Welcome to SAL - Lighting a Smarter Future - SAL
Welcome to SAL New Zealand - Lighting a Smarter Future
Welcome to SAL - Lighting a Smarter Future - SAL
Installation Guide for SAL models including: SL9732-20TC-DP3, SL9732-40TC-DP3, SL9732-50TC-DP3, SL9732-20TC-DP3EM, SL9732-40TC-DP3EM, SL9732-50TC-DP3EM, SL9732-20TC-DP3S, SL9732-40TC-DP3S, SL9732-50TC-DP3S, SL9732-20TC3DIM, SL9732-40TC3DIM, SL9732-50TC3DIM, SL9732.TC.DP3 Ecoline Mkiii Led Linear Batten, SL9732.TC.DP3, Ecoline Mkiii Led Linear Batten, Mkiii Led Linear Batten, Led Linear Batten, Linear Batten, Batten
SAL Product Installation Instructions - SAL
File Info : application/pdf, 3 Pages, 1.62MB
DocumentDocumentIMPORTANT: IN THE INTEREST OF PRODUCT PERFORMANCE AND SAFETY PLEASE READ THESE INSTALLATION AND WARRANTY INSTRUCTIONS BEFORE INSTALLING THE PRODUCT. MUST BE INSTALLED DIY BY A LICENSED ELECTRICIAN SAL products are designed in accordance with all mandatory International and AS/NZS Standards, which require installation in accordance with AS/NZS3000 by a qualified installer and regular cleaning and maintenance of the equipment. Products are sold in accordance with the following instructions and SAL standard terms and conditions of sale, available via www.sal.net.au. Due to continued product and information updates, product data sourced from sal.net.au shall not form part of any contract and or technical performance guarantee unless expressly confirmed in writing by SAL at the time of order. ECOLINE MKIII SL9732/TC/DP3 LED LINEAR BATTEN product electrical and installation specification effective 14/8/2024. Model No. SL9732/20TC/DP3 SL9732/40TC/DP3 SL9732/50TC/DP3 SL9732/20TC/DP3EM SL9732/40TC/DP3EM SL9732/50TC/DP3EM SL9732/20TC/DP3S SL9732/40TC/DP3S SL9732/50TC/DP3S SL9732/20TC3DIM SL9732/40TC3DIM SL9732/50TC3DIM Input (V)/(Hz) 220-240/50 220-240/50 220-240/50 220-240/50 220-240/50 220-240/50 220-240/50 220-240/50 220-240/50 220-240/50 220-240/50 220-240/50 Power (W) 10 20 20 40 25 50 10 20 20 40 25 50 10 20 20 40 25 50 20 40 50 Lumens (lm) 1400/1490/1460 2370/2600/2460 2670/2800/2790 4600/5100/4860 3280/3500/3460 6100/6700/6300 1400/1490/1460 2370/2600/2460 2670/2800/2790 4600/5100/4860 3280/3500/3460 6100/6700/6300 1400/1490/1460 2370/2600/2460 2670/2800/2790 4600/5100/4860 3280/3500/3460 6100/6700/6300 2200/2400/2350 4650/4900/4700 6050/6650/6500 Line Current (A) 0.05 0.1 0.1 0.18 0.12 0.22 0.05 0.1 0.1 0.18 0.12 0.22 0.05 0.1 0.1 0.18 0.12 0.22 0.1 0.18 0.22 In-rush Current (A) 7.4A MAX.@12µs 3A MAX.@15µs 4A MAX.@9µs 7.4A MAX.@12µs 3A MAX.@15µs 4A MAX.@9µs 7.4A MAX.@12µs 3A MAX.@15µs 4A MAX.@9µs 5.8A MAX.@4.2µs 6.1A MAX.@3.6µs 8.2A MAX.@8.6µs Dimmable No No No No No No No No No Yes Yes Yes Power Factor > 0.8 > 0.85 > 0.8 > 0.9 > 0.8 > 0.9 > 0.8 > 0.85 > 0.8 > 0.9 > 0.8 > 0.9 > 0.8 > 0.85 > 0.8 > 0.9 > 0.8 > 0.9 > 0.8 > 0.8 > 0.8 Mass (N.W. kg) 0.87 1.21 1.6 1 1.33 1.72 0.92 1.26 1.65 0.9 1.25 1.65 Dimension L x W x H (mm) 600 x 65 x 65 1135 x 65 x 65 1455 x 65 x 65 600 x 65 x 65 1135 x 65 x 65 1455 x 65 x 65 600 x 65 x 65 1135 x 65 x 65 1455 x 65 x 65 600 x 65 x 65 1135 x 65 x 65 1455 x 65 x 65 For SL9732/TC/DP3S: Power (W) 10~50 ( Idle 1W) Input (V)/(Hz) 220-240/50 Installation Heights (m) Max.4 Detection Distance (m) Max. Ø10 Detection Motion Detection Working Speed (m/s) Angle Humidity (RH) 0.5 - 1 360° 10~85% Standby Period Setting (S) 5s/1min/3min/10min Daylight Threshold Sensor Type Disable/30lux Microwave EM Classification C0: D40, C90: D80 Battery Electrical class Class I EM duration Fitting colour CRI White 80 Beam Angle Touch current Operating ambient min/max (°C) 0 to 25 (EM 0 to 25) Storage ambient limit (°C) Operating humidity 10% to 85% RH, NC Storage humidity Calculated TM - 21, L70 @ 85 °C (hrs) Aiming restrictions (if any) 60,000 N/A Reported TM - 21, L 70 @ 85 °C (hrs) Product application IK rating (if relevant) N/A Product installation orientation CCT (K) switch control (TC) Yes CCT (K) Insulation cover rating (if any) N/A PIXIE connectivity Replaceable LED No (see clause 8) IP rating User replaceable LED No (see clause 8) Attachment type IP rating for interior products: The designated IP rating is "from below the ceiling" unless otherwise specified. IP rating ALL products; Termination of the product must be made in accordance with the IP rating. Earth Leakage current: Is calculated in accordance with AS/NZ 60598.1.2017/Amdt 1:2017. FePO4 6.4V, 2Ah >180 mins 120º < 0.7mA 0 to 40 10% to 85% RH, NC 60,000 Interior residential, commercial spaces Horizontal ceiling mount, or suspended 3000/4000/5700 Yes (switch only) IP20 N/A General product application requirements (if applicable) : 1. CCT or POWER selections (where supplied) IMPORTANT, where CCT colour temperature or POWER selection switching is provided, it is important to switch OFF the power before the selection is made, otherwise equipment damage may occur. 2. Recycling SAL encourages recycling, please consider the environment when disposing of packaging, batteries & components. 3. Switching or test intervals For optimum product performance, good design practice does not encourage 24/7 operation of lighting products without the provision of a routine switching or regulatory test cycle. As a guide for continual operation installations, a twelve (12) hour duration for Industrial and Commercial applications and a six (6) hour duration for Residential applications should be considered. 4. Product maintenance In line with the relevant design standards and to protect your investment, it is important to have in place a routine cleaning program that reflects the installation environment and maintains the product in a clean and functional condition. SAL National Pty Ltd. 40 Biloela Street Villawood NSW 2163 ABN 21 633 189 474 Copyright SAL JUN23 | www.sal.net.au | Page 1 of 3 IMPORTANT - The supply must be isolated before any product maintenance or cleaning is conducted. In addition, damage to ANY cable or cord supplied with the product must be addressed as follows; For attachment type X having a specially prepared cable, if the external flexible cable is damaged, it must be replaced by an equivalent cable exclusively available from the manufacturer or authorised installer. For attachment type Y, if the external flexible cable is damaged, it must be exclusively replaced by an equivalent cable by the manufacturer or authorised installer. For attachment type Z, if the external flexible cable is damaged, the cable cannot be replaced and the luminaire must be destroyed. 5. Adverse, corrosive and coastal installation environments Unless the product is specifically designated for such applications in these installation instructions, which is supported by a professional maintenance program; installation of equipment in such environments is not recommended. 6. Dimming products Dimming circuits and product compatibility must be validated by the installer before installation; SAL cannot be responsible for third party changes in dimmer compatibility. 7. Suspended products For installation safety, any suspended products must NOT be installed in high air movement spaces or locations subject to impact. 8. Light source replacements (Non-replaceable light sources) - The light source of the product is deemed not replaceable, when the product reaches its end of life, the complete product must be replaced by a qualified installer. (Non-user replaceable light sources) - The light source of the product must only be replaced by the manufacturer or qualified installer. Caution, risk of electric shock. 9. Interior downlights and sensors with remote drivers and electrical accessories The mounting facilities provided for the device (if any), need only be utilized if in the application of the product is required by AS/NZS3000. Drivers are not designed for installation environments that restrict conventional airflow. 10. Ripple injection, induced flicker (QLD & NSW regions) Installations subject to off-peak ripple induced flicker, (which are beyond the manufactures control), should strongly consider the use of circuit filtering products, or for interior downlight installations, the use of products designed to block the signal interferences, such as the SAL rippleSHIELD series. 11. Floodlight products Unless nominated aiming restrictions or installation parameters apply, products are designed for installation environments between ground and 15 metres in height, subject to the desired optical performance being achieved. For floodlight installation environments that have restricted access (eg: columns and roof-lines) which are subject to unstable electrical supply or electrical surges (which void warranty), consideration of the installation of an independent surge protector is strongly recommended. 12. Emergency enabled products In the interest of transport and safety, emergency products are supplied with the battery disconnected. In addition to specific emergency commissioning instructions, this battery MUST be connected at the time of installation. Continual use in emergency mode greater than 240 hours without recharge, will result in battery failure and void battery warranty. 13. Specific installation procedures (if any) - this device must be installed by a licensed electrician: CAUTION CHECK Terminate the conductors & select the CCT and power (where relevent). Emergency model wiring diagrams Switch Control Maintained Mode Non-Maintained Mode N UA SA N UA SA Emergency models commissioning and operation 1. Switch on mains supply. The charge monitor LED will illuminate. 2. Allow the unit to operate for 30 minutes and then depress the test switch to check emergency operation. 3. Release the test switch and allow the unit to operate for 16 hours to fully charge the battery after which time the unit is ready. 4. Self-contained emergency luminaires shall be subjected to a battery discharge test for the required duration at regular intervals in accordance with AS/NZS 2293 applicable to emergency lighting. Batteries should be replaced with the same brand/type when the rated duration is no longer achieved. Important safety issues * This product must be installed by a qualified electrician according to AS/NZS 3000. * The supply must be isolated before opening or accessing the luminaire. Note: In the interest of safety, the 6 monthly test should be undertaken during daylight hours to allow for the possibility of failures of the standard lighting supply whilst the battery is discharged. SAL National Pty Ltd. 40 Biloela Street Villawood NSW 2163 ABN 21 633 189 474 Copyright SAL JUN23 | www.sal.net.au | Page 2 of 3 Sensor model parameter setting: Shown in chart belowBy setting the S1 to set the detection RANGE of products, by setting S2, S3 to set the DELAY time of products, by setting the S4 to set the LIGHT-control of products. Ceiling Mounted 0.5-1.0M/S 1 2 Mounting 3 Height 4 5 6 7 10 8 6 4 2 0 2 4 6 8 10 Mounting Height Wall Mounted 1 234 5 6 7 12 9 6 3 0 3 6 9 12 MAXIMUM DETECTION ZONE LIMITED DETECTION ZONE Switch UP Switch DOWN Daylight threshold 4 Disable 30lux Definition of the ambient brightness; only when the ambient brightness is lower than the preset specific lux amount, the sensor will respond; when it's preset mode is "disable", the sensor detects everytime it detects motion regardless the ambient brightness. Hold-time 23 5s 1min 3min 10min The period of light maintaining 100% brightness after moving objects leave the detection area from the last motion detected. Detection area 1 100% 50% In this area, movement will be detected and trigger the sensor. 100% detection area is also known as the strong sensitvity. MANUAL OVERRIDE: · To enable `Manual Override' or `Permanent On', simply switch off and on three times with an interval of 1 second. The lights will now stay on permanently. To return to `Automatic Mode', switch the unit off and after 1 minute switch on again. The unit will resume normal operation. 14. Warranty In accordance with SAL's standard terms and conditions of sale, SAL warrant this product to be free from defects in materials and or workmanship for a period as stated below for goods not subject to incorrect installation, maintenance, operation, mishandling, environmental, unauthorised modifications or electrical operating conditions outside the nominated product specification as detailed in these installation instructions. The benefits to you given by this warranty are in addition to other rights and remedies you have under law. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Warranty term Residential usage (60) months, Commercial usage (36) months, Replaceable Lamps (where supplied) (12) months and Lithium batteries where supplied (24) months from date of purchase. For New Zealand, please refer to www.sal.co.nz for warranty conditions and service. How to make a claim? Step # 1 Within 30 days of the fault discovery, please contact the original place of the SAL product purchase during standard (local) business hours, with the following information (a) proof of purchase (b) description and quantity of the claimed fault (c) address of installation. (d) operating hours of the product. Step # 2 It is then the responsibility of the original place of product purchase to report the matter to SAL aftersales; NSW | ACT QLD VICT | TAS SA | NT WA NZ - SAL National Pty Ltd, 40 Biloela Street Villawood NSW 2163 - SAL National Pty Ltd, 36 Whitelaw Place Richlands QLD 4077 - SAL National Pty Ltd, 46-48 Keys Road Moorabbin Victoria 3189 - SAL National Pty Ltd, 79 Fredrick St Welland SA 5007 - SAL National Pty Ltd, 29 Beringarra Av Malaga WA 6090 - Hamer, 130 Bush Road, Albany, Auckland, 0632 | P # 02 9723 3099 | P # 07 3879 5999 | P # 03 9532 3168 | P # 08 7084 1958 | P # 08 9248 7458 | P # 0800 239 239 Step # 3 - Upon review of your claim and if the product is required to be returned to SAL for technical evaluation, then at the owners expense the product must be returned to SAL as per the above nominated locations. Step # 4 - Pending the evaluation, the claim will be validated resulting in the product being repaired or replaced with the same or best equivalent product at the discretion of SAL, or rejected if the product fault was found to be caused by conditions beyond the responsibility of SAL warranty obligations. Consideration of installation, product removal, return freight and or testing fees are not the responsibility of SAL. SAL National Pty Ltd. 40 Biloela Street Villawood NSW 2163 ABN 21 633 189 474 Copyright SAL JUN23 | www.sal.net.au | Page 3 of 3