Instruction Manual for PHILIPS models including: DDPB22-RJ12, Dynalite Network Junction Box, DDPB22-RJ12 Dynalite Network Junction Box
DDPB22-RJ12 RJ12 211 mm (8.31 in) 94 mm (3.70 in) 75 mm (2.95 in) 150 mm (5.91 in) 1 Network Junction Box Installation Instructions Instructions d’installation
File Info : application/pdf, 2 Pages, 804.42KB
DocumentDocumentDDPB22-RJ12 Network Junction Box Installation Instructions Instructions d'installation Installationsanweisungen Instrucciones de instalación Istruzioni per l'installazione Installatie-instructies Devices must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulations. Les appareils doivent être installés par un électricien diplômé conformément à tous les codes et réglementations électriques et de construction nationaux et locaux. Die Geräte sind von einem qualifizierten Elektriker in Übereinstimmung mit allen geltenden Vorschriften zu installieren. Los dispositivos deben ser instalados por un electricista calificado y cumpliendo todas las normas y regulaciones, tanto nacionales como locales, sobre instalaciones eléctricas y obras. I dispositivi devono essere installati da un elettricista qualificato in conformità con le norme locali e nazionali vigenti in materia di costruzioni edilizie e installazione di impianti elettrici. De apparaten moeten worden aangebracht door een gekwalificeerde elektricien en in overeenstemming met alle nationale en plaatselijke elektriciteits- en bouwvoorschriften. / . 150 mm (5.91 in) 94 mm (3.70 in) RJ12 211 mm (8.31 in) 75 mm (2.95 in) 1 IEC Pollution Degree II 1 ¡ ¢ £¤ 1¡ ¥¦ ¡ ¢ £0§¡ ¥¦ 95% +12 V +12 V DD+ GND GND 2 RJ12 - 22 RJ12 - 21 RJ12 - 20 RJ12 - 19 RJ12 - 18 RJ12 - 17 RJ12 - 16 RJ12 - 15 RJ12 - 14 RJ12 - 13 RJ12 - 12 12 V 200 mA RJ12 - 11 IEC Overvoltage Category III 4 SHLD 12 V GND 2 A D + D +12V RJ12 - 1 RJ12 - 2 RJ12 - 3 RJ12 - 4 RJ12 - 5 RJ12 - 6 RJ12 - 7 RJ12 - 8 RJ12 - 9 RJ12 - 10 3 1 GND 2 GND 3 D+ 4 D 5 +12 V 6 +12 V SHLD GND D+ D- +12V 0.3-2.5 mm2 22-12 AWG 0.4 Nm 3.5 Lb-in RS-485 DyNet 2 A 5 6 SHLD GND D+ D+12 V RS-485 DyNet © 2021 Signify Holding. All rights reserved. Specifications are subject to change without notice. No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other trademarks are owned by Signify Holding or their respective owners. www.lighting.philips.com/dynalite AZZ 373 1021 R16Adobe PDF Library 15.0 Adobe InDesign 16.3 (Macintosh)