KK-228WB Multi-function Emergency Radio Manual
Document Reference: A2
I. COMPONENT NAMES
The diagram shows a multi-function emergency radio. Key components are labeled with numbers:
- 1. Flashlight switch
- 2. Flashlight
- 3. Table lamp buckle position
- 4. LED desk lamp
- 5. Frequency dial
- 6. Speaker
- 7. Channel button
- 8. AM/FM/WB/BT switch
- 9. Volume knob/radio/power switch
- 10. Solar panel
- 11. Antenna
- 12. Charge indicator light
- 13. 5V input/output interface
- 14. SOS switch
- 15. Bluetooth indicator light
- 16. Radio indicator light
2. Keys Description
| Symbol | Name | Operation | Function | Functional description |
|---|---|---|---|---|
| ? | Switch | The flashlight | Open the flashlight | Short press the button: flashlight on |
| SOS | Switch | Siren&Blink | long press: turn on Siren&Blink; short press: turn off Siren&Blink |
II. OPERATION INSTRUCTIONS
Charge the product before use.
1. Charging Method
(Turn off the radio during normal charging; if charging the product when the radio is working, it can only ensure the power supply of the radio)
1) USB charging (adaptor)
Connect the charging cable (DC 5V 2A) to the product's Type-C port [13] and charge it directly. The battery indicator light blinks during charging.
2) Dynamo charging
Open crank handle to charge the product with rotation (clockwise or counterclockwise). Remain 120-180 cycles/min; the battery indicator light blinks during charging.
3) Solar charging
Put it in a sunny place for charging, and make the sun shine directly on the solar panel [10] as much as possible. The higher the brightness of the charge indicator light [12], the higher the charging efficiency.
5. Radio Usage Steps
1) Turn on [9] radio button.
2) Select the channel:
- FM: 87-108MHz;
- AM: 520-1710KHz;
- WB: 162.400-162.550MHz;
3) Use channel button [7] to select the channel; the radio indicator light [16] is on when a station is captured.
4) Use knob [9] to adjust the volume.
5) Pull out the [11] radio antenna to enhance the radio signal when using FM / WB.
6. Desk Lamp Usage Steps
Adjust the desk lamp [4] to the desired angle and turn it on.
III. UNIT SPECIFICATION
- Built-in battery: 3.7V 2000mAh 18650
- Flashlight: 1PC LED (Weak light 0.5W, Strong light 1W)
- Desk lamp: 10PCS LED (Weak light 0.5W, Strong light 1W)
- Range of radio: FM:87-108MHz; AM:520-1710KHz; WB:162.400-162.550MHz;
- Solar panel specification: 5.5V 30mA
- Lifespan of light sources: >10000H
- Charging input: DC 5.0V 1.2A
- Output power: DC 5.0V 1.0A
- Unit weight: 309 g
- Unit size: 147.5*81*50.8mm
IV. PRECAUTIONS
- The product is not suitable for children below 8 years old.
- Avoid prolonged use of the device in extremely cold, hot, dusty and moist environment.
- The indicator light blinks signifies low battery mode.
- Clean the product with a cloth dipped with some neutral detergent.
FCC Compliance Information
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- - Reorient or relocate the receiving antenna.
- - Increase the separation between the equipment and receiver.
- - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- - Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- (1) This device may not cause harmful interference and
- (2) This device must accept any interference received including interference that may cause undesired operation changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
FCC RF waning statement: the device has been evaluated to meet general RF exposure requirement, The device can be used in portable exposure condition without restriction.