 15 x 105 mm 0,22 Nm (2)

Molla 15x105 mm 1,95 lb/in (2)

AXI334000

Lower Link Plate Rear (4): RBX1

Untere Lasche, Heck (4): RBX1

Plaque de bras inférieure arrière (4) : RBX1 Bracc inf piastra post (4): RBX10

AXI334001

Sway Bar Set: RBX10

Schwingen-Set: RBX10

Ensemble de barre stabilisatrice : RBX10 Kit barra antirollio: RBX10

DYNB5035H5 11.1V 5000mAh 3S 50C LiPo,Hrdcs:EC5 11,1 V 5000 mAh 3S 50C LiPo, Hartschale: EC5 Li-Po 11,1 V 5 000 mAh 3S 50 C, boîtier : EC5 11,1 V 5000 mAh 3S 50C LiPo, hardcase: EC5

DYNB5045H5 14.8V5000mAh4S50CLiPo,Hrdcs:EC5 14,8 V 5000 mAh 4S 50C LiPo,Hartschale: EC5 Li-Po 14,8 V 5 000 mAh 4S 50C, boîtier : EC5 14,8 V 5000 mAh 4S 50C LiPo, hardcase: EC5

SPM5200

DX5 Rugged DSMR TX w/SR515 DX5 Rugged DSMR TX mit SR515

Émetteur DX5 robuste DSMR avec SR515 Tx DX5 Rugged DSMR con SR515

SPM9068

DX3 Wheel

DX3 Rad

Roue DX3

Ruota DX3

SPM9070

DX3 Cell Phone Mount

DX3 Halterung Mobiltelefon

Support de téléphone portable DX3

Supporto per cellulare DX3

SPMR5010 DX5 Pro DSMR Tx Only

DX5 Pro DSMR nur Tx

Émetteur DX5 Pro DSMR uniquement

DX5 Pro DSMR solo trasmittente

SPMR5115 DX5C SMART 5CH DSMR TX ONLY DX5C SMART DSMR 5-Kanal nur TX

ÉMETTEUR DSMR 5 CANAUX SMART DX5C UNIQUEMENT

DX5C SMART 5CH DSMR solo trasm

SPMR5200G DX5 Rugged DSMR TX Only, Green Nur DX5 Rugged DSMR TX, Grün

Émetteur DX5 robuste DSMR uniquement, vert DX5 Rugged DSMR solo trasm, verde

SPMR5200O DX5 Rugged DSMR TX Only, Orange Nur DX5 Rugged DSMR TX, Orange

Émetteur DX5 robuste DSMR uniquement, orange DX5 Rugged DSMR solo trasm, aranc

SPMSS6250 S6250 U-T / H-S Digital HV WP Servo S6250 U-T / H-S Digitaler HV WP Servo

Servo numérique étanche S6250 U-T/H-S HV Servo digitale imp HV H-S / S6250 U

SPMSS6280 S6280 U-T / H-S Digital HV WP Servo S6280 U-T / H-S Digitaler HV WP Servo

Servo numérique étanche S6280 U-T/H-S HV Servo digitale imp HV H-S / S6280 U

SPMX50003S100H5 5000mAh 3S 11.1V Smart 100C; IC5 5000 mAh 3S 11,1 V Smart 100C, IC5

5 000 mAh 3S 11,1 V Smart 100C ; IC5

5000 mAh 3S 11,1 V Smart 100C IC5

SPMX50003S50H5 5000mAh 3S 11.1V Smart 50C; IC5 5000 mAh 3S 11,1 V Smart 50C; IC5

5 000 mAh 3S 11,1 V Smart 50C ; IC5

5000 mAh 3S 11,1V Smart 50C IC5

SPMX50004S100H5 5000mAh 4S 14.8V Smart 100C; IC5 5000 mAh 4S 14,8 V Smart 100C, IC5

5 000 mAh 4S 14,8 V Smart 100C ; IC5

5000 mAh 4S 14,8 V Smart 100C IC5

SPMX50004S30 5000mAh 4S 14.8V Smart LiPo 30C IC5 5000 mAh 4S 14,8V Smart LiPo 30C; IC5

Li-Po 5 000 mAh 4S 14,8 V Smart 30C IC5 5000 mAh 4S 14,8 V Smart LiPo 30C IC5

SPMX50004S50H5 5000mAh 4S 14.8V Smart 50C; IC5 5000 mAh 4S 14,8 V Smart 50C; IC5

5 000 mAh 4S 14,8 V Smart 50C ; IC5

5000 mAh 4S 14,8V Smart 50C IC5

SPMXCA200 Avian Firma Smart ESC Programmer Avian Firma Smart ESC Programmer

Programmateur ESC Avian Firma Smart

Smart ESC Programmer Avian Firma

SPMXPS4

Smart PowerStage Bundle 4S

Smart PowerStage-Paket 4S

Ensemble Smart Powerstage 4S

Smart Powerstage Bundle 4S

SPMXPS8HC Smart Powerstage Bundle 8S

Smart PowerStage-Paket 8S

Ensemble Smart Powerstage 8S

Smart Powerstage Bundle 8S

SPMXSE1150 Firma 150A Brushless Smart ESC Firma 150A bürstenloser Smart-Geschwindigkeitsregler Variateur ESC sans balais 150 A Smart Firma Smart ESC Firma 150A Brushless

RBX10 RYFT ROCK BOUNCER, 1/10 RTR

EXPLODED VIEW // EXPLOSIONSZEICHNUNG // VUE ÉCLATÉE DES PIÈCES // VISTA ESPLOSA DELLE PARTI

AXI234026 AXI234028

AXI234028

AXI232045 AXI232045

AXI232045
TLR5900 AXA121 AXI236174
AXI232045

AXA013

LOSA6940 AXI232041

AXA1230

AXI234027
AXI234025 AXI234027
AXA118

AXI234022

AXI234026

AXI234022

AXI234028 AXI234026

AXI234021

AXI232051 AXI232052
AXI232051 AX31185

AXI234029 AXI234025
AXA117

AXI236174 TLR5900

AXI232043

AXA120 AXI234027

AXI234025 AXI232039

AXI232051

AXI234026 AXI234028

AXI232040

AX31119

AXI232051

AX31185

TLR255001

LOSA6940

AXA1053 SPMS614
AXA0109

AXA087

AXA1053

AXI232052 AXA087
AXI232051

AXI234021 AXI234025

AXI234020

AXA0147

AXA0109 LOSA6956

AXI232042 AXI234020

AXI232039 AXA1230
AXI232054 AXA087
LOSA6956

AXI234028

AXI234025

LOSA6940 AXI234027 AXA120

AXI232039 AXA118

LOSA6940 AXI232040
AXA1053

TLR255001 AXI232043 AXA121 TLR5900

AXA1230 AXI234029

AXI236174 AXA013
AXI232045 LOSA6940

AXI232041

AXI234029 AXI234025

AXI231026

AXI235167

AXI234027
AXA1041 AXI236103

AXI233023 AXI235097 AXI233020 AXI233029
AXI233020

AXI236174 TLR5900

AXI232045 AXI232045

AXI232054

AXI233024

AXI232053 AXI233030 AXI236105
AXI232053

AXI233023
AXI233029 AXI233020 AXI233020
AXI233027

AXI236105 AXI233030
AXI232053

AXI234027

AXI233021 AXI233020 AXI233020

AXI234027

AXI234025

AXI234028

AXA013 AXI232045

AXA0147

AXI234025 AXI232047
LOSA6940

LOSA6940

AXI234024

AXI234027 AXI234024

AXI232049

AXI234025

AXI234028

AXI234028 AXI232052

AXA1053

AXA087 AX31119

LOSA6956

AXI232042

AXA118 AXI234027

AXI232054

LOSA6956

AXI234030 AXA1053

AXI232047

AXA1230

AXA087

LOSA6940 AXI232051

AXI234023 AX31185

AXI235110

AXI232052

AXA087

AX31185

AXA1053

AXI234030

AXI232051

AXI232049

AXI232047

AXA013

LOSA6940

AXA118 AXI234027

AXI232047 AXI232045

LOSA6940 AXA0147

AXI232051

AXI234023 AXI234028

AXI235110
AXI233020 AXI235097
AXA1041 AXI236103

AXI233025
AXI234030 AXI233029 AXI233020

AXI232045

AXI235167

AXI233026

AXI232054
AXI232053 AXI233030 AXI236105

AXI233020

AXI233025 AXI233029 AXI233020

AXI232053

AXI233028

AXI236105 AXI233030
AXI232053

AXI233021 AXI233020

AXI233020 AXI234030

RBX10 RYFT ROCK BOUNCER, 1/10 RTR

AXI235167
AXI232058 AXI232053 AXI233030 AXI236105

SPMXSE1130 AXI231031

AXA115

AXI231031 Org AXI231036 Blk AXA114
ARAC9830 AX30843 AXA180
AXA083 AXI236015

TLR5907

AXI232053
AXI236105 AXI233030 AXI232053
TLR245011

AXI232055

AXA1391

AXA1391 AXI232057
AXI232058

AXA1221

AXI232056

LOSA6940 AXI232050 AXI232057
LOSA6956

AXA1221

LOSA6956

AXI232057

LOSA6940

SPMXSM2700

AXI232050 AXI235109

AX31120

AXI231025

AXI235097 AXA118

AXI231028 Org AXI231033 Blk

AXI230032

AXA120

AXI235109

AXA114

AXA114 AXI230033

AXI235109

AXA121

AXA118

AXI235110

AXI231027 Org AXI231032 Blk

AXA1059 AXA114

AXA116

AXI231029 Org AXI231034 Blk

AXI235109 AXI231029 Org AXI231034 Blk AXI231028 Org AXI231033 Blk
AXA146
AX31120
AXI231029 Org AXI231034 Blk
AXA116

AXI235097 AXI230032

AXI230033 AXA114
AXI231029 Org AXI231034 Blk

AXI231028 Org AXI231033 Blk

AXI235109

AXI235168

AXI231030 Org AXI231035 Blk

AXA115 AXA1059

AXI231028 Org AXI231033 Blk
AXI231029 Org AXI231034 Blk

AXA114

AXA116
AXI231031 Org AXI231036 Blk

AXA146

AXA118 AXI235110

AX31120

AXI231027 Org AXI231032 Blk
AXI235109
AXA120 AXI235109
AXA118 AXA121
AXI231029 Org AXI231034 Blk AXI235109
AXI230032

AXI235097

RBX10 RYFT ROCK BOUNCER, 1/10 RTR

LOS235015 LOS235015

AXI43011

AXI43002

LOS235015 AXI43002

LOS235015

©2021 Horizon Hobby, LLC. Axial, Ryft, Firma, DSM, DSM2, DSMR, AVC, Active Vehicle Control, Dynamite, Passport, IC5 and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann

Industries, Inc. US 9,320,977. US 10,528,060. US 9,930,567. US 10,419,970. US 10,849,013. Other patents pending.

Created 02/21

62692.2

AXI03005

References

GPL Ghostscript 9.55.0 Adobe InDesign 16.1 (Macintosh)