Installation Guide for iBoard models including: IB-228C, IB-228H, IB-228C Running Board Side Step Bars, Running Board Side Step Bars, Board Side Step Bars, Side Step Bars, Bars
HD Ridez Running Board Side Step Bars 6" Black Compatible with Nissan Xterra 2005-2015 (Nerf Bar Side Steps Side Bars) : Automotive
Auto Parts & Auto Accessories - Over 4000 Auto Parts, Aftermarket Parts, Truck Accessories & Car Accessories
iBoard® iBoard® by APS READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED. *ROCKER PANEL MOUNT *NO DRILLING REQUIRED PART#: IB-228C&H Fastener Size Tightening Torque (ft-lbs) 6mm 6-7 8mm 16-18 10mm 31-32 12mm 56-58 14mm 92-94 Required X X X X PART LIST Driver Side Step Bar 1# Front Passenger Side Step Bar 2# 1# 2# 1# 2# Customer Support: info@iboardauto.com 1 Rev. 20230401 iBoard® Mounting Bracket List Item QTY Description Item QTY Description 1# 3 Driver Front/Center/Rear Mounting Brackets 2# 3 Passenger Front/Center/Rear Mounting Brackets Hardware Package A (For Bracket Installation) Item QTY Description Item QTY Description 1# 12 M8 Large Flat Washers 2# 12 M8X1.25 Nylon Lock Nuts 1# 2# Hardware Package B (For Stainless Steel Step Bar Installation) Item QTY Description Item QTY Description 1# 12 M8X1.25-35mm Carriage Bolts 3# 12 M8 Nylon Lock Nuts 2# 12 M8 Large Flat Washers 4# 6 Sliders (Packed with Step Bars) 1 # 2 # 3 # 4 # Customer Support: info@iboardauto.com 2 Rev. 20230401 iBoard® STEP 1 Start installation from the driver side front of the vehicle. Locate the (2) factory threaded studs located on the side of the inner body panel, (Fig 1). STEP 3 Move to the center & rear mounting location. Repeat Steps 1 2 for Driver Center & Rear Mounting Brackets. Note: All (3) Driver Side Mounting Brackets are universal. Threaded Studs Front (Fig 1) Driver Side Front Mounting Location STEP 2 Select the Driver Front Mounting Bracket. Attach to the (2) factory threaded studs with (2) M8 Large Flat Washers and (2) M8X1.25 Nylon Lock Nuts, (Fig 2). Do not fully tighten hardware at this time. (2) M8 Large Flat Washers (2) M8X1.25 Nylon Lock Nuts Front STEP 4 Once all (3) Driver side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 3 & 4) (1) Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts; (2) Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider. (3) Slide the Slider (with carriage bolts) to the Step Bar. (4) Repeat to install the other (2) sliders to the step bar. (5) Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brackets. Secure the Step Bar to the installed Brackets by using (6) M8 Large Flat Washers and (6) M8 Nylon Lock Nuts and (3) Sliders, (Fig 4). Do not fully tighten hardware at this time. Note: The Sliders are packed with the Step Bars. Level and adjust the Step Bar and fully tighten all hardware. Repeat Steps 1-4 for the other side Step Bar installation. The installation is completed!!! NOTE: All (3) Passenger Side Mounting Brackets are universal. (Fig 2) Driver Side Front Mounting Bracket Installation Attention Do periodic inspections to the installation to make sure that all hardware is secure and tight. In order to protect your bars/boards, please use mild soap/non-abrasive products for cleaning only. Customer Support: info@iboardauto.com 3 Rev. 20230401 iBoard® Slider (2) Carriage Bolts (Fig 3) Slider Installation Slider with (2) Carriage Bolts Step Bar Slider (w/ installed Carriage Bolts) Step Bar (Bottom View) Mounting Bracket (2) M8 Large Flat Washers (2) M8 Nylon Lock Nuts (Fig 4) Step Bar Installation Customer Support: info@iboardauto.com 4 Rev. 20230401Microsoft Publisher LTSC