Roll A Shade - Commercial Window Shade Solutions
Roll A Shade - Commercial Window Shade Solutions
Installation Guide for ROLL A SHADE models including: Infinity Shade, Infinity, Shade
Infinity Shade - Roll A Shade
File Info : application/pdf, 6 Pages, 1.16MB
DocumentDocument12101 Madera Way Riverside, CA 92503 Phone: 888-245-5077 Fax: 951-245-5075 www.rollashade.com RAS - Installation Instructions Infinity Shade Manual Hardware Included Tools Required Self Tapping Self Tapping Wood Screws Metal Stop Screws for Phillips for (If requested) Balls Aluminium Tension Device Drill Brackets 1. Install Bracket Attach the brackets to the window frame, window molding, wall or ceiling per diagram. Brackets are universal so clutch may be mounted on either side. Two screws must be installed in each bracket as shown. 1/4" Hex Head Phillips Head SIDE (screw in through side) CEILING BACK 2. Install Shade Put the spring loaded pin into the round hole of the bracket (A). Keeping the pin end secured in it's bracket, insert the hook arms on the clutch straight into the two hook arm receiver holes on the bracket (B). Once the two hook arms are through the holes, gently pull down on the clutch until the two hook arms have locked securely to the bracket. The bottom of the clutch should always point straight down. TOP MULLION 3. Shade Adjustment (If Necessary) Roll shade up and down to conrm bottom rail is level and material rolls up straight on center tube. If the bottom rail is not level, lower shade until you see the metal tube. Add layers of masking tape to the metal tube to the end that is too low until bottom rail is straight. If the material tracks to one side, lower shade until you see the metal tube. Add layers of masking tape to the metal tube to the end that is opposite the direction of tracking, until shade rolls up straight. www.rollashade.com © Copyright 2025 Roll A Shade® Inc., All rights reserved. - Contractor #916075 RASINFSMLVER.1 Page 1 of 2 5. Install Metal Stop Ball to Bead Chain Pull the rear chain to lower the shade to appropriately 1/4" above sill and attach connector or stop ball to upper most bead on front chain closest to the clutch. By attaching this connector or stop ball you will set how far the shade will lower. Pull the front chain and raise the shade so the bottom rail is 5" below the shade and attach a connector or stop ball on the back chain at upper most bead. Metal Bottom Stop 6. Install Chain Anchor The chain anchor is a plastic piece that is attached to the chain to secure it from possible accidents. Position the chain anchor on the window frame so that the chain anchor and chain do not interfere with raising or lowering the shade. The chain anchor should be installed without stretching or pulling down on the chain. Leave a little play through the chain anchor to allow the chain to pass freely. Do not twist or cross the bead chain. Secure the anchor with Phillips screws in both upper and lower holes. Warning: Failure to use this device may cause injury or death Metal Top Stop Window Blind Cord Can STRANGLE Your Child · Children can climb furniture to reach cords · Move cribs and other furniture away. · Keep all cords out of children's reach. · Attach tension device to wall or floor. · Fasteners provided with the tension device may not be appropriate for all mounting surfaces. · Use appropriate anchors for the mounting surface conditions. www.rollashade.com © Copyright 2025 Roll A Shade® Inc., All rights reserved. - Contractor #916075 RASINFSMLVER.1 Page 2 of 2 TENSION DEVICE INSTALL ATION INSTRUCTIONS Rollashade.com info@rollashade.com 951.245.5077 © Copyright Roll A Shade® Inc. All Rights Reserved. HARDWARE INCLUDED Tension Device + Chain Tension Device Bracket Short Screws Screws INSIDE OR OUTSIDE APPLICATION OUTSIDE INSIDE TOOLS REQUIRED 3/8" Hex Head Phillips Head 1/8" Drill Bit Drill INSIDE OUTSIDE RASTDV2VER.2 2 OF 4 | © Copyright Roll A Shade® Inc. All Rights Reserved. INSIDE MOUNT & TENSION DEVICE INSTALLATION Pull the Chainhold down until the chain is fully tensioned (plunger will be fully raised). Screw device into wall. A B KEEP TENSION C SECURE TENSION DEVICE NOTE: Please make sure shade operates smoothly. RASTDV2VER.2 3 OF 4 | © Copyright Roll A Shade® Inc. All Rights Reserved. OUTSIDE MOUNT & TENSION DEVICE INSTALLATION With provided screws, install bracket first with large screws (use Chainhold marked screw hole locations as reference). Pull the Chainhold down until the chain is fully tensioned (plunger will be fully raised). Install Chainhold into bracket with small screws. A B PULL CHAIN DOWN & MARK LOCATION C REMOVE TENSION DEVICE & DRILL D E PLACE TENSION DEVICE ON BRACKET F SECURE TENSION DEVICE NOTE: Please make sure shade operates smoothly. RASTDV2VER.2 4 OF 4 | © Copyright Roll A Shade® Inc. All Rights Reserved.